Engineering topics

Collier, F.

Publications and source records attributed to Collier, F..

5 records

NASA NTRS1990

Blunt-nosed swept supercritical LFC wings without nose flaps

To simplify the design of swept supercritical (SC) Laminar Flow Control (LFC) wings and maintain satisfactory low speed characteristics, blunt-nosed swept SC LFC wings without nose flaps and lower wing loadings were studied. Their boundary layer crossflow in the leading edge area is optimally controlled (1) by compensating the boundary layer crossflow of the front acceleration zone by an opposite crossflow in a downstream pressure rise area, (2) by maintaining a neutrally stable boundary layer crossflow by suction within a narrow spanwise suction strip located close to the wing attachment line in the front acceleration zone. The required suction massflow and power are then very small, especially considering the strongly stabilizing effect of surface and streamline curvature on crossflow stability.

Pfenninger, W.↗

NASA NTRS1986

Turbulence alteration due to shock motion

Physical and computational models are provided for three cases of shock motion-turbulence interaction: (1) the production of velocity fluctuations due to shock oscillations; (2) eddy alteration due to transient eddy shocklets; and (3) eddy production due to transient shock-entropy spottiness interactions. Shock motions are shown to be efficient in converting mean flow energy into fluctuation energy, and high-frequency induced shock motions produce intense vorticity fields from the incident mean flow. The effects of transient eddy shocklets created by subsonic eddy motion in a supersonic stream are discussed in detail.

Hussaini, M. Y.↗

NASA NTRS1982

Turbulent boundary layer over solid and porous surfaces with small roughness

The wind tunnel models and instrumentation used as well as data reduction and error analysis techniques employed are described for an experimental study conducted to measure directly skin friction and obtain profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary on a large diameter axisymmetric body. Results are given for such a body with a (1) smooth, solid surface; (2) a sandpaper roughened, solid surface; (3) a sintered metal, porous surface; (4) a ""smooth'' performated titanium surface; (5) a rough, solid surface made of fine diffusion bonded screening; and (6) a rough, porous surface made of the same screening. The roughness values were in low range (k+ 5 to 7) just above what is normally considered ""hydraulically smooth''. Measurements were taken at several axial locations and tow or normal stream freestream velocities, 45.1 m/sec and 53.5 m/sec.

Kong, F. Y.↗

NASA NTRS1982

Turbulent boundary layer over solid and porous surfaces with small roughness

Skin friction and profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary layer were measured directly on a large diameter, axisymmetric body with: (1) a smooth, solid surface; (2) a sandpaper-roughened, solid surface; (3) a sintered metal, porous surface; (4) a smooth, perforated titanium surface; (5) a rough solid surface made of fine, diffusion bonded screening, and (6) a rough, porous surface of the same screening. Results obtained for each of these surfaces are discussed. It is shown that a rough, porous wall simply does not influence the boundary layer in the same way as a rough solid wall. Therefore, turbulent transport models for boundary layers over porous surfaces either with or without injection or suction, must include both surface roughness and porosity effects.

Kong, F. Y.↗

NASA NTRS1972

Apollo experience report: Lunar module environmental control subsystem

A functional description of the environmental control subsystem is presented. Development, tests, checkout, and flight experiences of the subsystem are discussed; and the design fabrication, and operational difficulties associated with the various components and subassemblies are recorded. Detailed information is related concerning design changes made to, and problems encountered with, the various elements of the subsystem, such as the thermal control water sublimator, the carbon dioxide sensing and control units, and the water section. The problems associated with water sterilization, water/glycol formulation, and materials compatibility are discussed. The corrective actions taken are described with the expection that this information may be of value for future subsystems. Although the main experiences described are problem oriented, the subsystem has generally performed satisfactorily in flight.

Gillen, R. J.↗