Engineering topics

Ciesielski, Peter (ORCID:0000000333609210)

Publications and source records attributed to Ciesielski, Peter (ORCID:0000000333609210).

4 records

DOE OSTI2025

Impacts of Biomass Feedstock Pre-Processing on Heat and Mass Transfer During Pyrolysis Using X-Ray Computed Tomography and Multiscale Modeling

Knowledge of the transport properties of biomass particles such as porosity, tortuosity, and permeability is paramount for high-fidelity modeling of biomass pyrolysis due to the heat and mass transfer limitations imposed by particle microstructure. X-ray computed tomography (XCT) is a non-destructive imaging method that enables full 3D reconstructions of the biomass particle microstructure with high resolution, permitting direct calculation of porosity, tortuosity, and permeability from real particle geometries. In this study, XCT imaging revealed the 3D microstructures of particles and chars from pyrolytic conversion of cylindrically cut or milled/pelletized loblolly pine samples. The porosity, tortuosity, and permeability were calculated directly from the XCT geometries via open-source microstructural analysis tool MATBOX+TauFactor (https://github.com/NREL/MATBOX_Microstructure_analysis_toolbox) and computational fluid dynamics (CFD) simulations using our solver, Mesoflow (https://github.com/NREL/mesoflow). These properties were used in a reactor scale model developed in COMSOL of the single particle reactor at NREL to investigate the impact of feedstock pre-processing on biomass conversion during pyrolysis with rigorous experimental validation.

biomass↗

DOE OSTI2025

Investigating the Effect of Water on the Mechanical Properties of Cellulose from Multiscale Molecular Dynamics Simulations

Classical molecular dynamics (MD) simulations provide insight into the structure and physicochemical properties of materials with atomic resolution. However, the length and time scales accessible to atomistic MD are orders of magnitude smaller than many relevant processes such as the response of a bulk material to experimentally accessible strain rates, which presents challenges when comparing models to experimental measurements. Bottom-up coarse-graining provides a means for systematically mapping atomistic information to lower resolution models to increase the length and time scales achievable by simulation. Cellulose is an abundant carbohydrate biopolymer with applications to many fields of research, such as materials science and renewable energy, due to its desirable mechanical properties and viability for conversion into biofuel. The effect of moisture content on the Young's modulus of cellulose is of special interest due to its native environment often being in the hydrated secondary plant cell wall and the grinding energy requirements for biomass feedstock preprocessing. The current work investigates the effects of water solvent on the Young's modulus of cellulose calculated from coarse-grained MD mechanical stress simulations. The coarse-grained model was parametrized from atomistic MD calculations of cellulose-cellulose potentials of mean force using umbrella sampling techniques under vacuum and solvated conditions. The Young's moduli of the coarse-grained cellulose assemblies parametrized from cellulose in vacuum or solvated in water were computed via mechanical stress simulations to highlight the importance of capturing solvent interactions for modeling the mechanical behavior of cellulose.

BASIC BIOLOGICAL SCIENCES,RADIATION PROTECTION AND↗

DOE OSTI2023

Simulating Catalysis with Realistic Pellet Geometries Using Mesoflow: A Case Study of Catalytic Propane Dehydrogenation

We present a case study of catalytic propane dehydrogenation with our open-source multiphysics solver, Mesoflow. The solver was developed to simulate reactive flow coupled to heterogeneous catalytic reactions and deactivation in the context of complex, mesoscale geometry. The method leverages cartesian block-structured adaptive mesh refinement to capture realistic catalyst microstructural features acquired directly from X-ray computed tomography data. A kinetic model for propane dehydrogenation and catalyst deactivation was developed based on temporal analysis of products (TAP) reactor experiments. The TAP reactor experiments allow for precise characterization of intrinsic kinetic reaction steps which are implemented into Mesoflow simulations to model the spatial and temporal evolution of reactants, products, and catalyst active sites. The short-term and long-term deactivation behavior is studied by using XCT data collected from fresh and aged catalyst pellets, which exhibit different microstructural features. This study employs time-splitting algorithms to connect disparate reaction and flow timescales, enabling the simulations to achieve realistic deactivation timescales on the order of minutes while the flow time-scales for small particles (100 microns) are several milliseconds. We also introduce a flexible automated python script that writes the necessary files to construct a Mesoflow simulation from user-created chemical mechanisms. We will also introduce a few new features that are added to Mesoflow such as higher order schemes, implicit chemistry integrators and the ability to run on AMD and NVIDIA graphics-processing-units.

AMReX↗

DOE OSTI2023

Amino Acids Essential for the Assembly of Cellulose Synthase Complexes

Over 40 years ago, Andrew Staehelin's group showed that plant cellulose microfibrils are synthesized by protein complexes arranged in hexagonal arrays called 'particle rosettes'. Plant cellulose synthases (CESAs) differ from their bacterial ancestral forms by insertion of three unique sequences responsible for the assembly into compact multimeric units that aggregate further into rosettes. We used site-directed mutagenesis to replace amino acids within these sequences predicted to be essential for assembly and developed an in vivo method to determine the ability of mutated CesA1 transgenes to complement an Arabidopsis temperature-sensitive root-swelling1 (rsw1) mutant. Replacement of a Cys residue in the Class-Specific Region (CSR) or Pro417 and Arg453 of the Plant-Conserved Region (P-CR) rendered an AtCesA1 transgene unable to complement the rsw1 mutation. Despite an expected role for Arg457 in the trimerization of CESA proteins, AtCesA1 transgenes with Arg457Ala mutations were able to fully restore the wild-type phenotype in rsw1. Staehelin observed a third order of assembly in Micrasterias dendiculata, where hundreds of rosettes form large hexagonal arrays during the synthesis of secondary wall cellulose macrofibrils. We found by SEM of cytosolic faces of Micrasterias cell fragments that these arrays are associated with fields of regularly spaced slime secretion pore complexes.

arabidopsis↗