Engineering topics

Chen, W. C.

Publications and source records attributed to Chen, W. C..

8 records

NASA NTRS1993

Optimization of a Centrifugal Impeller Design Through CFD Analysis

This paper discusses the procedure, approach and Rocketdyne CFD results for the optimization of the NASA consortium impeller design. Two different approaches have been investigated. The first one is to use a tandem blade arrangement, the main impeller blade is split into two separate rows with the second blade row offset circumferentially with respect to the first row. The second approach is to control the high losses related to secondary flows within the impeller passage. Many key parameters have been identified and each consortium team member involved will optimize a specific parameter using 3-D CFD analysis. Rocketdyne has provided a series of CFD grids for the consortium team members. SECA will complete the tandem blade study, SRA will study the effect of the splitter blade solidity change, NASA LeRC will evaluate the effect of circumferential position of the splitter blade, VPI will work on the hub to shroud blade loading distribution, NASA Ames will examine the impeller discharge leakage flow impacts and Rocketdyne will continue to work on the meridional contour and the blade leading to trailing edge work distribution. This paper will also present Rocketdyne results from the tandem blade study and from the blade loading distribution study. It is the ultimate goal of this consortium team to integrate the available CFD analysis to design an advanced technology impeller that is suitable for use in the NASA Space Transportation Main Engine (STME) fuel turbopump.

Chen, W. C.↗

NASA NTRS1986

A generalized theory for eccentric and misalignment effects in high-pressure annular seals

High-pressure annular seal leakage and dynamic coefficients vary with eccentricity and misalignment. Recent seal leakage data with both concentric and fully eccentric alignments support the seal leakage model with surface roughness and eccentricity effects included. In this paper, the seal dynamic coefficient calculation has been generalized and allows direct calculation of the seal dynamic coefficients at any circumferential location. The generalized solution agrees with the results obtained by using the calculated values of an earlier paper and performing a coordinate transformation. The analysis results coincide with the measured data in showing that the stiffness and damping matrices of seal coefficients are not skew symmetric, and the main diagonal seal coefficients are not equal. The measured direct stiffnesses were found higher than predicted by the concentric seal theory, but this may be explained by the presence of eccentricity in the test operating mode.

Chen, W. C.↗

NASA NTRS1986

Rough/Smooth Rotary Seal

Rotary seal for turbopump combines low leakage of labyrinth seal with high load capacity of smooth-surface annular seal. New seal acts as strong journal bearing that provides high stiffness - about same as that of ball bearings for turbopump shaft. Seal shares load with ball bearings and prolongs their lives. At same time, seal allows minimal leakage of fluid from pump. By combining leakage control and bearing functions, seal makes multiple seals unnecessary and allows compact design.

Chen, W. C.↗

NASA NTRS1985

A study on inclusion formation mechanism in alpha-LiIO sub 3 crystals

The spatial distribution of inclusions in alpha-LiIO3 crystals by means of an argon laser beam scanning technique is studied. The effects of crystal dimensions and solution fluid flow on the inclusion formation in the alpha-LiIO3 crystals were observed. It was further shown that the fluid flow plays an important role in the formation of inclusions. The results obtained were further applied and verified by growing a perfect alpha-LiIO3 single crystal. An experimental foundation for further theoretical studies on the causes of inclusions may be provided.

Chen, W. C.↗

NASA NTRS1985

Eccentricity and misalignment effects on the performance of high-pressure annular seals

Annular pressure seals act as powerful hydrostatic bearings and influence the dynamic characteristics of rotating machinery. This work, using the existing concentric seal theories, provides a simple approximate method for calculation of both seal leakage and the dynamic coefficients for short seals with large eccentricity and/or misalignment of the shaft. Rotation and surface roughness effects are included for leakage and dynamic force calculation. The leakage calculations for both laminar and turbulent flow are compared with experimental results. The dynamic coefficients are compared with analytical results. Excellent agreement between the present work and published results have been observed up to the eccentricitiy ratio of 0.8.

Chen, W. C.↗

NASA NTRS1984

Antivortex Inlet Ribs for Fluid-Seals

Instability in rotating machinery reduced. Ring of ribs fastened to existing stator in turbopump pressure-seal inlet. Ribs suppress swirl in flow entering seal. Rib concept offers relatively inexpensive solution to some lateral-instability problems in many other systems with rotating pressure seals.

Chen, W. C.↗

NASA NTRS1978

A literature review on fatigue and creep interaction

Life-time prediction methods, which are based on a number of empirical and phenomenological relationships, are presented. Three aspects are reviewed: effects of testing parameters on high temperature fatigue, life-time prediction, and high temperature fatigue crack growth.

Chen, W. C.↗

NASA NTRS1976

Fatigue crack growth at elevated temperature 316 stainless steel and H-13 steel

Crack growths were measured at elevated temperatures under four types of loading: pp, pc, cp, and cc. In H-13 steel, all these four types of loading gave nearly the same crack growth rates, and the length of hold time had negligible effects. In AISI 316 stainless steel, the hold time effects on crack growth rate were negligible if the loading was tension-tension type; however, these effects were significant in reversed bending load, and the crack growth rates under these four types of loading varied considerably. Both tensile and compressive hold times caused increased crack growth rate, but the compressive hold period was more deleterious than the tensile one. Metallographic examination showed that all the crack paths under different types of loading were largely transgranular for both CTS tension-tension specimens and SEN reversed cantilever bending specimens. In addition, an electric potential technique was used to monitor crack growth at elevated temperature.

Chen, W. C.↗