Engineering topics

Claus, R. O.

Publications and source records attributed to Claus, R. O..

48 records · Page 3

NASA NTRS1981

DC calibration of the strain sensitivity of a single mode optical fiber interferometer

The strain sensitivity of an optical fiber interferometer developed for the detection of pulsed ultrasonic waves in solids was calibrated. Light from the output ends of both fibers was superimposed to form an interference fringe pattern that was interrogated in the far field to give a signal proportional to the differential optical fiber path length. Strain sensitivity is determined by comparing data obtained by clamping and bending the bar at different lengths to simple cantilever beam theory. A minimum theoretical detectable strain of less than 10 to the minus 10th power is indicated.

Claus, R. O.↗

NASA NTRS1981

Detection of acoustic emission in composites by optical fiber interferometry

Acoustic emission in prestressed composite panels using embedded single mode optical fiber was detected. Static loading of the composite matrix produces acoustic emission events, pulsed ultrasonic waves, which mechanically modulate the embedded fiber geometry and phase modulate the transmitted optical field. The modulation is detected by optical interferometry and Fourier optical processing techniques to produce an electronic signal proportional to acoustic field amplitude integrated along the length of the fiber in the specimen. Static and dynamic calibration of the detection system is discussed and frequency domain characterization of the acoustic field interaction with the fiber is presented.

Wade, J. C.↗

NASA NTRS1981

Pulsed-echo interface wave characterization of bolted plates

Ultrasonic waves which propagate along the plane boundary separating two solid substrates were used to characterize aluminum and titanium plates adhesively bonded and bolted together. Wave pulses were used to produce interface waves between the aluminum and a Ti-6Al-4V titanium alloy bar by normal mode conversion. Interface wave reflections from bolt holes drilled through the interface were reconverted to surface wave pulses and detected by the same wedge by standard pulse-echo techniques. Time of flight measurements indicate that the reflected waves are a supersonic of longitudinal modes and circularly symmetric waves that propagate around the bolt hole.

Turner, T. M.↗

NASA NTRS1981

Attenuation of ultrasonic interface waves on metal-polymer-metal boundaries

The measured sensitivity of interface wave attenuation to defects near the bondline and to variations in the viscosity of the adhesive layer was compared with theoretical changes predicted by the Rokhin model. Differential interferometric optical measurements of interface wave attenuation due to defects near glass polymer metal boundaries are discussed. Pitch catch and pulse echo methods which use variable angle wedge transducers to generate and receive modified interface waves and to measure large bondline defects and adhesive viscosity are described.

Claus, R. O.↗

NASA NTRS1981

Characterization of metal-polymer boundaries using Stoneley and Leaky waves

Optical and acoustooptical techniques for bonded surface inspection and interface wave detection are discussed. Interface wave propagation models based on viscous, elastic, and viscoelastic mechanical properties are reviewed. Gross boundary anomalies such as large defects and localized disbond regions were measured using conventional high frequency pulse echo and pitch catch ultratechniques. Bond durabilty is estimated by comparing detected wave attenuation versus frequency as a function of prebond surface preparation with the experimental limit obtained for perfect welded contact. Sensitivity of interface acoustic field periodicity to both residual and dc applied stress at the boundary surface is observed as well as hysteresis due to viscoelastic polymeric behavior as the applied stress is cycled.

Claus, R. O.↗

NASA NTRS1981

Waves guided by a thin viscoelastic layer between elastic solids

The propagation of ultrasonic waves guided along a viscoelastic layer which separates two dissimilar elastic solid half spaces is described. For the limiting cases of rigid and soft bonding by a layer thin compared to acoustic wavelength, Stoneley and independent Rayleigh wave characteristic equations, respectively, result. For combinations of layer rigidity and wave length that correspond to guided wave propagation, external cyclic loading of the layer produces mechanical hysteresis and a resulting dynamic change in bond properties. Measurements of velocity hysteresis in an aluminum polymer adhesive aluminum system are described.

Claus, R. O.↗

NASA NTRS1981

An ultrasonic transducer with Gaussian radial velocity distribution

A transducer with a velocity profile which is Gaussian as a function of radius and independent of angle is described. In materials evaluation applications requiring the interrogation of modified far field patterns of an ultrasonic transducer, it is desirable to use a transducer which produces a beam with a Gaussian profile. A computer aided electrode design and calibrated three dimensional interferometric optical and ultrasonic measurements of the far field distribution are presented.

Zerwekh, P. S.↗

NASA NTRS1981

Optical detection of pulsed surface particle displacements

Zewekh, P. S.↗

NASA NTRS1981

Wideband optical measurements of ultrasonic pulses

Calibrated masurements of acoustic surface wave pulses by wide bandwidth differential interferometry are described. By interrogating the interference pattern formed by superimposing two optical beams reflected from the surface at slightly separated points, an output signal proportional to instantaneous surface particle displacement is obtained. Response to ideal propagating step function displacements is analyzed and measurements of gated pulses are described.

Claus, R. O.↗

NASA NTRS1981

Dual differential interferometer for measurements of broadband surface acoustic waves

A simple duel interferometer which uses two pairs of orthogonally polarized optical beams to measure both the amplitude and direction of propagation of broadband ultrasonic surface waves is described. Each pair of focused laser probe beams is used in a separate wideband differential interferometer to independently detect the component of surface wave motion along one direction on the surface. By combining the two output signals corresponding to both components, the two dimensional surface profile and its variation as a function of time is determined.

Turner, T. M.↗

NASA NTRS1981

Optical detection of pulsed surface particle displacements

The detection of acoustic surface wave pulses by a wideband differential interferometric laser technique which is insensitive to low frequency noise is described. System bandwidth is determined by the relationship between acoustic wavelength and the variable spacing between two laser probe beams focused on the solid surface which supports the waves. Theoretical sensitivity to surface displacement amplitude is equal to, or better than, that of other electrooptical techniques. Response to an ideal step function displacement is analyzed and experimental measurements of gated 2.5 MHz pulses generated on an aluminized pyrex plate are discussed. Potential application in the characterization of acoustic emission in composites is described.

Zerwekh, P. S.↗

NASA NTRS1981

DC calibration of the strain sensitivity of a single mode optical fiber interferometer

The strain sensitivity of an optical fiber interferometer developed for the detection of pulsed ultrasonic waves in solids has been calibrated. The optical paths in both signal and reference arms of the interferometer are through similar 2 m lengths of ITT-110 single mode fibers mode stripped by index matching at both ends and attached to opposite sides of a 30 cm plexiglas bar 0.3 cm thick. Light from the output ends of both fibers was superimposed to form an interference fringe pattern that was interrogated in the far field to give a signal proportional to the differential optical fiber path length. Strain sensitivity was determined by comparing data obtained by clamping and bending the bar at different lengths to simple cantilever beam theory. Calibration indicates a minimum theoretical detectable strain of less than 10 to the -10.

Claus, R. O.↗