Engineering Papers⌕ Search

Engineering topics

Chmielus, Markus

Publications and source records attributed to Chmielus, Markus.

Binder Jet-Metals

Additive manufacturing is a type of material shaping technology that has many advantages over traditional manufacturing. Binder jet additive manufacturing uses a powder feedstock and an inkjet printhead to shape metal powders into preforms that are then processed in a furnace to reach full density. Because of the high throughput and low cost of the process, binder jetting is growing in popularity among manufacturers, but challenges with the process in terms of densification of the bound preforms still exist. This article will provide an overview of the binder jetting process, contrast binder jetting with the better-known powder bed fusion additive manufacturing technologies, review the metal alloys that have been printed with binder jet and then processed to full density, and provide a path forward for processing lightweight metal powders shaped by binder jetting to full density.

Elliott, Amy↗

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

The thermal history developed in laser powder bed fusion (LPBF) processes has been shown to be complex resulting in equally complex microstructures and mechanical properties. Microscopic observations and Vickers micro-hardness mapping measurements were carried out on diff ;erent section planes of LPBF alloy 718 cuboids. Three-dimensional finite element analysis was used to simulate thermal history and to predict the residual stress distribution in the as-built material. Computational thermodynamics was used to predict the micro-segregation and nucleation driving force of various phases in the bulk and in segregated regions. Varied heat-treatments such as simulated hot isostatic pressing, and double aging were applied. Their influence on the microstructure, microsegregation, precipitate formation, and micro-hardness variations of LPBF alloy 718 were investigated. Hardness map results showed heterogeneous micro-hardness on the xy- and xz-planes of the as-built parts where the bottom plane and center regions had larger hardness of ~315 HV 0.5 while the top plane and contours showed hardness of ~300 HV 0.5 . It was found that the aging treatment increased the overall hardness of the as-built condition from ~310 HV 0.5 to 470 HV 0.5 but also increased the hardness gradient throughout the coupon. After simulated hot isostatic pressing process (i.e., without applied pressure) at 1020 °C for 4 h followed by water quench (HIPWQ), the hardness gradient and hardness was minimized (~210 HV 0.5 ) as the microstructure transitioned from heterogeneous columnar grains in the as-built condition to more uniform recrystallized grains. A double aging treatment was applied to enhance hardness from ~210 HV 0.5 to ~440 HV 0.5 . Finally, HIPWQ followed by double aging produced a homogeneous microstructure and more uniform hardness map with enhanced mechanical properties in LPBF alloy 718 coupons.

36 MATERIALS SCIENCE↗

Comparison of characterization methods for differently atomized nickel-based alloy 625 powders

The deployment of additive manufacturing depends on the quality of the produced part, specifically the absence of internal defects, impurities and compositional gradient. In this paper, differently atomized nickel-based alloy 625 powder particles were systematically characterized with different methods and results were compared. Powder properties were studied to understand the effect of different atomization methods on the properties of the powder particles. Morphology, shape and size of water and argon atomized powders were observed using optical microscopy, scanning electron microscopy and micro-computed X-ray tomography (μCT); μCT with different resolution and sample setup. As expected, water atomized powder particles have irregular morphology in contrast to spherical gas atomized particles. Phase and elemental analysis were conducted with X-ray diffraction and energy dispersive spectroscopy; thermal properties were measured with differential scanning calorimetry. Gas atomized powder shows composition and melting temperature close to nominal bulk alloy 625. Particle size analysis was carried out using sieving, laser particle size analysis and μCT. It is found that the average particle size obtained from μCT depends on scan resolution. Additionally, porosity of the powders was observed in SEM micrographs and investigated in detail using μCT. In conclusion, μCT with higher resolution results in collecting accurate shape, size, porosity and morphology of the powder particles. Finally, considering the large number of particles that can be investigated with μCT and ability to observe internal porosity, μCT is found to be an appropriate if not superior substitution for other powder characterization methods such as optical/electron microscopies, sieving and laser particle size analysis if time of characterization is not a concern.

36 MATERIALS SCIENCE↗

Characterization of oxide scales grown on alloy 310S stainless steel after long term exposure to supercritical water at 500 °C

The oxide scale grown of static capsules made of alloy 310S stainless steel was investigated by exposure to the supercritical water at 500 °C 25 MPa for various exposure times up to 20,000 h. Characterization techniques such as X-ray diffraction, scanning/transmission electron microscopy, energy dispersive spectroscopy, and fast Fourier transformation were employed on the oxide scales. The elemental and phase analyses indicated that long term exposure to the SCW resulted in the formation of scales identified as Fe{sub 3}O{sub 4} (outer layer), Fe-Cr spinel (inner layer), Cr{sub 2}O{sub 3} (transition layer) on the substrate, and Ni-enrichment (chrome depleted region) in the alloy 310S. It was found that the layer thickness and weight gain vs. exposure time followed parabolic law. The oxidation mechanism and scales grown on the alloy 310S stainless steel exposed to SCW are discussed. - Highlights: •Oxidation of alloy 310S stainless steel exposed to SCW (500 °C/25 MPa) •The layer thickness and weight gain vs. exposure time followed parabolic law. •Oxide layers including Fe{sub 3}O{sub 4} (outer), Fe-Cr spinel (inner) and Cr{sub 2}O{sub 3} (transition) •Ni element is segregated by the selective oxidation of Cr.

36 MATERIALS SCIENCE↗