Engineering Papers⌕ Search

Engineering topics

Chen, Xiang

Publications and source records attributed to Chen, Xiang.

At least 73 records · Page 4

Technological aspects in blanket design: Effects of micro-alloying and thermo-mechanical treatments of EUROFER97 type steels after neutron irradiation

Presently available data on neutron irradiation damage raise doubts on the feasibility of using EUROFER97 steel for a water-cooled starter blanket in a DEMO reactor, since the ductile-to-brittle transition temperature (DBTT) increases significantly for irradiation temperatures below 350°C. The additional DBTT shift caused by H and He transmutation can only be estimated based on very few results with isotopically tailored EUROFER97 steel. Conservative calculations show that the DBTT of EUROFER97 steel could exceed the operating temperature in water-cooled starter blankets within a relatively short time period. This paper presents results from a EUROfusion funded irradiation campaign that was performed in the High Flux Isotope Reactor at Oak Ridge National Laboratory. The paper compares ten newly developed reduced activation ferritic-martensitic (RAFM) steels irradiated to a nominal dose of 2.5 dpa at 300°C. The post-irradiation experiments using Small Specimen Test Technology included hardness, tensile, and fracture mechanics tests combined with fractography and microstructure analysis are presented. Results show that micro-alloying EUROFER97-type steels influenced the mechanical properties but a dominating impact on irradiation damage resistance could not be identified. In contrast, specific thermo-mechanical treatments lead to better DBTT behavior. Discussion about irradiation response to heat treatment conditions is also given. Here, despite requiring data also at high dpa values, the results indicate that with these modified materials an increased lifetime and potentially also an increased operating temperature window can be achieved compared to EUROFER97.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Long-Term Creep-Rupture Behavior of Alloy Inconel 740/740H

To explore potential application of Ni-based alloys for power generation at the higher temperatures and pressures needed to achieve high thermal to electrical-energy conversion efficiency, an extensive creep-rupture dataset covering up to 875 °C and almost 70,000 h for Inconel 740/740H was analyzed using Larson–Miller parameter and Wilshire approaches. The results were used to assess the relative effectiveness of the two analytical methods, both in describing the experimental data and, because of the breadth of the dataset, using analyses of its shorter-time data to make creep lifetime predictions for much more extended times, which were then directly compared to the measured rupture times. The respective methods were also used to predict creep-limited lifetimes relevant to power production (that is, 100,000 h or greater). Despite the complexity of the precipitation-strengthened Inconel 740/740H alloy and the generalized parametric approach of these methodologies, the predictions based on such were reasonably accurate when the entire dataset was analyzed. However, when the analysis was confined to only data for conditions yielding creep-rupture times < 5,000 h( about 65 % of the entire dataset), the Wilshire correlation yielded better prediction for longer time lifetimes due to the inherent instability of the specific Larson–Miller formalism used in this analysis when extrapolated significantly outside its analysis range.

36 MATERIALS SCIENCE↗

Reanalysis of Cost and Moist Air Oxidation Performance for CF8C-Plus and Other Alloys for AUSC Applications

This report provides an economic analysis of CF8C-Plus and other candidate materials for Advanced Ultra Supercritical (AUSC) applications, including 347HFG, HR6W, Sanicro 25, Super 304H, Grade 92, SAVE12AD, Inconel 617, and Inconel 740H. An assessment of their moist air oxidation performance is also included. When compared with the aforementioned alloys, CF8C-Plus shows a favorable balance between cost, creep strength and moist air oxidation resistance in the temperature range of 600-700°C. Furthermore, its castability makes it additionally attractive from a manufacturing perspective. Materials with higher Ni content, such as HR6W, Sanicro 25, Inconel 617, and Inconel 740H, have better creep strength but the improved performance comes with increased cost. Stainless steel 347HFG exhibits inferior creep strength and lower moist air oxidation resistance, but at a greater cost, compared with CF8C-Plus. Super 304H, another stainless steel, has similar creep strength and cost compared to CF8CPlus at 700°C, but may not have as good moist air oxidation resistance. Grade 92 has lower creep strength and unfavorable economy compared with CF8C-Plus. SAVE12AD also has lower creep strength than CF8C-Plus, but has lower cost to use at 600°C. Both Grade 92 and SAVE12AD are also limited to the maximum use temperature of 649°C per ASME code case requirements.

36 MATERIALS SCIENCE↗

Short-Range Nematic Fluctuations in Sr 1-x Na x Fe 2 As 2 Superconductors

Interactions between nematic fluctuations, magnetic order and superconductivity are central to the physics of iron-based superconductors. Here we report on in-plane transverse acoustic phonons in hole-doped Sr 1-x Na x Fe 2 As 2 measured via inelastic x-ray scattering, and extract both the nematic susceptibility and the nematic correlation length. By a self-contained method of analysis, for the underdoped (x = 0.36) sample, which harbors a magnetically ordered tetragonal phase, we find it hosts a short nematic correlation length ξ ~ 10Å and a large nematic susceptibility Χ nem . The optimal-doped (x = 0.55) sample exhibits weaker phonon softening effects, indicative of both reduced xi and Χ nem . Overall, our results suggest short-range nematic fluctuations may favor superconductivity, placing emphasis on the nematic correlation length for understanding the iron-based superconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Precipitation behavior near shrinkage porosity in a large sand casting of Haynes 282 alloy

The precipitation behavior of L1 2 structure Ni 3 (Al,Ti)-type γ' precipitates near shrinkage porosity in a large sand casting of Haynes 282 alloy has been investigated by scanning/transmission electron microscopy in conjunction with energy dispersive x-ray spectroscopy. The experimental results revealed that in the carbonitride-rich region close to the shrinkage porosity, γ' precipitates could still form with comparable sizes though at lower volume density than those in the general cast Ni matrix. The resulting γ' precipitates had a very high Al/Ti ratio. Close to oxide-rich pore surfaces, an absence of γ' precipitates was observed due to Al and Ti depletion by forming Al oxides and Ti carbonitrides, respectively. This work suggests that Al rather than Ti plays a dominant role in the formation of γ' precipitates in porous regions in cast Haynes 282 alloys.

36 MATERIALS SCIENCE↗

Mechanical behavior of additively manufactured and wrought 316L stainless steels before and after neutron irradiation

Fabrication of nuclear reactor components using additive manufacturing (AM) methods is now a practical option since the AM technologies have advanced to allow for building of complex parts with high quality materials. To assess the mechanical performance of printed components in reactor-relevant conditions and to build a property database for the AM 316L stainless steel (SS), mechanical testing and characterization were performed before and after neutron irradiation. In this work, miniature tensile specimens were irradiated at the High Flux Isotope Reactor (HFIR) to 0.2 and 2 displacements per atom (dpa) at 300 and 600°C. The AM 316L SS was tested in the as-built, stress-relieved, and solution-annealed conditions, and the wrought (WT) 316L SS in solution-annealed condition as a reference alloy. The baseline test result showed that the AM 316L SS, regardless of the post-build heat treatment, had higher strength than the WT 316L SS, but similar ductility. Post-irradiation tensile testing was conducted at RT, 300°C, and 500°C for selected irradiation conditions. Neutron irradiation induced significant changes in the mechanical behavior of the AM stainless steels, including both hardening and softening. Although the as-built 316L steel after 300°C irradiation showed necking just after yielding, the overall property changes of the as-printed alloy became less significant after 600°C irradiation. Irradiation-induced ductilization was also observed after the higher temperature irradiation. In general, the strength change was smaller in the relatively stronger as-built and stress-relieved AM SSs than in the solution-annealed AM and WT SSs. These relatively lower strength 316L SSs overall retained higher ductility in the irradiation conditions tested, but the stronger 316L SSs demonstrated a similar level of ductility after the higher temperature (600°C) irradiation. It is a positive assessment for the AM 316L materials that no embrittlement was observed within the test and irradiation conditions of the experiment.

36 MATERIALS SCIENCE↗

Efficient perturbation-tracking method for directly probing the spectral phonon properties from molecular dynamics simulations

Existing methods for directly extracting the spectral phonon properties from molecular dynamics (MD) simulations, like the normal mode analysis (NMA) and spectral energy density analysis, all require a very long simulation time to produce reliable results with good convergence. So far, these methods are mainly applied in studies using small systems and with empirical potentials, as the heavy computational load has greatly hindered their further applications. Here we propose a perturbation-tracking (PT) method for directly probing the mode-wise phonon anharmonic frequencies and lifetimes. We show that results obtained from our method are in excellent agreement with those from the conventional NMA approach, using Si as the model material system. Comparing with the NMA approach, the PT method offers a greater accuracy and significant improvement of efficiency. It takes an average of two orders of magnitude and up to three orders of magnitude less simulation time to obtain the same lifetime result of a phonon mode with intermediate to high accuracy. Meanwhile, our method preserves all the dynamics of probed phonon mode from a particular state, which means it is capable of studying the transient thermal transport processes in a nonequilibrium system. Besides the exceptional efficiency, our method also comes with freedom to choose to probe only those modes of interest. This makes it ideal for use with large systems and in computationally demanding applications, such as ab initio MD simulations. Moreover, the PT method we propose here is very straightforward and easy to implement.

74 ATOMIC AND MOLECULAR PHYSICS↗

Light Water Reactor Sustainability Program Materials Research Pathway Technical Program Plan

The Materials Research (MR) Pathway within the Light Water Reactor Sustainability (LWRS) Program is charged with performing the research and development (R&D) to develop the scientific basis for understanding and predicting long-term environmental degradation behavior of materials in nuclear reactors. Furthermore, it is essential to use the mechanistic understanding of degradation phenomena in materials to develop mitigation, repair, and new material alternatives for existing components. The work will provide data and methods to assess performance of systems, structures, and components (SSCs) essential to safe and sustained reactor operations. The R&D products developed from the LWRS Program will be used by utilities, industry groups, and regulators to inform operational and regulatory requirements for materials in reactor SSCs subjected to long-term operation conditions, providing key input to both regulators and industry. The intent of this research is to help in reducing the operating costs, which may be in the form of offset maintenance costs due to better predictive models for component lifetimes, improved analysis of materials through nondestructive evaluation, reduced costs for repairs, or extended performance of plants through the selection of improved replacement materials. To best achieve this, industry experience and guidance are important as is their role in coordinated or collaborative research projects. The objectives of this report are to describe the motivation and organization of the MR Pathway within the LWRS Program, provide details on the individual research tasks within the MR Pathway, describe the outcomes and deliverables of the MR Pathway, including recent technical highlights and progress, and list the requirements for performing the research.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effects of HFIR neutron irradiation on fracture toughness properties of standard and Ni-doped F82H

F82H is the Japanese reference reduced-activation ferritic-martensitic (RAFM) steel for fusion blanket applications. The harsh environment of a fusion reactor, such as neutron irradiation and He/H damage, can result in significant degradation of F82H fracture toughness. Therefore, understanding the fracture toughness behavior of F82H in the fusion environment is critical to ensure the long-term safe operation of the fusion reactor. Here, we summarize seven irradiation campaigns of the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) covering five variants of F82H steels, including F82H IEA, F82H Mod3, F82H doped with 1.4% natural Ni, F82H doped with 1.4% 58 Ni, and F82H doped with 1.4% 60 Ni. The irradiation temperatures covered the range from 220 °C to 530 °C and the neutron irradiation dose spanned 4 dpa to 70 dpa. The effects of neutron irradiation temperature, dose, materials composition, Ni doping, and He production on F82H fracture toughness are discussed. Our results showed that irradiation embrittlement monotonically decreased with increasing irradiation temperature until 400 °C for F82H IEA and F82H Mod3. F82H Mod3 showed better fracture toughness than F82H IEA both before and after neutron irradiation. We determined that 1.4% Ni alloying can be applied to F82H for simulating He effect in a fission reactor without jeopardizing the fracture toughness of the material. However, more studies are needed to understand the effect of high dose (>20 dpa) and He production on F82H fracture toughness.

36 MATERIALS SCIENCE↗

Microstructure and strength of a thick-section gas-tungsten arc weld in cast Haynes® 282® alloy

A 50-mm deep gas tungsten arc weld was made with matching filler metal in cast Haynes 282 alloy. The narrow gap joint was filled with 104 weld beads. The weld deposit was of high quality with no visible indications of physical defects. The weld heat-affected zone was characterized by microcracking and localized recrystallization. Hardness testing showed that a softened region in the as-welded heat-affected zone was nearly eliminated by post-weld heat treatment. Tensile testing up to 816°C showed that cross-weld specimen strengths were about 80% of the yield strength of the original cast base metal. The rupture strengths of cross-weld specimens are within 20% of wrought base metal reference data.

36 MATERIALS SCIENCE↗

Itinerant ferromagnetism in van der Waals Fe 5 – x Ge Te 2 crystals above room temperature

Two-dimensional (2D) van der Waals (vdW) magnets have recently attracted increasing attention, as they provide a novel system for exploring 2D magnetism. However, intrinsic ferromagnetism in 2D systems has almost exclusively been observed at low temperatures, limiting their technological relevance. Fe N Ge Te 2 ( N = 3 , 4, and 5) systems are currently becoming the most attractive 2D vdW materials due to their relatively high Curie temperatures and large saturation magnetization. However, the nature of their complex yet intriguing magnetic behaviors is still unclear, in part due to the multiple inequivalent iron sites and iron vacancies. In this study, we show evolution of magnetic ordering transitions in Fe 5 – x Ge Te 2 with high Curie temperature and a strong saturation magnetization using photoemission electron microscopy and transport measurements. At 275 K, the ferromagnet transitions to a ferrimagnet, and below 110 K transitions to a state with glassy clusters. These are evidenced from temperature-dependent magnetic stripe domain evolution and anisotropic magnetoresistance measurements. Our findings show a clear magnetic ground state of Fe 5 – x Ge Te 2 at room temperature which signals that Fe 5 – x Ge Te 2 system is a very promising candidate for spintronic devices and provides a material design pathway to further increase the Curie temperature and saturation moments in vdW ferromagnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Post-Irradiation Evaluation of Eurofer97 Fracture Toughness Using Miniature Multinotch Bend Bar Specimens

In this study, we performed fracture toughness characterization of ten neutron-irradiated Eurofer97 variants using precracked miniature multi-notch bend bar (M4CVN) specimens based on the Master Curve method in the ASTM E1921 standard. The neutron irradiation was performed in the flux trap position of the High Flux Isotope Reactor (HFIR) of the Oak Ridge National Laboratory (ORNL) with the nominal irradiation temperature of 300°C and irradiation dose of 2.5 displacements per atom (dpa). Depending on the irradiation temperature and materials, we observed different degrees of irradiation hardening and embrittlement for ten Eurofer97 variants. The upper shift in the Master Curve reference temperature T0Q vs. the increase in Vickers microhardness values showed a liner relationship for only a few materials indicating different irradiation responses of the Eurofer97 variants.

Chen, Xiang↗

CHARACTERIZATION OF NI-BASED ALLOYS FOR ADVANCED ULTRA-SUPERCRITICAL POWER PLANTS

The harsh operating conditions of Advanced Ultra-Supercritical (A-USC) power plants, i.e., steam operation conditions up to 760°C (1400°F)/35 MPa (5000 psi), require the use of Ni-based alloys with high temperature performance. Currently, the U.S. Department of Energy Fossil Energy program together with Electric Power Research Institute (EPRI) and Energy Industries of Ohio (EIO) is pursuing a Component Test (ComTest) project to address material- and manufacturing-related issues for A-USC applications. Oak Ridge National Laboratory (ORNL) is supporting this project in the areas of mechanical and microstructure characterization, weld evaluation, environmental effect studies, etc. In this work, we present results from these activities on two promising Ni-based alloys and their weldments for A-USC applications, i.e., Haynes® 282® and Inconel® 740H®. Detailed results include microhardness, tensile, air and environmental creep, low cycle fatigue, creep-fatigue, environmental high cycle fatigue, and supporting microstructural characterization.

Chen, Xiang↗

Spectroscopic Evidence for Electron-Boson Coupling in Electron-Doped Sr 2 IrO 4

The pseudogap, d-wave superconductivity and electron-boson coupling are three intertwined key ingredients in the phase diagram of the cuprates. Sr 2 IrO 4 is a 5d-electron counterpart of the cuprates in which both the pseudogap and a d-wave instability have been observed. Here, we report spectroscopic evidence for the presence of the third key player in electron-doped Sr 2 IrO 4 : electron-boson coupling. A kink in nodal dispersion is observed with an energy scale of ~50 meV. The strength of the kink changes with doping, but the energy scale remains the same. Furthermore, these results provide the first noncuprate platform for exploring the relationship between the pseudogap, d-wave instability, and electron-boson coupling in doped Mott insulators.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Handbook of Advanced Manufactured Material Properties From TCR Structure Builds at ORNL (FY2019)

There is growing interest in the use of additive manufacturing techniques for the production and deployment of components for nuclear power applications. Specifically, the Transformational Challenge Reactor (TRC) program seeks to demonstrate the application of advanced manufacturing to rapidly develop and deploy a microreactor. As part of the TCR objective, a database on materials performance, such as thermophysical properties and mechanical performance, is required to help inform nuclear reactor designers, operators, and regulators regarding possible material limitations using emerging manufacturing techniques. The following report seeks to collect all available data regarding the material performance of candidate alloys and manufacturing processes pursued within the TCR program at Oak Ridge National Laboratory. At this time, this database focuses only on materials derived within the program and does not extend to additional manufacturing processes, manufacturers, or other advanced materials. Where appropriate, recommendations for applications of the data are provided and current knowledge gaps are identified.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗