Engineering topics
Publications and source records attributed to Chow, Chuen-Yen.
Numerical-simulation method for aeroelasticity analysis of helicopter rotor blade combines established techniques for analysis of aerodynamics and vibrations of blade. Application of method clearly shows elasticity of blade modifies flow and, consequently, aerodynamic loads on blade.
Compressible stability equations are solved using the spectral collocation method in an attempt to study the effects of temperature difference and compressibility on the stability of Taylor-Couette flow. It is found that the Chebyshev collocation spectral method yields highly accurate results using fewer grid points for solving stability problems. Comparisons are made between the result obtained by assuming small Mach number with a uniform temperature distribution and that based on fully incompressible analysis.
A computational fluid dynamics (CFD) method is used to study the aerodynamics of the YAV-8B Harrier II wing in the transonic region. A numerical procedure is developed to compute the flow field around the complicated wing-pylon-fairing geometry. The surface definition of the wing and pylons were obtained from direct measurement using theodolite triangulation. A thin-layer Navier-Stokes code with the Chimera technique is used to compute flow solutions. The computed pressure distributions at several span stations are compared with flight test data and show good agreement. Computed results are correlated with flight test data that show the flow is severely separated in the vicinity of the wing-pylon junction. Analysis shows that shock waves are induced by pylon swaybrace fairings, that the flow separation is much stronger at the outboard pylon and that the separation is caused mainly by the crossflow passing the geometry of wing-pylon junction.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
In a microgravity environment, a hollow cylinder of fluid is unstable to axisymmetric disturbances and breaks up to form hollow spheres. These instabilities are due to the surface tension of the fluid. The linear stability analysis presented in this paper shows that the viscosity of the fluid reduces the instability of the configuration, but that, regardless of its magnitude, it can never completely eliminate the instability.
Explore the source record for details and available documents.
CNS, a new computational fluid dynamics procedure, has been developed to aid in hypersonic vehicle design. The code can be used to model the entire external flow around hypersonic vehicle shapes, from the captured shock at the nose to the beginning of the wake. Unlike space-marching codes, the technique allows axially separated flow regions to be modeled. Validation trials using sphere-cone data reveal good solution accuracy for the surface pressure and flowfield temperature.
A numerical method is presented for calculating the unsteady transonic rotor flow with aeroelasticity effects. The blade structural dynamic equations based on beam theory were formulated by FEM and were solved in the time domain, instead of the frequency domain. For different combinations of precone, droop, and pitch, the correlations are very good in the first three flapping modes and the first twisting mode. However, the predicted frequencies are too high for the first lagging mode at high rotational speeds. This new structure code has been coupled into a transonic rotor flow code, TFAR2, to demonstrate the capability of treating elastic blades in transonic rotor flow calculations. The flow fields for a model-scale rotor in both hover and forward flight are calculated. Results show that the blade elasticity significantly affects the flow characteristics in forward flight.
While the zonal grid system of Transonic Navier-Stokes (TNS) provides excellent modeling of complex geometries, improved shock capturing, and a higher Mach number range will be required if flows about hypersonic aircraft are to be modeled accurately. A computational fluid dynamics (CFD) code, the Compressible Navier-Stokes (CNS), is under development to combine the required high Mach number capability with the existing TNS geometry capability. One of several candidate flow solvers for inclusion in the CNS is that of F3D. This upwinding flow solver promises improved shock capturing, and more accurate hypersonic solutions overall, compared to the solver currently used in TNS.
The viscous effects on transonic flow past an airfoil which contains a shallow cavity beneath a porous surface are studied numerically. The porous region occupies a small portion of the total airfoil surface, and is located near the shock. Both an interactive boundary layer (IBL) algorithm and a thin-layer Navier-Stokes (TLNS) algorithm have been modified for use in studying the outer flow, whereas a stream-function formulation has been used to model the inner flow in the small cavity. The coupling procedure at the porous surface is based on Darcy's law and on the assumption of a constant total presusre in the cavity. In addition, a modified Baldwin-Lomax turbulence model is used to consider the transpired turbulent boundary layer in the TLNS approach, and the Cebeci-Smith turbulence model is used in the IBL approach. According to the present analysis, a porous surface can reduce the wave drag appreciably, but it can also increase viscous losses. As has been observed experimentally, the numerical results indicate that the total drag is reduced at higher Mach numbers and increased at lower Mach numbers when the angles of attack are small. Furthermore, the streamline patterns of passive-shock and boundary-layer interaction are revealed in this study.