Engineering Papers⌕ Search

Engineering topics

Chen, Wei

Publications and source records attributed to Chen, Wei.

At least 145 records · Page 8

A High-Rate Lithium Manganese Oxide-Hydrogen Battery

Rechargeable hydrogen gas batteries show promises for the integration of renewable yet intermittent solar and wind electricity into the grid energy storage. Here, we describe a rechargeable, high-rate, and long-life hydrogen gas battery that exploits a nanostructured lithium manganese oxide cathode and a hydrogen gas anode in an aqueous electrolyte. The proposed lithium manganese oxide-hydrogen battery shows a discharge potential of ~1.3 V, a remarkable rate of 50 C with Coulombic efficiency of ~99.8%, and a robust cycle life. A systematic electrochemical study demonstrates the significance of the electrocatalytic hydrogen gas anode and reveals the charge storage mechanism of the lithium manganese oxide-hydrogen battery. This work provides opportunities for the development of new rechargeable hydrogen batteries for the future grid-scale energy storage.

25 ENERGY STORAGE↗

Method and system for treatment of a gas stream that contains carbon dioxide

A method for separating carbon dioxide (CO2) from a gas stream is disclosed, in which the gas stream is reacted with a lean aminosilicone solvent in an absorber, resulting in a rich aminosilicone solvent that is then treated in a desorber to release the CO2 and regenerate lean aminosilicone solvent in a desorption reaction. The regenerated solvent is directed into a steam-producing, indirect heat exchanger that is configured to supply steam to the desorber at a temperature high enough to augment the desorption reaction. Also, selected amounts of make-up water are added to the rich aminosilicone solvent at one or more process locations between the absorber and the desorber, to lower the viscosity of the solvent and to lower the temperature required for the desorption reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a High-Rate Front-End ASIC for X-Ray Spectroscopy and Diffraction Applications

We developed a new front-end application-specific integrated circuit (ASIC) to upgrade the Maia X-ray microprobe. The ASIC instruments 32 configurable channels that perform either positive or negative charge amplification, pulse shaping, peak amplitude, and time extraction along with buffered analog storage. At a gain of 3.6 V/fC, 1-μs peaking time, and a temperature of 248 K, an electronic resolution of 13 and 10 e- rms was measured with and without a silicon drift detector (SDD) sensor, respectively. A spectral resolution of 170-eV full-width at half-maximum (FWHM) at 5.9 keV was obtained with an 55Fe source. The channel linearity was better than ± 1% with rate capabilities up to 40 kcps. The ASIC was fabricated in a commercial 250-nm process with a footprint of 6.3 mm × 3.9 mm and dissipates 167 mW of static power.

Vernon, Emerson↗

Machine learning for collective variable discovery and enhanced sampling in biomolecular simulation

Classical molecular dynamics simulates the time evolution of molecular systems through the phase space spanned by the positions and velocities of the constituent atoms. Molecular-level thermodynamic, kinetic, and structural data extracted from the resulting trajectories provide valuable information for the understanding, engineering, and design of biological and molecular materials. The cost of simulating many-body atomic systems makes simulations of large molecules prohibitively expensive, and the high-dimensionality of the resulting trajectories presents a challenge for analysis. Driven by advances in algorithms, hardware, and data availability, there has been a flare of interest in recent years in the applications of machine learning – especially deep learning – to molecular simulation. Furthermore, these techniques have demonstrated great power and flexibility in both extracting mechanistic understanding of the important nonlinear collective variables governing the dynamics of a molecular system, and in furnishing good low-dimensional system representations with which to perform enhanced sampling or develop long-timescale dynamical models. It is the purpose of this article to introduce the key machine learning approaches, describe how they are married with statistical mechanical theory into domain-specific tools, and detail applications of these approaches in understanding and accelerating biomolecular simulation.

74 ATOMIC AND MOLECULAR PHYSICS↗

Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization

Selective Laser Melted Ti-6Al-4V (as-SLMed) exhibits decreased yield strength, increased work hardening, and increased ductility after heat treatment at 730 degrees C (HT-730) or 900 degrees C (HT-900) for 2 h. To understand the change of mechanical properties, in situ high energy X-ray diffraction (HEXRD) is used to examine the phase composition, load partitioning, slip system activity, and dislocation density evolution in all three specimens. The as-SLMed specimen is dominated by martensitic α'. After heat treatment, α' partly or fully decomposes into α+β, reducing the yield strength. In HT-730, beta precipitates with confined size show much higher lattice strain than the α'/α matrix during deformation; in HT-900, the lattice strain difference is mostly eliminated. This is a key reason for the increased ductility in HT-900. From the anisotropic lattice strain development, basal slip is identified as the easiest slip system in α'/α. Using an elasto-plastic self-consistent (EPSC) model, the critical resolved shear stress ratio between prismatic slip and basal slip (CRSS prism /CRSS basal ) is estimated to be 1.31 and 1.16 in the as -SLMed and the HT-900 specimens, respectively. Further, the alpha phase in HT-900 is able to activate multiple slip systems and accumulate more dislocations during plastic deformation. This explains why HT-900 has better ductility and higher work hardening rate than the other two specimens.

36 MATERIALS SCIENCE↗

Solubility-Dependent Protective Effects of Binary Alloys for Lithium Anode

Recently, alloys have been widely utilized as protection layers for homogenized Li growth. However, the protective mechanisms for different alloys are not clearly understood. In this work, guided by the binary phase diagrams, Mg, Au, Zn, Al, Fe, and Cu protective layers have been selected for study of their protective abilities and mechanisms. The selected metals can be classified into three categories according to the nature of their associated alloy protective layers: (1) metals with high solubility in Li while not forming any intermediate line compounds, e.g., Mg, which is good for fast Li stripping; (2) metals with limited solid solubility but forming stable line compounds with Li upon the lithiation, e.g., Au, Zn, and Al, where the formed stable line compounds Li x Au, Li x Zn, and Li x Al will hamper Li kinetics; (3) metals with negligible mutual solubility and no line compound formation with Li, e.g., Fe and Cu, which block the Li stripping path and therefore result in the highest polarization voltage.

25 ENERGY STORAGE↗

Membrane-Free Zn/MnO 2 Flow Battery for Large-Scale Energy Storage

The traditional Zn/MnO 2 battery has attracted great interest due to its low cost, high safety, high output voltage, and environmental friendliness. However, it remains a big challenge to achieve long-term stability, mainly owing to the poor reversibility of the cathode reaction. Different from previous studies where the cathode redox reaction of MnO 2 /MnOOH is in solid state with limited reversibility, in this work a new aqueous rechargeable Zn/MnO 2 flow battery is constructed with dissolution–precipitation reactions in both cathodes (Mn 2+ /MnO 2 ) and anodes (Zn 2+ /Zn), which allow mixing of anolyte and catholyte into only one electrolyte and remove the requirement for an ion selective membrane for cost reduction. Impressively, this new battery exhibits a high discharge voltage of ≈1.78 V, good rate capability (10C discharge), and excellent cycling stability (1000 cycles without decay) at the areal capacity ranging from 0.5 to 2 mAh cm -2 . More importantly, this battery can be readily enlarged to a bench scale flow cell of 1.2 Ah with good capacity retention of 89.7% at the 500th cycle, displaying great potential for large-scale energy storage.

25 ENERGY STORAGE↗

An in situ shearing x-ray measurement system for exploring structures and dynamics at the solid–liquid interface

Revealing interfacial structure and dynamics has been one of the essential thematic topics in material science and condensed matter physics. Synchrotron-based x-ray scattering techniques can deliver unique and insightful probing of interfacial structures and dynamics, in particular, in reflection geometries with higher surface and interfacial sensitivity than transmission geometries. We demonstrate the design and implementation of an in situ shearing x-ray measurement system, equipped with both inline parallel-plate and cone-and-plate shearing setups and operated at the advanced photon source at Argonne National Laboratory, to investigate the structures and dynamics of end-tethered polymers at the solid-liquid interface. With a precise lifting motor, a micrometer-scale gap can be produced by aligning two surfaces of a rotating upper shaft and a lower sample substrate. A torsional shear flow forms in the gap and applies tangential shear forces on the sample surface. The technical combination with nanoscale rheology and the utilization of in situ x-ray scattering allow us to gain fundamental insights into the complex dynamics in soft interfaces under shearing. In this work, we demonstrate the technical scope and experimental capability of the in situ shearing x-ray system through the measurements of charged polymers at both flat and curved interfaces upon shearing. Furthermore, through the in situ shearing x-ray scattering experiments integrated with theoretical simulations, we aim to develop a detailed understanding of the short-range molecular structure and mesoscale ionic aggregate morphology, as well as ion transport and dynamics in soft interfaces, thereby providing fundamental insight into a long-standing challenge in ionic polymer brushes with a significant technological impact.

36 MATERIALS SCIENCE↗

Structure and dynamics of lipid membranes interacting with antivirulence end-phosphorylated polyethylene glycol block copolymers

The structure and dynamics of lipid membranes in the presence of extracellular macromolecules are critical for cell membrane functions and many pharmaceutical applications. The pathogen virulence-suppressing end-phosphorylated polyethylene glycol (PEG) triblock copolymer (Pi-ABAPEG) markedly changes the interactions with lipid vesicle membranes and prevents PEG-induced vesicle phase separation in contrast to the unphosphorylated copolymer (ABAPEG). Pi-ABAPEG weakly absorbs on the surface of lipid vesicle membranes and slightly changes the structure of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC) unilamellar vesicles at 37 °C, as evidenced by small angle neutron scattering. X-ray reflectivity measurements confirm the weak adsorption of Pi-ABAPEG on DMPC monolayer, resulting in a more compact DMPC monolayer structure. Neutron spin-echo results show that the adsorption of Pi-ABAPEG on DMPC vesicle membranes increases the membrane bending modulus $κ$.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Re-Engineering Poly(Acrylic Acid) Binder toward Optimized Electrochemical Performance for Silicon Lithium-Ion Batteries: Branching Architecture Leads to Balanced Properties of Polymeric Binders

Silicon is a promising anode material for lithium-ion batteries with its superior capacity. However, the drastic volume changes during lithiation/delithiation cycles hinder the cycling performance, resulting in particle pulverization, conductivity loss, and an unstable electrode-electrolyte interface. In this work, a series of synthetic polymeric binders, poly(acrylic acid-co-tetra(ethylene glycol) diacrylate)-featuring a poly(acrylic acid) (PAA) backbone branched via tetra(ethylene glycol) diacrylate (TEGDA)-are developed that edge toward evidencing well-balanced properties to confront capacity fading in Si-based electrodes. The incorporation of ether chain not only leads to the branching architecture of the PAA backbone, thus affecting its mechanical properties, but also promotes the conductivity of Li ions. As a result, a synergistic performance improvement is observed in both half and full cells. The best-performing cell using a branched PAA binder (bPAA) with a feeding molar ratio ([TEGDA]:[acrylic acid(AA)]) of 0.2 results in a 10% increase in initial capacity and a 31% increase in capacity retention over 100 cycles compared to the linear PAA cell. The cross-sectional microscopic images of the cycled electrodes reveal that bPAA binders can drastically reduce the electrode expansion. This improvement results from the well-balanced properties of the polymer design, which could guide further development for more advanced binder materials.

25 ENERGY STORAGE↗

Enrichment and Distribution of Pb 2+ Ions in Zwitterionic Poly(cysteine methacrylate) Brushes at the Solid–Liquid Interface

Cysteine-based polyzwitterionic brushes have been prepared via a two-step route. First, poly(allyl methacrylate) (PAMA) brushes have been grown from the surface of silicon substrates using surface-initiated atom transfer radical polymerization. The obtained PAMA brushes with free pendant vinyl groups were further modified via radical thiol-ene addition reaction to attach L-cysteine moieties. Surface zeta potential investigations on pH-responsiveness of these poly(cysteine methacrylate) (PCysMA) brushes confirm their zwitterionic character at intermediate pH range, while at pH values either below pH 3.50 or above pH 8.59, they exhibit polyelectrolyte character. Under acid (pH < 3.50) or base (pH > 8.59) conditions, they possess either cationic or anionic character, respectively. In the zwitterionic region, these PCysMA brushes show positive surface $\zeta$ potential in the presence of Pb(CH 3 COO) 2 solutions of various concentrations. The results are in line with microscopic investigations using anomalous X-ray reflectivity (AXRR) carried out along the absorption edge of Pb 2+ ions. When the photon energies were varied around the absorption L3 edge of lead (13037 eV), the Pb 2+ concentration normal to the silicon substrates, as a function of depth inside PCysMA brushes, could be revealed at the nanoscale. Both zeta potential and AXRR measurements confirm the enrichment of Pb 2+ ions inside PCysMA brushes, indicating the potential of PCysMA to be used as a water purification material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Metallic 1T Phase, 3d 1 Electronic Configuration and Charge Density Wave Order in Molecular Beam Epitaxy Grown Monolayer Vanadium Ditelluride

We present a combined experimental and theoretical study of monolayer vanadium ditelluride, VTe2, grown on highly oriented pyrolytic graphite by molecular-beam epitaxy. Using various in situ microscopic and spectroscopic techniques, including scanning tunneling microscopy/spectroscopy, synchrotron X-ray and angle-resolved photoemission, and X-ray absorption, together with theoretical analysis by density functional theory calculations, we demonstrate direct evidence of the metallic 1T phase and 3d1 electronic configuration in monolayer VTe2 that also features a (4 × 4) charge density wave order at low temperatures. In contrast to previous theoretical predictions, our element-specific characterization by X-ray magnetic circular dichroism rules out a ferromagnetic order intrinsic to the monolayer. Our findings provide essential knowledge necessary for understanding this interesting yet less explored metallic monolayer in the emerging family of van der Waals magnets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗