Engineering Papers⌕ Search

Engineering topics

Chiang, YM

Publications and source records attributed to Chiang, YM.

Improving the Capacity of Sodium Ion Battery Using a Virus-Templated Nanostructured Composite Cathode

In this work we investigated an energy-efficient biotemplated route to synthesize nanostructured FePO4 for sodium-based batteries. Self-assembled M13 viruses and single wall carbon nanotubes (SWCNTs) have been used as a template to grow amorphous FePO4 nanoparticles at room temperature (the active composite is denoted as Bio-FePO4-CNT) to enhance the electronic conductivity of the active material. Preliminary tests demonstrate a discharge capacity as high as 166 mAh/g at C/10 rate, corresponding to composition Na0.9FePO4, which along with higher C-rate tests show this material to have the highest capacity and power performance reported for amorphous FePO4 electrodes to date.

Moradi, M↗

Electroactive-Zone Extension in Flow-Battery Stacks

Flowable suspensions that conduct both electrons and ions can enable the use of energy-dense electroactive species in flow batteries [M. Duduta et al., Adv. Energy Mater., 1, 511 (2011); Z. Li et al., Phys. Chem. Chem. Phys., 15, 15,833 (2013); F. Fan et al., Nano Lett., 14, 2210 (2014)]. In comparison with conventional flow batteries where electrochemical reactions are confined to a fixed current-collector region, electronically conductive flow electrodes permit electrochemical reactions to extend outside of the physical confines of the stack. We have measured and modeled how mixed-conduction enables an electroactive zone (EAZ, in which electrochemical reactions occur) that is of greater spatial extent than current collectors, the extension being termed side zone, SZ. Electrochemical reactions in SZs can reduce coulombic and energetic efficiency. Here we show that for realistic suspension properties and operating conditions, the added inefficiency is small in practice, and can be further mitigated by using appropriate operating conditions and/or materials choices. For the specific example of a non-aqueous Li4Ti5O12 suspension, we show that EAZ extension contributes less than 1% additional efficiency loss at C/10 rates for current collectors greater than 20 mm long. (C) 2014 Elsevier Ltd. All rights reserved.

Smith, KC↗

Aqueous semi-solid flow cell: demonstration and analysis

An aqueous Li-ion flow cell using suspension-based flow electrodes based on the LiTi2(PO4)(3)-LiFePO4 couple is demonstrated. Unlike conventional flow batteries, the semi-solid approach utilizes fluid electrodes that are electronically conductive. A model of simultaneous advection and electrochemical transport is developed and used to separate flow-induced losses from those due to underlying side reactions. The importance of plug flow to achieving high energy efficiency in flow batteries utilizing highly non-Newtonian flow electrodes is emphasized.

Li, Z↗

Modeling the hydrodynamic and electrochemical efficiency of semi-solid flow batteries

A mathematical model of flow cell operation incorporating hydrodynamic and electrochemical effects in three dimensions is developed. The model and resulting simulations apply to recently demonstrated high energy-density semi-solid flow cells. In particular, state of charge gradients that develop during low flow rate operation and their effects on the spatial non-uniformity of current density within flow cells are quantified. A one-dimensional scaling model is also developed and compared to the full three-dimensional simulation. The models are used to demonstrate the impact of the choice of electrochemical couple on flow cell performance. For semi-solid flow electrodes, which can use solid active materials with a wide variety of voltage-capacity responses, we find that cell efficiency is maximized for electrochemical couples that have a relatively flat voltage vs. capacity curve, operated under slow flow conditions. For example, in flow electrodes limited by macroscopic charge transport, an LiFePO4-based system requires one-third the polarization to reach the same cycling rate as an LiCoO2-based system, all else being equal. Our conclusions are generally applicable to high energy density flow battery systems, in which flow rates can be comparatively low for a given required power. (C) 2012 Elsevier Ltd. All rights reserved.

Brunini, VE↗