Engineering Papers⌕ Search

Engineering topics

Compton, Brett G.

Publications and source records attributed to Compton, Brett G..

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tuning crosslinking of hybrid preceramic polymers in vat photopolymerization toward controlled ceramic yields

Control of preceramic polymer crosslinking for UV-curable processing is essential for fine 3D printing with high ceramic conversion for sustainable polymer-derived ceramics (PDC) engineering. While various factors influencing ceramic yield have been studied, the systematic exploration of the relationship between crosslinking and ceramic yield, especially when crosslinking increases volatile elements, remains open for further investigation. This study addresses this gap by utilizing vat photopolymerization (VP) additive manufacturing (AM) as a versatile platform for controlling preceramic crosslinking and ceramic yield. By rationally designing and tuning the photochemical crosslinking through digital light processing (DLP), we demonstrate that the ceramic yield can be enhanced from 64% to over 86%, even with added volatile elements. We reveal that the post-pyrolysis ceramic yield can be closely correlated with the pre-pyrolysis crosslinking of the preceramic network represented by its stiffness. This correlation thereby suggests a fast, energy-efficient, non-destructive methodology to predict and improve ceramic yield. Combined with these findings, our one-pot thiol-ene hybridization of polycarbosilane and polycarbosiloxane via DLP offers an exemplary method to generate hybrid preceramic polymers with tailored material properties toward target applications, and potentially even higher ceramic yields. This study thus contributes to achieving better resource- and energy-efficient preceramic polymer and PDC processing routes toward sustainable, advanced organic–inorganic materials manufacturing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Large-scale reactive thermoset printing: Complex interactions between temperature evolution, viscosity, and cure shrinkage

Thermoset composites are strong candidates for large-scale material extrusion additive manufacturing (AM). However, uncured thermoset composites become unstable as print height increases. Here, chemical initiation of vinyl ester immediately before deposition was used to suppress collapse and enable large-scale thermoset printing. Structural stability was assessed by printing thin walls at various layer times and monitoring thermal gradients with an infrared camera. Stable printing was observed at a layer time of 4.50 min, approximately half the gel time of the material (8 min). Self-weight collapse occurred at short layer time (0.68 min), whereas warpage occurred at long layer time (6.50 min). Here, a new behavior was discovered at intermediate layer time (2.25 min) where the heat generated by the reaction causes new, un-gelled layers to flow. Forced convection eliminates this behavior, stabilizing the 2.25-min layer time print. These findings motivated development of a less exothermic material system, which was used to print a large-scale mold and demonstrate the value of this understanding. By presenting these challenges of large-scale reactive thermoset AM for the first time, this work motivates focused studies of the complex interplay between rheological, thermal, and chemical behaviors to improve the feasibility of large-scale thermoset AM. Tensile properties of the printed material were also measured. Longitudinal and transverse elastic moduli are 3.79 and 2.95 GPa, respectively, and corresponding tensile strengths are 36.11 and 18.83 MPa. The glass transition temperature is 93.13 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Structural stability of thin overhanging walls during material extrusion additive manufacturing of thermoset-based ink

Recent developments have enabled material extrusion additive manufacturing of thermoset-based composite inks on the large scale. In addition, printing out-of-plane components is of broad interest to the polymer material extrusion community. Here, we address some of the challenges associated with both large-scale and out-of-plane thermoset material extrusion additive manufacturing by studying the height at which thin overhanging walls collapse. Walls at a range of overhang angles were printed until they collapsed. An optical camera captured the profile of each wall throughout the print, allowing the collapse height to be identified and the geometric fidelity to the programmed angle to be evaluated. Using previously measured rheological properties, predictive models were generated to approximate the collapse height and profile of the deflected walls. First, an analytical model was created to predict the height at which the walls would yield. The analytical model assumes the walls exhibit a perfectly linear profile; however, experiments proved this assumption to be false. Therefore, a finite element simulation was developed to account for the elastic deflection that occurs during printing. The finite element simulation predicts both the yield height and the deflected profile after the deposition of each layer. For the properties of the thermoset ink used here, the yield height predicted by the analytical model and finite element simulation are virtually identical. These predictions match experimental data reasonably well, but minor errors are observed. Accounting for the fully plastic moment appears to explain the small mismatch between experimental data and predictions. Additionally, the finite element simulation provides an excellent prediction of the deflected profile before the wall begins to collapse. Finally, by demonstrating that the collapse height and deflected profile of thin overhanging walls can be predicted, this work illustrates how the soft viscoelastic properties of thermoset-based composite inks limit the scale of a key feature required to print some nonplanar components. It also provides a basis to tailor in-process curing systems to suppress deflection and collapse of thin overhanging walls.

36 MATERIALS SCIENCE↗