Engineering topics

Clark, R. K.

Publications and source records attributed to Clark, R. K..

34 records · Page 2

NASA NTRS1983

Residual mechanical properties of Ti-6Al-4V after simulated Space Shuttle reentry

Oxidation and embrittlement are concerns in use of titanium foils for shielding advanced space transportation system vehicles during Earth reentry. Ti-6Al-4V in 0.003 in. and 0.035 in. thicknesses were exposed to multiple cycles of simulated space transportation system ascent/reentry conditions at temperatures ranging from 1000 F to 1200 F. Residual mechanical tests and metallurgical analyses were made on the specimens after exposure. Results show that tensile elongation is the mechanical property most affected by the reentry environment. Results are presented to show a comparison of residual properties of foil specimens from static oxidation exposure and cyclic oxidation exposure.

Clark, R. K.↗

NASA NTRS1983

Fixture for environmental exposure of structural materials under compression load

A device for stressing a deformable material specimen consists of top plate and a bottom plate sandwiching a guide cylinder. The specimen is positioned on the bottom plate and attached to a load piston. Force is applied through the top plate into the guide cylinder. Once the specimen is loaded, the stress is maintained by tightening tie bolt nuts.

Clark, R. K.↗

NASA NTRS1983

Effect of load introduction in compression testing of composite laminates

Compression testing of composite materials is affected by the manner in which the compressive load is introduced. Two such effects are studied in this paper: (a) the constrained edge effect, in which transverse expansion of the edges is prevented while the axial load is introduced, and (b) nonuniform gripping, as manifested by inplane bending of the test specimen. The principle of minimum complementary energy is used to develop an analytical model that quantifies these two effects upon the measured elastic properties of laminated composites. Numerical results are presented for selected high-strength graphite/epoxy composites.

Reiss, R.↗

NASA NTRS1982

Radiative properties of a nickel based superalloy: Inconel 617 - After simulated earth reentry

Experimental results are presented to show the effect of environmental simulation exposures of convective heating and of radiant heating on the spectral (1.0 to 14 micrometers) and total emittance of oxidized Inconel 617. Convective heating exposures were conducted in an arc heated supersonic wind tunnel using a wedge-shaped specimen configuration. Radiant tests were conducted in dry air at a flow velocity of several meters per second. Convective heating specimens were subjected to 8, 20 and 38 heating cycles of 15-minutes duration and radiant heating specimens were tested for 10, 20, 50 and 100 one-half hour heating cycles. Changes in radiative properties are discussed in terms of changes in composition and morphology resulting from the exposure tests. Total normal emittance did not significantly change from the statically oxidized condition after either type of exposure, and it remained above 0.80 at 1260K for all cases. Although spectral changes were observed on post exposure specimens at wavelengths less than 2.0 micrometers and greater than 15 micrometers, these changes have no influence on total emittance at 1260K.

Cunnington, G. R.↗

NASA NTRS1981

Environmental testing under load

Inexpensive fixture applies compression loads to specimens exposed to environment. Fixture handles relatively large specimens suitable for postexposure analysis of physical, chemical, and mechanical properties.

Clark, R. K.↗

NASA NTRS1981

Compression testing of graphite/epoxy composite materials

Three methods for compression testing coupons of filament-reinforced polymer-matrix composite materials are evaluated, to identify the sensitivity of the test techniques to laminate, specimen, and test parameters. A 'wedge-grip' compression fixture, a face-supported compression fixture, and an end-loaded coupon fixture are described. Specimens of 12.5-, 25-, and 50-mm widths, 8-, 16-, and 24-ply thicknesses, and of various fiber orientations were used to test the 'wedge-grip' compression fixture and the face-supported fixture; the end-loaded coupon fixture was tested using 16-ply specimens. Compressive strain-stress, strength, and modulus data obtained with the fixtures and evaluations showing the effects of all the test parameters are presented. One of the conclusions asserts that the 'wedge-grip' compression fixture provides good stress-strain data to failure for unidirectional and quasi-isotropic laminates.

Clark, R. K.↗

NASA NTRS1980

An assessment of the readiness of ablative materials for preflight application to the shuttle orbiter

The shuttle orbiter relies primarily on a reusable surface insulation (RSI) thermal protection system (TPS). The RSI is very efficient in its thermal performance; however, the RSI tile system has shown poor mechanical integrity. The state-of-the-art of the ablative TPS is reviewed, and an assessment made of the ablator's readiness for use on the shuttle orbiter. Unresolved technical issues with regard to the ablative TPS are identified. Short time, highly focused analytical and experimental programs were initiated to: (1) identify candidate ablation materials; (2) assess the data base for these materials; (3) evaluate the need and kind of waterproof coating; (4) calculate thermal and other stresses in an ablator tile; (5) identify an acceptable ablator/RSI tile joint filler; and (6) assess the sensitivity of the ablator to sequential heat pulses. Results from some of these programs are discussed.

Tompkins, S. S.↗

NASA NTRS1980

Effects of method of loading and specimen configuration on compressive strength of graphite/epoxy composite materials

Three test schemes were examined for testing graphite/epoxy (Narmco T300/5208) composite material specimens to failure in compression, including an adaptation of the IITRI "wedge grip" compression fixture, a face-supported-compression fixture, and an end-loaded-coupon fixture. The effects of specimen size, specimen support arrangement and method of load transfer on compressive behavior of graphite/epoxy were investigated. Compressive stress strain, strength, and modulus data obtained with the three fixtures are presented with evaluations showing the effects of all test parameters, including fiber orientation. The IITRI fixture has the potential to provide good stress/strain data to failure for unidirectional and quasi-isotropic laminates. The face supported fixture was found to be the most desirable for testing + or - 45 s laminates.

Clark, R. K.↗

NASA NTRS1979

Mechanical and thermophysical properties of graphite/polyimide composite materials

An on-going program to characterize advanced composites for up to 50,000 hours of exposure to simulated supersonic cruise environments is summarized. Results are presented for up to 25,000 hours of thermal exposure and 10,000 hours of flight simulation at temperatures up to 560K (550 F) with emphasis on HTS/710 graphite/polyimide composite material. Results to date indicate that the maximum use temperature for HTS/710 may be reduced to 505K (450 F) for long-time (1000 hours) application such as the supersonic transport. Preliminary thermophysical properties data for HTS/PMR15 graphite/polyimide were generated. These data include thermal conductivity, thermal expansion, and specific heat from 115K (-252 F) to 590K (600 F) and emittance at room temperature and 590K (600 F). The purpose in generating these data was to validate use of state-of-the-art property measurement methods for advanced graphite fiber reinforced resin matrix composites. Based on results to this point, thermal expansion measurements for composites are most difficult to perform. A high degree of caution in conducting thermal expansion tests and analyzing results is required to produce reliable data.

Rummler, D. R.↗

NASA NTRS1978

Emittance of TD-NiCr after simulated reentry

The effects of simulated reentry heating on the emittance of TD-NiCr were investigated. Groups of specimens with three different preconditioning treatments were exposed to 6, 24, and 30 half-hour simulated reentry exposure cycles in a supersonic arc tunnel at each of three conditions intended to produce surface temperatures of 1255, 1365, and 1475 K. Emittance was determined at 1300 K on specimens which were preconditioned only and specimens after completion of reentry simulation exposure. Oxide morphology and chemistry were studied by scanning electron microscopy and X-ray diffraction analysis. A consistent relationship was established between oxide morphology and total normal emittance. Specimens with coarser textured oxides tended to have lower emittances than specimens with finer textured oxides.

Clark, R. K.↗

NASA NTRS1973

An analysis of a charring ablator with thermal nonequilibrium, chemical kinetics, and mass transfer

The differential equations governing the transient response of a one-dimensional ablative thermal protection system are presented for thermal nonequilibrium between the pyrolysis gases and the char layer and with finite rate chemical reactions occurring. The system consists of three layers (the char layer, the uncharred layer, and an optical insulation layer) with concentrated heat sinks at the back surface and between the second and third layers. The equations are solved numerically by using a modified implicit finite difference scheme to obtain solutions for the thickness of the charred and uncharred layers, surface recession and pyrolysis rates, solid temperatures, porosity profiles, and profiles of pyrolysis-gas temperature, pressure, composition, and flow rate. Good agreement is obtained between numerical results and exact solutions for a number of simplified cases. The complete numerical analysis is used to obtain solutions for an ablative system subjected to a constant heating environment. Effects of thermal, chemical, and mass transfer processes are shown.

Clark, R. K.↗

NASA NTRS1972

A Numerical Analysis of the Transient Response of an Ablation System Including Effects of Thermal Nonequilibrium, Mass Transfer and Chemical Kinetics

The differential equations governing the transient response of a one-dimensional ablative thermal protection system undergoing stagnation ablation are derived. These equations are for thermal nonequilibrium effects between the pyrolysis gases and the char layer and kinetically controlled chemical reactions and mass transfer between the pyrolysis gases and the char layer. The boundary conditions are written for the particular case of stagnation heating with surface removal by oxidation or sublimation and pyrolysis of the uncharred layer occurring in a plane. The governing equations and boundary conditions are solved numerically using the modified implicit method (Crank-Nicolson method). Numerical results are compared with exact solutions for a number of simplified cases. The comparison is favorable in each instance.

Clark, R. K.↗

NASA NTRS1969