Engineering Papers⌕ Search

Engineering topics

Chipman, R.

Publications and source records attributed to Chipman, R..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

SWIRP (Submm-Wave and Long Wave InfraRed Polarimeter); Development and Characterization of a Sub-Mm Polarimeter for Ice Cloud Investigations

A major source of uncertainty in climate models is the presence, shape and distribution of ice particles in the uppermost layers of the clouds. The effects of this component are poorly constrained, turning ice particles into an almost-free variable in many climate models.NASA-GSFC is developing a new instrument aimed at measuring the size and shape of ice particles. The instrument consists of two sub-mm polarimeters (at 220 and 670 GHz) coupled with a long-wave infrared polarimeter at 10 micron. Each polarimeter has identical V-pol and H-pol channels; the axes of polarization are defined geometrically by the orientation of the waveguide elements, and the purity has been measured in the lab. The instrument is configured as a conical scanner, suitable for deployment as a payload on a small satellite or on a high-altitude sub-orbital platform. From a 400 km orbit, the instrument has a 3dB spatial resolution of 20 (10) km at 220 (670) GHz and a swath of 600 km over 180 degrees of view.The BAPTA (Bearing And Power Transfer Assembly) carries heritage from the SSMIS design, now in its 22nd year of on-orbit operation, but with a much reduced SWaP (Size Weight and Power) footprint, suitable for a small satellite.The main components of the instrument have been fabricated and are undergoing final testing prior to their integration as a single unit. The sub-mm channels have dedicated secondary reflectors which illuminate a shared primary reflector. The receiving units are placed behind the focal point of the optical arrangement, so that all beams equally illuminate the primary reflector and are almost co-located on the ground (within a single 220 GHz footprint). Primary and secondary beam patterns have been measured and verified to match the as-designed expectations. A Zytex (TM) window is deployed to protect the secondary reflectors and the feed horns from debris and other contaminants, and to reduce the heat load from the active (hot) IR calibration unit. The insertion loss of Zytex has been measured and is accounted in the calibration equation of the sub-mm channels.The radiometric performance of the sub-mm receivers has been characterized in the lab and under operational conditions of temperature and pressure.This paper discusses the design constraints on the sub-mm components, details of the scientific goals and their flowdown, and describes the characterization of the polarimeters. Options to optimize the layout and distribution of the masses within the assembly, with the goal of making the instrument even more compact and fully-compatible with cubesat-class satellites will be presented.

De Amici, G.↗
NASA NTRS1985

Transonic test of a forward swept wing configuration exhibiting Body Freedom Flutter

The aeroelastic dynamic instability designated Body Freedom Flutter (BFF) involves aircraft pitch and wing bending motions characteristic of forward swept wing (FSW) aircraft. Attention is presently given to the results of tests conducted on a 1/2-scale cable-mounted FSW wind tunnel model, with and without relaxed static stability (RSS) control conditions. BFF instability boundaries were found to occur at significantly lower air speeds than those associated with aeroelastic wing divergence on the same model. Servoaeroelastic stability analyses have been conducted which proved capable of predicting the measured onset of BFF, in both the statically stable and RSS configurations tested.

Chipman, R.↗
NASA NTRS1984

Body-freedom flutter of a 1/2-scale forward-swept-wing model, an experimental and analytical study

The aeroelastic phenomenon known as body-freedom flutter (BFF), a dynamic instability involving aircraft-pitch and wing-bending motions which, though rarely experienced on conventional vehicles, is characteristic of forward swept wing (FSW) aircraft was investigated. Testing was conducted in the Langley transonic dynamics tunnel on a flying, cable-mounted, 1/2-scale model of a FSW configuration with and without relaxed static stability (RSS). The BFF instability boundaries were found to occur at significantly lower airspeeds than those associated with aeroelastic wing divergence on the same model. For those cases with RSS, a canard-based stability augmentation system (SAS) was incorporated in the model. This SAS was designed using aerodynamic data measured during a preliminary tunnel test in which the model was attached to a force balance. Data from the subsequent flutter test indicated that BFF speed was not dependent on open-loop static margin but, rather, on the equivalent closed-loop dynamics provided by the SAS. Servo-aeroelastic stability analyses of the flying model were performed using a computer code known as SEAL and predicted the onset of BFF reasonably well.

Chipman, R.↗
NASA NTRS1984

Control of forward swept wing configurations dominated by flight-dynamic/aeroelastic interactions

An active control system concept for an aeroelastic wind-tunnel model of a statically unstable FSW configuration with wing-mounted stores is developed to provide acceptable longitudinal flying qualities while maintaining adequate flutter speed margin. On FSW configurations, the inherent aeroelastic wing divergence tendency causes strong flight-dynamic/aeroelastic interactions that in certain cases can produce a dynamic instability known as body-freedom flutter (BFF). The carriage of wing-mounted stores is shown to severely aggravate this problem. The control system developed combines a canard-based SAS with an Active Divergence/Flutter Suppression (ADFS) system which relies on wing-mounted sensors and a trailing-edge device (flaperon). Synergism between these two systems is exploited to obtain the flying qualities and flutter speed objectives.

Rimer, M.↗
NASA NTRS1982

Algorithm for Unsteady Potential Flow About Airfoils

Implicit finite-difference scheme efficiently computes unsteady potential flow about airfoils. Formulation uses density and velocity potential as dependent variables. Conservation form is retained to assure that shock wave location and speed are computed correctly. Scheme fills need for method to calculate efficiently unsteady potential flow about airfoils and to predict flutter and other unsteady aeroelastic phenomena in transonic flow regimes.

Chipman, R.↗
NASA NTRS1981

An alternating-direction implicit algorithm for unsteady potential flow

An implicit finite-difference scheme is presented for the efficient computation of unsteady potential flow about airfoils. The formulation uses density and the velocity potential as dependent variables and is cast in conservation form to assure the theoretically correct determination of shockwave location and speed. To enable boundary conditions to be imposed directly on the airfoil surface, a time-varying sheared-rectilinear coordinate transformation is employed. Calculated time-history solutions on a pulsating airfoil are compared with the results of other unsteady transonic codes, including a previous method of the authors. The present method is demonstrated to be unconditionally stable and to give accurate solutions with sharply resolved shocks.

Chipman, R.↗
NASA NTRS1979

Numerical computation of aeroelastically corrected transonic loads

A numerical scheme is presented for the computation of transonic aerodynamic loads on flexible wings. The method consists of iteratively applying the loads computed by a 3D transonic aerodynamics code to a structural model to obtain elastic twist, and then recomputing the loads. Because this iteration is performed concurrently with the iterations performed in computing the aerodynamics, flexible loads are obtained in roughly the same amount of computing time as required to obtain rigid loads. Applications of this method to a flexible supercritical transonic transport wing are presented and compared with model test data.

Chipman, R.↗
NASA NTRS1977

Technical assistance and the transfer of remote sensing technology

The transfer of technology from industrialized countries to the third world is a very complicated process and one that requires a great deal of research and development. The political and social obstacles to this transfer are generally greater than the technical obstacles, but technical assistance programs have neither the competence nor the inclination to deal with these factors adequately. Funding for technical assistance in remote sensing is now expanding rapidly, and there is a growing need for institutions to study and promote the effective use of this technology for economic development. The United Nations, the Food and Agriculture Organization, the World Bank, the United States Agency for International Development and the Canadian technical assistance agencies take different approaches to the problem and deal with the political pressures in different ways.

Chipman, R.↗