Engineering Papers⌕ Search

Engineering topics

Chen, Ke

Publications and source records attributed to Chen, Ke.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Earth-abundant Li-ion cathode materials with nanoengineered microstructures

Manganese-based materials have tremendous potential to become the next-generation lithium-ion cathode as they are Earth abundant, low cost and stable. Here we show how the mobility of manganese cations can be used to obtain a unique nanosized microstructure in large-particle-sized cathode materials with enhanced electrochemical properties. By combining atomic-resolution scanning transmission electron microscopy, four-dimensional scanning electron nanodiffraction and in situ X-ray diffraction, we show that when a partially delithiated, high-manganese-content, disordered rocksalt cathode is slightly heated, it forms a nanomosaic of partially ordered spinel domains of 3–7 nm in size, which impinge on each other at antiphase boundaries. The short coherence length of these domains removes the detrimental two-phase lithiation reaction present near 3 V in a regular spinel and turns it into a solid solution. This nanodomain structure enables good rate performance and delivers 200 mAh g –1 discharge capacity in a (partially) disordered material with an average primary particle size of ~5 µm. The work not only expands the synthesis strategies available for developing high-performance Earth-abundant manganese-based cathodes but also offers structural insights into the ability to nanoengineer spinel-like phases.

36 MATERIALS SCIENCE↗
DOE OSTI2024

MgB$_{2}$ Coating by HPCVD for 1.3-GHz Superconducting RF Cavities

While MgB 2 possesses promising material parameters for SRF cavities with higher Q, higher gradient, and higher operation temperatures than Nb cavities, such cavity properties have not been demonstrated using MgB 2 . As part of a continuing effort to fabricate MgB 2 -coated SRF cavities by hybrid physical chemical vapor deposition (HPCVD), we present here an HPCVD system design for coating the inside wall of 1.3-GHz copper cavities with MgB 2 . The cavity is heated using a pair of clamshell resistive heaters that directly contact the cavity body. Here, the new heater design is more compact and requires less power to reach the deposition temperature (~500°C for MgB 2 deposition on copper.) Preliminary test of MgB 2 films grown on small copper substrates, mounted at different locations on the cavity, shows T c of 28.4 ~ 34.3 K, measured by AC susceptibility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Holistic energy landscape management in 2D/3D heterojunction via molecular engineering for efficient perovskite solar cells

Constructing two-dimensional (2D) perovskite atop of 3D with energy landscape management is still a challenge in perovskite photovoltaics. Here, we report a strategy through designing a series of π-conjugated organic cations to construct stable 2D perovskites and to realize delicate energy level tunability at 2D/3D heterojunctions. As a result, the hole transfer energy barriers can be reduced both at heterojunctions and within 2D structures, and the preferable work function shift reduces charge accumulation at interface. Leveraging these insights and also benefitted from the superior interface contact between conjugated cations and poly(triarylamine) (PTAA) hole transporting layer, a solar cell with power conversion efficiency of 24.6% has been achieved, which is the highest among PTAA-based n-i-p devices to the best of our knowledge. The devices exhibit greatly enhanced stability and reproducibility. This approach is generic to several hole transporting materials, offering opportunities to realize high efficiency without using the unstable Spiro-OMeTAD.

14 SOLAR ENERGY↗
DOE OSTI2023

Tailoring Molecular-Scale Contact at Perovskite/Polymeric Hole Transporting Material Interface for Efficient Solar Cells

Perovskite solar cells (PSCs) have delivered more than 25% of power conversion efficiency (PCE) and incorporating polymers as hole transporting layers (HTLs) can further enhance the stability of devices towards the goal of commercialization. Among various polymeric hole transporting materials, poly(triaryl amine) (PTAA) is one of the promising HTL candidates with good stability; however, the hydrophobicity of PTAA causes problematic interfacial contact with perovskite, limiting the device performance. Using molecular side-chain engineering, we successfully constructed a uniform two-dimensional (2D) perovskite interlayer with conjugated ligands, between three-dimensional (3D) perovskites and PTAA. Further, employing conjugated ligands as cohesive elements, perovskite/PTAA interfacial adhesion was significantly improved. As a result, the thin and lateral extended 2D/3D heterostructure enabled the as-fabricated PTAA-based PSCs to achieve a PCE of 23.7%, improved from the 18% of reference devices. Owing to the increased ion migration energy barrier and conformal 2D coating, unencapsulated devices with the new ligands exhibited both superior thermal stability under 60°C heating and moisture stability in ambient conditions.

14 SOLAR ENERGY↗
DOE OSTI2023

Ultrathin epitaxial MgB 2 on SiC: Substrate surface-polarity-dependent properties

High-quality, ultrathin superconducting films are required for advanced devices such as hot-electron bolometers, superconducting nanowire single-photon detectors, and quantum applications. Using hybrid physical-chemical vapor deposition, we show that MgB 2 films as thin as 4 nm can be fabricated on the carbon-terminated 6⁢H-SiC (0001) surface with a superconducting transition temperature above 33 K and a rms roughness of 0.7 nm. Remarkably, the film quality is a function of the SiC surface termination, with the C-terminated surface preferred to the Si-terminated surface. To understand the MgB 2 thin film/SiC substrate interactions giving rise to this difference, we characterized the interfacial structures using Rutherford backscattering spectroscopy/channeling, electron-energy-loss spectroscopy, and x-ray photoemission spectroscopy. The MgB 2 /SiC interface structure is complex and different for the two terminations. Both terminations incorporate substantial unintentional oxide layers influencing MgB 2 growth and morphology, but with a different extent, intermixing, and interface chemistry. In this paper, we report measurements of transport, resistivity, and the critical superconducting temperature of MgB 2 /SiC that are different for the two terminations, and they link interfacial structure variations to observed differences. The result shows that the C face of SiC is a preferred substrate for the deposition of ultrathin superconducting MgB 2 films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mitigating Interfacial Mismatch between Lithium Metal and Garnet-Type Solid Electrolyte by Depositing Metal Nitride Lithiophilic Interlayer

Solid-state lithium batteries are generally considered as the next-generation battery technology that benefits from inherent nonflammable solid electrolytes and safe harnessing of high-capacity lithium metal. Among various solid-electrolyte candidates, cubic garnet-type Li 7 La 3 Zr 2 O 12 ceramics hold superiority due to their high ionic conductivity (10 –3 to 10 –4 S cm -1 ) and good chemical stability against lithium metal. However, practical deployment of solid-state batteries based on such garnet-type materials has been constrained by poor interfacing between lithium and garnet that displays high impedance and uneven current distribution. Herein, we propose a facile and effective strategy to significantly reduce this interfacial mismatch by modifying the surface of such garnet-type solid electrolyte with a thin layer of silicon nitride (Si 3 N 4 ). This interfacial layer ensures an intimate contact with lithium due to its lithiophilic nature and formation of an intermediate lithium–metal alloy. The interfacial resistance experiences an exponential drop from 1197 to 84.5 Ω cm 2 . Lithium symmetrical cells with Si 3 N 4 -modified garnet exhibited low overpotential and long-term stable plating/stripping cycles at room temperature compared to bare garnet. Furthermore, a hybrid solid-state battery with Si 3 N 4 -modified garnet sandwiched between lithium metal anode and LiFePO 4 cathode was demonstrated to operate with high cycling efficiency, excellent rate capability, and good electrochemical stability. This work represents a significant advancement toward use of garnet solid electrolytes in lithium metal batteries for the next-generation energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2021

Multifunctional Conjugated Ligand Engineering for Stable and Efficient Perovskite Solar Cells

Surface passivation is an effective way to boost the efficiency and stability of perovskite solar cells (PSCs). However, a key challenge faced by most of the passivation strategies is reducing the interface charge recombination without imposing energy barriers to charge extraction. Here, a novel multifunctional semiconducting organic ammonium cationic interface modifier inserted between the light-harvesting perovskite film and the hole-transporting layer is reported. It is shown that the conjugated cations can directly extract holes from perovskite efficiently, and simultaneously reduce interface non-radiative recombination. Together with improved energy level alignment and the stabilized interface in the device, a triple-cation mixed-halide medium-bandgap PSC with an excellent power conversion efficiency of 22.06% (improved from 19.94%) and suppressed ion migration and halide phase segregation, which lead to a long-term operational stability, is demonstrated. Finally, this strategy provides a new practical method of interface engineering in PSCs toward improved efficiency and stability.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Advanced strategies for the development of porous carbon as a Li host/current collector for lithium metal batteries

Lithium metal is considered a promising anode material for high-energy-density rechargeable batteries because of its high specific theoretical capacity (3860 mAh g -1 , low mass density (0.534 g cm -3 ), and low electrochemical redox potential (-3.04 V vs. the standard hydrogen electrode). However, the high reactivity of Li with the electrolyte leads to the formation of an unstable solid electrolyte interphase (SEI) and continuous side reactions. Also, the non-uniform lithium-ion flux and infinite volume expansion of Li metal cause the growth of Li dendrites. These pose significant safety challenges and cause rapid capacity fading of the lithium metal batteries (LiMBs). To resolve these issues, a low-cost, easily processed, lightweight, high-performance carbon-based porous matrix is considered promising to host Li metal deposition. The three-dimensional (3D) porous nano/microstructured carbon provides sufficient space for Li accommodation during Li plating, buffers the volume changes during Li plating/stripping, and lowers the effective current density contributing to dendrite-free Li deposition. Besides, the outstanding electrochemical and mechanical stability, flexibility and the high electronic conductivity enable the nano/microstructured carbon to serve as both Li host and current collector. The development of 3D carbon/Li composite by mechanical roll-press techniques not only eliminates the complex and risky procedure of making carbon/Li composite based on Li plating or molten Li infusion but also stabilizes the capacity at higher Li plating/stripping rates. Recently, there is an advancement in the lithiophilic decorations of 3D structure to introduce sufficient nucleation sites and the development of artificial SEI on top of the 3D matrix to suppress Li dendrite formation. Such 3D structural modifications create a uniform electric field, lower the Li nucleation overpotential, provide strong mechanical and chemical stability, and stabilize the interface thereby inhibiting the degradation of lithium and the electrolyte. Here we summarize the research progress on porous carbon/Li composites in terms of materials type, structure, fabrication technique, their electrochemical battery performance, and identify the critical challenges that need to be addressed for high-energy-density practical LiMBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Tailored PEDOT:PSS hole transport layer for higher performance in perovskite solar cells: Enhancement of electrical and optical properties with improved morphology

Precise control over the charge carrier dynamics throughout the device can result in outstanding performance of perovskite solar cells (PSCs). Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) is the most actively studied hole transport material in p-i-n structured PSCs. However, charge transport in the PEDOT:PSS is limited and inefficient because of its low conductivity with the presence of the weak ionic conductor PSS. In addition, morphology of the underlying PEDOT:PSS layer in PSCs plays a crucial role in determining the optoelectronic quality of the active perovskite absorber layer. This work is focused on realization of a non-wetting conductive surface of hole transport layer suitable for the growth of larger perovskite crystalline domains. This is accomplished by employing a facile solvent-engineered (ethylene glycol and methanol) approach resulting in removal of the predominant PSS in PEDOT:PSS. The consequence of acquiring larger perovskite crystalline domains was observed in the charge carrier dynamics studies, with the achievement of higher charge carrier lifetime, lower charge transport time and lower transfer impedance in the solvent-engineered PEDOT:PSS-based PSCs. Use of this solvent-engineered treatment for the fabrication of MAPbI3 PSCs greatly increased the device stability witnessing a power conversion efficiency of 18.18%, which corresponds to ~37% improvement compared to the untreated PEDOT:PSS based devices.

14 SOLAR ENERGY↗
DOE OSTI2020

Optical properties of cubic boron arsenide

The ultrahigh thermal conductivity of cubic boron arsenide (BAs) makes it a promising material for next-generation electronics and optoelectronics. Here, we report measured optical properties of BAs crystals, including the complex dielectric function, refractive index, and absorption coefficient in the ultraviolet, visible, and near-infrared wavelength range. In this work, the data were collected at room temperature using spectroscopic ellipsometry and transmission and reflection spectroscopy. We further calculated the optical response using density functional theory and many-body perturbation theory, considering quasiparticle and excitonic corrections. The computed values for the direct and indirect bandgaps (4.25 eV and 2.07 eV) agree well with the measured results (4.12 eV and 2.02 eV). Our findings pave the way for using BAs in future electronic and optoelectronic applications that take advantage of its demonstrated ultrahigh thermal conductivity and predicted high ambipolar carrier mobility.

74 ATOMIC AND MOLECULAR PHYSICS↗