Engineering Papers⌕ Search

Engineering topics

Coe, H. H.

Publications and source records attributed to Coe, H. H..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Comparison of predicted and experimental performance of large-bore roller bearing operating to 3.0 million DN

Bearing inner and outer race temperatures and the amount of heat transferred to the lubricant were calculated by using the computer program CYBEAN. The results obtained were compared with previously reported experimental data for a 118 mm bore roller bearing that operated at shaft speeds to 25,500 rpm, radial loads to 8,900 N (2000 lb), and total lubricant flow rates to 0.0102 cu m/min (2.7 gal/min). The calculated results compared well with the experimental data.

Coe, H. H.↗
NASA NTRS1980

Calculated and experimental data for a 118-mm bore roller bearing to 3 million DN

The operating characteristics for 118 mm bore cylindrical roller bearing are examined using the computer program CYBEAN. The predicted results of inner and outer-race temperatures and heat transferred to the lubricant generally compared well with experimental data for shaft speeds to 3 million DN (25,000 rpm), radial loads to 8900 N (2000 lb), and total lubricant flow rates to 0.0102 cu m/min (2.7 gal/min).

Coe, H. H.↗
NASA NTRS1978

Predicted and experimental performance of jet-lubricated 120-millimeter-bore ball bearings operating to 2.5 million DN

Bearing inner- and outer-race temperatures and friction power losses were calculated using two computer programs. The values obtained were compared with previously reported experimental data for 120 mm bore bearings which operated at thrust loads to 22 240 N (5000 lb), shaft speeds to 20 800 rpm, and with two lubricant flow rates. One program severely underestimated the power loss, while the other, called SHABERTH, provided a good prediction of both race temperatures and power losses.

Coe, H. H.↗
NASA NTRS1976

Performance of 75-millimeter bore arched outer-race ball bearings

An investigation was performed to determine the operating characteristics of 75-mm bore, arched outer-race bearings, and to compare the data with those for a similar, but conventional, deep groove ball bearing. Further, results of an analytical study, made using a computer program developed previously, were compared with the experimental data. Bearings were tested up to 28,000 rpm shaft speed with a load of 2,200 N (500 lb). The amount of arching was 0.13, 0.25, and 0.51 mm (0.005, 0.010, and 0.020 in). All bearings operated satisfactorily. The outer-race temperatures and the torques, however, were consistently higher for the arched bearings than for the conventional bearings

Coe, H. H.↗
NASA NTRS1976

Experimental performance of 75-millimeter-bore arched outer-race ball bearings to 2.1 million DN

An experimental investigation was performed to determine the operating characteristics of arched outer-race bearings and to compare the data with those for a similar, but conventional, deep-groove ball bearing. The bearings were tested over a range of shaft speeds up to 28,000 rpm at a thrust load of 2200 newtons (500 lb). One bearing was operated at 26,000 rpm with a range of thrust loads. The amounts of arching were 0.13, 0.25, and 0.51 millimeter (0.005, 0.010, and 0.020 in.). All bearings operated satisfactorily; the arched bearing outer-race temperatures and torques were consistently higher than those for the conventional bearing.

Coe, H. H.↗
NASA NTRS1976

Performance of 75 millimeter-bore arched outer-race ball bearings

An investigation was performed to determine the operating characteristics of 75-mm bore, arched outer-race bearings, and to compare the data with those for a similar, but conventional, deep groove ball bearing. Further, results of an analytical study, made using a computer program developed previously, were compared with the experimental data. Bearings were tested up to 28,000 rpm shaft speed with a load of 2200 N (500 lb). The amount of arching was 0.13, 0.25, and 0.51 mm (.005, .010, and .020 in.). All bearings operated satisfactorily. The outer-race temperatures and the torques, however, were consistently higher for the arched bearings than for the conventional bearing.

Coe, H. H.↗
NASA NTRS1975

Bending stresses in spherically hollow ball bearing and fatigue experiments

Spherically hollow balls of 21.7, 50.0 and 56.5 per cent mass reduction have been operated in ball bearings and in a 5-ball fatigue tester with differing outcomes. Available theoretical and experimental treatments of stresses in spherically hollow balls are reviewed and compared. Bending stresses are estimated for these spherically hollow balls to better understand the differences in ball bearing and fatigue test experience.

Nypan, L. J.↗
NASA NTRS1975

Performance of 75-millimeter-bore bearings using electron-beam-welded hollow balls with a diameter ratio of 1.26

An experimental investigation was performed to determine the rolling element fatigue life of electron beam-welded hollow balls with a diameter ratio (o.d./i.d.) of 1.26 and to determine the operating characteristics of bearings using these hollow balls. Similar bearings with solid balls were also tested and the data compared. The bearings were operated at shaft speeds up to 28,000 rpm with a thrust load of 2200 N (500 lb). Ball failures during the bearing tests were due to flexure fatigue. The solid and hollow ball bearings tested showed little difference in outer race temperatures and indicated the same bearing torque. The 17.5-mm (0.6875-in.) diameter balls were also tested in the five-ball fatigue tester and showed no significant difference in life when compared with the life of a solid ball.

Coe, H. H.↗
NASA NTRS1975

Bending stresses in spherically hollow ball bearing and fatigue experiments

Spherically hollow balls of 21.7, 50.0, and 56.5 percent mass reduction were operated in ball bearings and in a five-ball fatigue tester with differing outcomes. Available theoretical and experimental treatments of stresses in spherically hollow balls are reviewed and compared. Bending stresses are estimated for these spherically hollow balls to better understand the differences in ball bearing and fatigue test experience.

Nypan, L. J.↗
NASA NTRS1974

An experimental evaluation of the stresses in drilled balls

Stresses in dimensionally similar large models of 40-, 50- and 60-percent mass reduction cylindrically hollow 'drilled' bearing balls were experimentally evaluated with flat strain gage rosettes. Dimensionless principal stress coefficients were calculated and were applied to estimate the bending stresses in the drilled balls of three series of full-scale bearing experiments. Stresses were highest when the applied load approached the edge of the hole, and ranged up to almost 620 million Newtons per sq m at the bore.

Nypan, L. J.↗
NASA NTRS1973

Analysis of stresses at the bore of a drilled ball operating in a high-speed bearing

Three-dimensional stress distributions were calculated for both a regular drilled ball with a stiffening web. The balls were 20.6 mm (0.8125 in.) in diameter and had a 12.6 mm (0.496 in.) diameter concentric hole. The stiffening web was 1.5 mm (0.06 in.) thick. The calculations showed that a large reversing tangential stress at the hole bore was reduced by one-half by the addition of the web.

Coe, H. H.↗