Engineering topics

Chen, L.-D.

Publications and source records attributed to Chen, L.-D..

5 records

NASA NTRS1992

A numerical study of Li-SF6 wick combustion - Forced and mixed convective burning

A numerical study is conducted to study Li-SF6 wick diffusion flames under mixed convective burning conditions at a pressure of 0.01 MPa. Both planar and cylindrical wicks are considered. The model is based on a conserved scalar approach. The objective of this study is to assess the effects of particular parameters on the burning rate and heat transfer. The flat-plate solution yields a fuel mass burning rate per unit surface area following the x exp -1/2 dependence of the classical similarity solution, where x is the streamwise distance. Cylindrical wick geometries yield enhanced burning rates over planar wicks. For the case of mixed convective burning, the burning rate results approach either the forced or natural convective burning limits as ambient streamwise velocity is changed. Critical Richardson numbers specifying these burning limits are determined for a given condition. Reducing gravity results in a lower burning rate because the influence of natural convection is diminished. Under reduced gravity of 1/1000 of the sea-level value, mixed convective burning nearly resembles forced convection.

Damaso, R. C.↗

NASA NTRS1985

Flow and atomization in flashing injectors

Flashing injection involves expanding a fluid through an injector until a supersaturated state is reached, causing a portion of the fluid to flash to a vapor. This investigation considered the flow, atomization and spreading properties of flashing injectors with flowing liquids containing dissolved gases (Jet A/air) as well as superheated liquids (Freon-11). The use of a two-stage expansion process, separated by an expansion chamber, was found to be beneficial for good atomization properties of flashing injection - particularly for dissolved gas systems. Both locally homogeneous and separated flow models provided good predictions of injector flow properties. Conventional correlations for drop sizes from pressure and airblast injectors were successfully modified, using the separated flow model to prescribe injector exit conditions, and to correlate drop size measurements. Additional experimental results are provided for spray angles of sprays from flashing injectors.

Solomon, A. S. P.↗

NASA NTRS1983

Predictions of the structure of turbulent, particle-laden, round jets

Models of gas and particle motion in turbulent, particle-laden, round jets were evaluated using existing measurements of flow structure. Three models were considered: (1) a locally homogeneous flow model, where velocities and turbulent mixing properties of both phases were assumed to be equal; (2) a deterministic separated flow model, where interphase slip was considered but effects of turbulent dispersion were ignored; and (3) a stochastic separated flow model where effects of interphase slip and turbulent dispersion were considered using random sampling techniques. In all three cases, mean and turbulent properties of the continuous phase were found with a well-calibrated k-epsilon model. The locally homogeneous flow and deterministic separated flow models over- and underestimated particle spread and flow development rates, respectively. The stochastic separated flow model, however, yielded satisfactory predictions of flow structure - except at high particle loadings. Uncertainties in initial conditions for the measurements and possible effects of turbulence modulation by the particles are proposed as the reason for these errors.

Shuen, J.-S.↗

NASA NTRS1983

Evaluation of a stochastic model of particle dispersion in a turbulent round jet

A stochastic model of particle dispersion by turbulence, proposed by Gosman and Ioannides (1981), is evaluated. The method employs a k-epsilon model to estimate turbulence properties. Dispersion is determined by computing particle motion, with random sampling to obtain instantaneous flow properties for a statistically significant number of particle trajectories. The stochastic model yields good results particularly when eddy lifetimes are evaluated. The method allows the effects of large relative velocities between the particles and the flow, drag properties at Reynolds numbers greater than the Stokes flow regime, and the variations of local turbulence properties to be readily handled, at least for boundary layer flows.

Shuen, J.-S.↗

NASA NTRS1982

Atomization and combustion properties of flashing injectors

Flashing injection involves expanding a fluid through an injector until a supersaturated state is reached, causing a portion of the fluid to flash to a vapor. This investigation considered the flow, atomization and spreading properties of flashing injectors flowing liquids containing dissolved gases (Jet A/air) as well as superheated liquids (Freon 11). The use of a two stage expansion process, separated by an expansion chamber, was found to be beneficial for good atomization properties of flashing injection - particularly for dissolved gas systems. Both locally homogeneous and separated flow models provided good predictions of injector flow properties. Conventional correlations for drop sizes from pressure atomized and airblast injectors were successfully modified, using the separated flow model to prescribe injector exit conditions, to correlate drop size measurements. Additional experimental results are provided for spray angle and combustion properties of sprays from flashing injectors.

Solomon, A. S. P.↗