Engineering topics

Chowdhury, Dhruba

Publications and source records attributed to Chowdhury, Dhruba.

4 records

DOE OSTI2024

Thermal images collected during large-scale 3D printing with Ingersoll MasterPrint

This data set contains images produced to test the performance of anomaly and fault detection methods in the context of additive manufacturing. Two print jobs were executed using the Ingersoll MasterPrint with the Model 30 Strangpresse extruder. The material used was Techmer compounded polylactic acid (PLA) with wood flour as a filler (80/20 PLA/WF by weight). The first print job consists of the 3D printing of a hexagonal cylinder with a two-bead wall. This print was sliced at a gantry velocity of 3000 millimeter per minute, and an extruder screw speed of 68.14 rotations per minute. This are considered the normal operating conditions. A second hexagonal cylinder was printed using a reduced extruder screw speed, 15% lower than under normal operating conditions. The images were collected with a Teledyne FLIR Lepton 3.5 infra-red camera, a small form factor radiometric long-wave infrared camera with a spectral range of 8 µm to 14 µm. Sensor resolution was 160x120 pixels, with a pixel size of 12 µm, a temperature range of -10 - 450°C, and an accuracy of +/- 10°C in its low gain configuration. Images in this data set were collected with cameras oriented at the printer nozzle. The nozzle camera setup consisted of two cameras located 12.5cm from the nozzle center. These were mounted directly to the print head, so that the camera positions relative to the print direction would remain constant as it rotated around its C-axis to follow the print path. One camera was placed ahead of the nozzle to capture the previous layer immediately before being covered by the new layer of material, while the second camera was placed behind the nozzle and captured the freshly extruded bead. Images are collecting during each phase of the print: (a) idle (i.e., no material deposited), (b) extrusion (i.e., to prime the extruder), and (c) printing (deposition of material to manufacture the hexagonal cylinder).

36 MATERIALS SCIENCE↗

DOE OSTI2022

Black-box optimization of a closed-circuit reverse osmosis system for desalination through extremum seeking control

We study the minimization of the cost function of a closed-circuit desalination reverse osmosis (CCRO) system, which is used for producing drinking water. The cost function is a trade-off between the specific energy consumption and the specific brine management cost. The extremum-seeking controller (ESC) manipulates the critical electric conductivity of the brine to minimize the cost function. Experiments were designed in which the composition of the feed salinity is increased to test the controller’s ability to converge to a new optimum. The ESC was able to shift the critical conductivity to a new optimum, which resulted in a 9% improvement in the cost function.

Chowdhury, Dhruba↗

DOE OSTI2022

Method for automatic correction of offset drift in online sensors

Abstract Successful operation and optimization of water treatment systems hinge on the availability of high-quality online sensor measurements. Ideally, the available measurements should be simultaneously accurate (i.e., unbiased and precise), representative, voluminous, and timely. This remains a pain-point in current water infrastructures, forming a barrier to a wider adoption of advanced and autonomous control systems. While short-lived symptoms, such as outliers and spikes, can be detected or corrected with state-of-the-art tools for fault detection and identification, it is much more difficult to detect, diagnose, and correct the symptoms of slow faults, such as changes in offset or sensitivity due to drift. The time scale of drift is often longer than the time scales of the system dynamics of interest. Moreover, sensor drift has been shown to occur at the same time and with similar rates when sensors are exposed to the same conditions. This challenges data quality management strategies based on redundancy. In this contribution, we develop a new method, including both a hands-off sensor calibration mechanism and an information-seeking control architecture that can handle the unique challenge of simultaneous and similar drift in online sensors.

Chowdhury, Dhrubajit↗

DOE OSTI2021

Automatic Drift Correction through Nonlinear Sensing

For successful design and operation of advanced monitoring and control systems, engineers rely on high quality sensor signals that are simultaneously accurate, representative, voluminous, and timely. Unfortunately, sensor faults are common and lead to short-lived symptoms, such as outliers and spikes as well as long-lived symptoms, such as sensor drift. Sensor drift belongs to the category of incipient faults. These are particularly challenging to detect, diagnose, and correct as the time scales of these faults are typically longer than the time scales of the system dynamics that are of interest. Moreover, if sensor drift occurs as a result of exposure to measured medium, then it is likely that multiple sensors will exhibit similar drift rates, thus challenging fault management strategies based on redundancy. In this contribution, we present a first method that can handle this unique challenge.

Chowdhury, Dhruba↗