Engineering Papers⌕ Search

Engineering topics

Chen, Xi

Publications and source records attributed to Chen, Xi.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Oxide layer delamination: An energy dissipation mechanism during high-velocity microparticle impacts

The break-up of microparticle surface oxides is needed to generate a clean metal-metal contact for metallurgical bonding during impact events such as seen in cold-spray. However, the mechanism by which this occurs is not clear. Here, using a laser-induced particle impact tester, we conduct site-specific experiment of single Cu microparticle impacts on a polished Cu substrate and characterize the impact sites. We observe that oxide layers on the particles begin to delaminate at velocities high enough to cause jetting of the substrate around the periphery of the impact site. We show that the energy cost of such delamination is ~30% of the energy needed to slow and stop particle as it bonds to the substrate, with the remainder being associated with the jetting process and bonding itself. At higher velocities, the oxide barrier is broken up to permit metallurgical bonding. Closer to the particle south-pole where hoop strain is low, oxide layers break up with few gaps and thus no metallurgical bonding is observed. Away from the south-pole where larger strains develop, oxide breakup permits intermittent bonding by the extrusion of bare metal into the gaps between oxide islands. These observations provide new insights towards understanding impact-induced metallurgical bonding during cold-spray process.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On-chip optical levitation with a metalens in vacuum

Optical levitation of dielectric particles in vacuum is a powerful technique for precision measurements, testing fundamental physics, and quantum information science. Conventional optical tweezers require bulky optical components for trapping and detection. Here, we design and fabricate an ultrathin dielectric metalens with a high numerical aperture of 0.88 at 1064 nm in vacuum. It consists of 500-nm-thick silicon nano-antennas, which are compatible with an ultrahigh vacuum. We demonstrate optical levitation of nanoparticles in vacuum with a single metalens. The trapping frequency can be tuned by changing the laser power and polarization. We also transfer a levitated nanoparticle between two separated optical tweezers. Optical levitation with an ultrathin metalens in vacuum provides opportunities for a wide range of applications including on-chip sensing. Such metalenses will also be useful for trapping ultracold atoms and molecules.

Shen, Kunhong↗
DOE OSTI2021

Design of tough adhesive from commodity thermoplastics through dynamic crosslinking

Tough adhesives provide resistance against high debonding forces, and these adhesives are difficult to design because of the simultaneous requirement of strength and ductility. Here, we report a design of tough reversible/recyclable adhesive materials enabled by incorporating dynamic covalent bonds of boronic ester into commodity triblock thermoplastic elastomers that reversibly bind with various fillers and substrates. The spectroscopic measurements and density functional theory calculations unveil versatile dynamic covalent binding of boronic ester with various hydroxy-terminated surfaces such as silica nanoparticles, aluminum, steel, and glass. The designed multiphase material exhibits exceptionally high adhesion strength and work of debonding with a rebonding capability, as well as outstanding mechanical, thermal, and chemical resistance properties. Bonding and debonding at the interfaces dictate hybrid material properties, and this revelation of tailored dynamic interactions with multiple interfaces will open up a new design of adhesives and hybrid materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Uncommon Behavior of Li Doping Suppresses Oxygen Redox in P2-Type Manganese-Rich Sodium Cathodes

Utilizing both cationic and anionic oxygen redox reactions is regarded as an important approach to exploit high-capacity layered cathode materials with earth abundant elements. It has been popular strategies to effectively elevate the oxygen redox activities by Li-doping to introduce unhybridized O 2p orbitals in Na x MnO 2 -based chemistries or enabling high covalency transition metals in P2-Na 0.66 Mn x TM 1-x O 2 (TM = Fe, Cu, Ni) materials. Here, we investigated the effect of Li doping on regulating the oxygen redox activities P2-structured Na 0.66 Ni 0.25 Mn 0.75 O 2 materials. Systematic X-ray characterizations and ab initio simulations have shown that the doped Li has uncommon behavior in modulating the density of states of the neighboring Ni, Mn and O, leading to the suppression of the existing oxygen and Mn redox reactivities and the promotion of the Ni redox. Furthermore, the findings provide a complementary scenario to current oxygen redox mechanisms and shed lights on developing new routes for high-performance cathodes.

25 ENERGY STORAGE↗
DOE OSTI2021

AI-based language models powering drug discovery and development

The discovery and development of new medicines is expensive, time-consuming, and often inefficient, with many failures along the way. Powered by artificial intelligence (AI), language models (LMs) have changed the landscape of natural language processing (NLP), offering possibilities to transform treatment development more effectively. Here, we summarize advances in AI-powered LMs and their potential to aid drug discovery and development. We highlight opportunities for AI-powered LMs in target identification, clinical design, regulatory decision-making, and pharmacovigilance. We specifically emphasize the potential role of AI-powered LMs for developing new treatments for Coronavirus 2019 (COVID-19) strategies, including drug repurposing, which can be extrapolated to other infectious diseases that have the potential to cause pandemics. Finally, we set out the remaining challenges and propose possible solutions for improvement.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Iron, magnesium, and titanium isotopic fractionations between garnet, ilmenite, f ayalite, biotite, and tourmaline: Results from NRIXS, ab initio , and study of mineral separates from the Moosilauke metapelite

Interpreting isotopic signatures documented in natural rocks requires knowledge of equilibrium isotopic fractionation factors. Here, we determine equilibrium Fe isotope fractionation factors between several common rock-forming minerals using a comparative approach involving three independent methods: (i) isotopic analyses of natural minerals from a metapelite from Mt. Moosilauke, New Hampshire, for which equilibration temperature and pressure are well constrained to be near the aluminosilicate triple point (T ≃ 500 °C, P ≃ 4 kbar), (ii) Nuclear Resonant Inelastic X-ray Scattering (NRIXS) measurements of Fe force constants of minerals, and (iii) Density Functional Theory (DFT) ab initio calculations of Fe force constants of minerals. The minerals studied for Fe isotopes include, in increasing order of their β-factors: garnet < ilmenite ≈ fayalite < biotite < tourmaline < muscovite ≈ plagioclase. Some of this ordering is affected by the presence of Fe 3+ in the minerals, which tends to form stiffer bonds and be associated with heavy Fe isotope enrichments relative to Fe 2+ . We are, however, able to assess the magnitude of the effect of the ratio Fe 3+ /ΣFe on equilibrium fractionation factors, notably on the ilmenite-hematite solid solution. Equilibrium Fe isotopic fractionation factors between garnet, ilmenite, biotite, tourmaline and fayalite are determined. We also report Mg and Ti isotopic compositions of selected Moosilauke minerals that allow us to better constrain the equilibrium fractionation factors for garnet-biotite-tourmaline (Mg isotopes) and biotite-ilmenite (Ti isotopes). We show how the newly determined equilibrium fractionation factors can be used to address diverse problems in Earth and planetary sciences, notably (i) Fe and Mg isotopic fractionation during anatexis, (ii) Fe isotopic fractionation in lunar ilmenite, and (iii) Ti isotopic fractionation during fluvial transport of minerals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effects of Plasticizer Content and Ceramic Addition on Electrochemical Properties of Cross-Linked Polymer Electrolyte

The development of a safe electrolyte is the key to improving energy density for next generation lithium batteries. In this work, UV-crosslinked poly(ethylene oxide) (PEO) -based polymer and composite electrolytes are systematically investigated on their ionic conductivity, mechanical and electrochemical properties. The polymer electrolytes are plasticized with non-flammable linear short-chain PEO. In the composite electrolytes, a doped lithium aluminum titanium phosphate (LATP) ceramic, LICGC™, is used as the ceramic filler. It is found that the addition of the plasticizer leads to a tradeoff between ion transport and mechanical properties. In contrast, the addition of ceramic fillers improves both the ionic conductivity and mechanical properties. The sample with 20 wt% of LICGC™ shows a conductivity of ~0.6 mS cm –1 at 50 °C. This sample also demonstrates much longer cycle life than the neat polymer electrolyte in Li platting/stripping test with a capacity of 1 mAh cm –2 . Further, a full cell made with this composite electrolyte against Li metal anode and high voltage LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode shows 94% capacity retention after 30 cycles, compared to 58% capacity retention with the neat polymer electrolyte. These results demonstrate that a hybrid of polymer/ceramic/non-flammable plasticizer is a promising path to high energy density, high voltage lithium batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Probing subwavelength in-plane anisotropy with antenna-assisted infrared nano-spectroscopy

Infrared nano-spectroscopy based on scattering-type scanning near-field optical microscopy (s-SNOM) is commonly employed to probe the vibrational fingerprints of materials at the nanometer length scale. However, due to the elongated and axisymmetric tip shank, s-SNOM is less sensitive to the in-plane sample anisotropy in general. In this article, we report an easy-to-implement method to probe the in-plane dielectric responses of materials with the assistance of a metallic disk micro-antenna. As a proof-of-concept demonstration, we investigate here the in-plane phonon responses of two prototypical samples, i.e. in (100) sapphire and x-cut lithium niobate (LiNbO 3 ). In particular, the sapphire in-plane vibrations between 350 cm–1 to 800 cm–1 that correspond to LO phonon modes along the crystal b- and c-axis are determined with a spatial resolution of < λ/10, without needing any fitting parameters. In LiNbO 3 , we identify the in-plane orientation of its optical axis via the phonon modes, demonstrating that our method can be applied without prior knowledge of the crystal orientation. Furthermore, our method can be elegantly adapted to retrieve the in-plane anisotropic response of a broad range of materials, i.e. subwavelength microcrystals, van-der-Waals materials, or topological insulators.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Oxygen Evolution on Iron Oxide Nanoparticles: The Impact of Crystallinity and Size on the Overpotential

The oxygen evolution reaction (OER) is a critical reaction in electrolysis and photoelectrolysis of water to generate and store clean energy. Therefore, the development of low-cost and efficient electrocatalysts for the OER is of great scientific and technological importance. Although promising iron oxide-based electrocatalysts have been recently developed for the OER, an in-depth experimental and theoretical analysis of the OER mechanism on iron oxide-based electrocatalysts is still needed to provide guidelines to optimize the performance of iron oxide-based electrocatalysts further. To address this need, we synthesized a series of monodisperse iron oxide nanoparticles to analyze their intrinsic OER activities. Using nanoparticles of the same size but different crystallinity, we show that amorphous iron oxide nanoparticles have better OER activity than crystalline ones. The size effect studies further revealed that the edge/defect sites are the active sites for the OER. Density functional theory calculations demonstrated that the edge/defect sites provide bridge sites to adsorb OER intermediates, resulting in low OER overpotential. These calculations confirm that the high OER activity of amorphous nanoparticles results from a high concentration of defect sites on their surface. These results provide novel strategies to increase the performance of iron oxide-based and likely other oxide-based OER electrocatalysts.

Electrochemistry↗
DOE OSTI2021

Gel composite electrolyte – an effective way to utilize ceramic fillers in lithium batteries

Achieving synergy between ion-conducting polymers and ceramics in a composite electrolyte has been proven to be difficult as the complicated ceramic/polymer interface presents challenges to understand and control. In this work, we report a strategy to utilize discrete ceramic fillers to form a gel composite electrolyte with enhanced transport properties for lithium metal batteries. The matrix of the composite membrane is crosslinked poly(ethylene oxide) with bis(trifluoromethane)sulfonimide lithium salt (LiTFSI). The membrane is plasticized with tetraethylene glycol dimethyl ether (TEGDME). The incorporation of doped-lithium aluminum titanium phosphate particles (LICGC™) into the membrane greatly improves the membrane's cycling characteristics against the lithium electrode, exhibiting lower interfacial impedance, lower overpotential and higher rate capability. The underpinnings of the superior performance of the gel composite electrolyte are discussed in depth. LICGC™ can immobilize the TFSI - anions in the polymer matrix and simultaneously promote Li+ transport by increasing the plasticizer to Li + ratio. Further, the transport enhancement is achieved without sacrificing mechanical properties. The composite membrane shows significantly improved handleability and processability. This work sheds light on the design strategy for a safe electrolyte towards stable Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Antifouling strategies for protecting bioelectronic devices

Bioelectronic devices are playing an increasingly important role in many areas of our lives. They power a significant portion of medical diagnostics and are becoming more and more important for delivery of therapeutics and monitoring of chronic symptoms. However, surface fouling phenomena, and especially biofouling in complex biological fluids, restricts the performance of these devices and severely reduces their useful lifespan. In this Research Update, we discuss the main principles and strategies that researchers use to prevent fouling and minimize or remove the foulants from bioelectronic device surfaces. We also survey a variety of antifouling approaches that can enhance device performance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Elucidating Interfacial Stability between Lithium Metal Anode and Li Phosphorus Oxynitride via In Situ Electron Microscopy

Li phosphorus oxynitride (LiPON) is one of a very few solid electrolytes that have demonstrated high stability against Li metal and extended cyclability with high Coulombic efficiency for all solid-state batteries (ASSBs). However, theoretical calculations show that LiPON reacts with Li metal. Here, we utilize in situ electron microscopy to observe the dynamic evolutions at the LiPON–Li interface upon contacting and under biasing. We reveal that a thin interface layer (~60 nm) develops at the LiPON–Li interface upon contact. This layer is composed of conductive binary compounds that show a unique spatial distribution that warrants an electrochemical stability of the interface, serving as an effective passivation layer. Our results explicate the excellent cyclability of LiPON and reconcile the existing debates regarding the stability of the LiPON–Li interface, demonstrating that, though glassy solid electrolytes may not have a perfect initial electrochemical window with Li metal, they may excel in future applications for ASSBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Regional Tau Effects on Prospective Cognitive Change in Cognitively Normal Older Adults

Studies suggest that tau deposition starts in the anterolateral entorhinal cortex (EC) with normal aging, and that the presence of β-amyloid (Aβ) facilitates its spread to neocortex, which may reflect the beginning of Alzheimer's disease (AD). Functional connectivity between the anterolateral EC and the anterior-temporal (AT) memory network appears to drive higher tau deposition in AT than in the posterior-medial (PM) memory network. Here, we investigated whether this differential vulnerability to tau deposition may predict different cognitive consequences of EC, AT, and PM tau. Using 18 F-flortaucipir (FTP) and 11 C-Pittsburgh compound-B (PiB) positron emission tomography (PET) imaging, we measured tau and Aβ in 124 cognitively normal human older adults (74 females, 50 males) followed for an average of 2.8 years for prospective cognition. We found that higher FTP in all three regions was individually related to faster memory decline, and that the effects of AT and PM FTP, but not EC, were driven by Aβ+ individuals. Moreover, when we included all three FTP measures competitively in the same model, only AT FTP significantly predicted memory decline. Our data support a model whereby tau, facilitated by Aβ, transits from EC to cortical regions that are most closely associated with the anterolateral EC, which specifically affects memory in the initial stage of AD. Memory also appears to be affected by EC tau in the absence of Aβ, which may be less clinically consequential. These findings may provide clarification of differences between normal aging and AD, and elucidate the transition between the two stages. SIGNIFICANCE STATEMENT Tau and β-amyloid (Aβ) are hallmarks of Alzheimer's disease (AD) but are also found in cognitively normal people. It is unclear whether, and how, this early deposition of tau and Aβ may affect cognition in normal aging and the asymptomatic stage of AD. We show that tau deposition in the entorhinal cortex (EC), which is common in advanced age, predicts memory decline in older adults independent of Aβ, likely reflecting normal, age-related memory loss. In contrast, tau in anterior-temporal (AT) regions is most predictive of memory decline in Aβ+ individuals. These data support the idea that tau preferentially spreads to specific cortical regions, likely through functional connections, which plays a primary role in memory decline in the early stage of AD.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Dimer rattling mode induced low thermal conductivity in an excellent acoustic conductor

A solid with larger sound speeds usually exhibits higher lattice thermal conductivity. Here, we report an exception that CuP2 has a quite large mean sound speed of 4155 m s –1 , comparable to GaAs, but single crystals show very low lattice thermal conductivity of about 4 W m –1 K –1 at room temperature, one order of magnitude smaller than GaAs. To understand such a puzzling thermal transport behavior, we have thoroughly investigated the atomic structures and lattice dynamics by combining neutron scattering techniques with first-principles simulations. This compound crystallizes in a layered structure where Cu atoms forming dimers are sandwiched in between P atomic networks. In this work, we reveal that Cu atomic dimers vibrate as a rattling mode with frequency around 11 meV, which is manifested to be remarkably anharmonic and strongly scatters acoustic phonons to achieve the low lattice thermal conductivity.

36 MATERIALS SCIENCE↗