Engineering topics

Claus, R. W.

Publications and source records attributed to Claus, R. W..

28 records · Page 2

NASA NTRS1984

Accelerated convergence for incompressible flow calculations

Two improved algorithms which solve the steady-state Navier-Stokes equations, PISO and SIMPLER, are studied. Computations were carried out on progressively finer grids for the driven cavity and flow over a backward-facing step. The effects of relaxation factor, number of grid nodes and number of sweeps through the pressure equations are studied to evaluate the performance of the PISO and SIMPLER schemes. Results show that these improved schemes accelerate the convergence rate of the solution generally by a factor of two as compared to the SIMPLE method.

Neely, G. M.↗

NASA NTRS1984

Reducing numerical diffusion for incompressible flow calculations

A number of approaches for improving the accuracy of incompressible, steady-state flow calculations are examined. Two improved differencing schemes, Quadratic Upstream Interpolation for Convective Kinematics (QUICK) and Skew-Upwind Differencing (SUD), are applied to the convective terms in the Navier-Stokes equations and compared with results obtained using hybrid differencing. In a number of test calculations, it is illustrated that no single scheme exhibits superior performance for all flow situations. However, both SUD and QUICK are shown to be generally more accurate than hybrid differencing.

Claus, R. W.↗

NASA NTRS1983

Analytical calculation of a single jet in cross-flow and comparison with experiment

A series of progressively finer grid systems to calculate the single jet in cross-flow experimentally measured were employed. The experimental measurements provide a collection of velocities, turbulence intensities, and jet concentration profiles with measurements of the inlet field. The use of a series of progressively finer grid systems allows a differentiation between numerical errors and the hydrodynamic modeling assumptions embodied in the 3D combustor code.

Claus, R. W.↗

NASA NTRS1983

Flame Radiation Measurements

Spectral and total flame radiation measurements exhibited: (1) that radiant heat flux increases with vision combustor inlet air pressure; (2) the effect of fuel atomization characteristics on radiant heat flux; and (3) that a reduction in fuel hydrogen content produces a significant increase in radiant heat flux primarily at low combustor pressures.

Claus, R. W.↗

NASA NTRS1983

Parametric study of flame radiation characteristics of a tubular-can combustor

A series of combustor tests were conducted with a tubular-can combustor to study flame radiation characteristics and effects with parametric variations in combustor operating conditions. Two alternate combustor assemblies using a different fuel nozzle were compared. Spectral and total radiation detectors were positioned at three stations along the length of the combustor can. Data were obtained for a range of pressures from 0.34 to 2.07 MPa (50 to 300 psia), inlet temperatures from 533 to 700K (500 to 800 F), for Jet A (13.9 deg hydrogen) and ERBS (12.9% hydrogen) fuels, and with fuel-air ratios nominally from 0.008 to 0.021. Spectral radiation data, total radiant heat flux data, and liner temperature data are presented to illustrate the flame radiation characteristics and effects in the primary, secondary, and tertiary combustion zones.

Humenik, F. M.↗

NASA NTRS1983

Flame radiation and liner heat transfer in a tubular-can combustor

Heat transfer within a combuster were examined. Total and spectral flame radiation in a tubular can combustor at a series of parametric operating conditions was measured. Radiation measurements were taken for a range of inlet air pressures from 0.34 to 2.0 MPa, inlet air temperatures from 533 to 700 K, with two different fuels, Jet-A and ERBS. Measurements of liner temperatures combined with the parametric radiation results allowed a calculation of the combustor liner heat loads. Flame emissivity was determined from the spectral measurements.

Claus, R. W.↗

NASA NTRS1981

Spectral flame radiance from a tubular-can combustor

An experimental investigation was conducted to determine the effects of fuel type, fuel-air ratio, and inlet-air pressure on the spectral flame radiance emanating from a JT8D can combustor. Spectral radiance measurements from 1.55 to 5.5 micrometers of wavelength were recorded and analyzed to determine soot concentration and flame temperature at various axial locations in the combustor. Two fuels differing in volatility, viscosity, and chemical composition were used in this investigation.

Claus, R. W.↗

NASA NTRS1979

Effect of primary-zone equivalence ratio on pollutant formation

Test were conducted to determine the effect of primary-zone equivalence ratio on the formation of smoke and other gaseous pollutants in an experimental can combustor. Several fuel injection techniques were examined at primary-zone equivalence ratios from 0.8 to 2.0. The main emphasis was on reducing fuel-rich-combustion smoke levels. Two of the four fuel injection configurations studied produced smoke levels below a smoke number of 20 at a primary-zone equivalence ratio of about 1.7. As the fuel mixing and atomization were recorded at primary-zone equivalence ratios as high as 2.0. The gaseous emissions of unburned hydrocarbons, carbon monoxide, and oxides of nitrogen were quite sensitive to the fuel injection configuration as well as to the primary-zone equilvalence ratio.

Claus, R. W.↗

NASA NTRS1979

Ceramic coating effect on liner metal temperatures of film-cooled annular combustor

An experimental and analytical investigation was conducted to determine the effect of a ceramic coating on the average metal temperatures of full annular, film cooled combustion chamber liner. The investigation was conducted at pressures from 0.50 to 0.062. At all test conditions, experimental results indicate that application of a ceramic coating will result in significantly lower wall temperatures. In a simplified heat transfer analysis, agreement between experimental and calculated liner temperatures was achieved. Simulated spalling of a small portion of the ceramic coating resulted in only small increases in liner temperature because of the thermal conduction of heat from the hotter, uncoated liner metal.

Claus, R. W.↗

NASA NTRS1978

The effect of ambient conditions on the emissions of an idling gas turbine

Changes in ambient conditions - pressure, temperature, and humidity - affect the exhaust emissions of a gas turbine engine. Such variations must be compensated for during engine certification. The results of a test program employing a JT8D-17 combustor are presented which quantize the effect of carefully controlled changes on unburned hydrocarbons, carbon monoxide, and oxides of nitrogen at simulated idle operating conditions. Analytical results are given to explain the observed hydrocarbon and carbon monoxide behavior. It is shown that for a complete range of possible ambient variations, significant changes do occur in the amount of pollutants emitted by an idling gas turbine.

Kauffman, C. W.↗