Engineering Papers⌕ Search

Engineering topics

Chen, Fanglin

Publications and source records attributed to Chen, Fanglin.

At least 91 records · Page 5

Synthesis and characterization of Mo-doped SrFeO 3-δ as cathode materials for solid oxide fuel cells

This paper demonstrates the potential application of Mo-doped SrFeO 3-δ perovskites as new cathode materials for solid oxide fuel cells (SOFCs). SrFe 1-x MoxO 3-δ (x = 0, 0.05, 0.1, 0.2 and 0.25) perovskite materials have been synthesized by a microwave-assisted combustion method. By doping with Mo, the electrical conductivity of the doped SrFeO 3-δ in air is reduced with increasing amounts of Mo. At 800 °C, the conductivity drops from about 62 to 22 S cm -1 when the doping level is increased to 25%. According to X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and temperature programmed reduction (TPR) results, a decrease in the concentration of charge carrier Fe 4+ ions may account for the decrease in electrical conductivity. In contrast, the resistance to sintering and tolerance to reduction of SrFeO 3-δ are improved by Mo-doping. Additionally, the thermal expansion coefficient at 800 °C drops from 40.8 × 10 -6 K -1 for SrFeO 3-δ to 25.7 × 10 -6 K -1 for SrFe 0.8 Mo 0.2 O 3-δ and 20.9 × 10 -6 K -1 for SrFe0.75Mo0.25O 3-δ . This significant decrease in the thermal expansion coefficient makes Mo-doped SrFeO 3-δ materials attractive as cathode candidates for SOFCs. Finally, a relatively low polarization resistance of 0.074 Ω cm2 is obtained for SrFe 0.8 Mo 0.2 O 3-δ at 800 °C in air.

25 ENERGY STORAGE↗

Sr 2 Fe 1.5 Mo 0.5 O 6-δ as a regenerative anode for solid oxide fuel cells

Sr 2 Fe 1.5 Mo 0.5 O 6-δ (SFM) was prepared using a microwave-assisted combustion synthesis method. Rietveld refinement of powder X-ray diffraction data reveals that SFM crystallizes in the simple cubic perovskite structure with iron and molybdenum disordered on the B-site. No structure transition was observed by variable temperature powder X-ray diffraction measurements in the temperature range of 25–800 °C. XPS results show that the iron and molybdenum valences change with an increase in temperature, where the mixed oxidation states of both iron and molybdenum are believed to be responsible for the increase in the electrical conductivity with increasing temperature. SFM exhibits excellent redox stability and has been used as both anode and cathode for solid oxide fuel cells. Presence of sulfur species in the fuel or direct utilization of hydrocarbon fuel can result in loss of activity, however, as shown in this paper, the anode performance can be regenerated from sulfur poisoning or coking by treating the anode in an oxidizing atmosphere. Thus, SFM can be used as a regenerating anode for direct oxidation of sulfur-containing hydrocarbon fuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and characterizations of A-site deficient perovskite Sr0.9Ti0.8-xGaxNb0.2O3

The effects of reduction and Ga-doping on the physicochemical properties of A-site deficient perovskites Sr0.9Ti0.8-xGaxNb0.2O3 (x = 0, 0.05, 0.1, 0.15 and 0.2) are reported. With 10% Ga doping, the sample sintered in air and treated at 1400 °C in H2 atmosphere exhibits the highest electrical conductivity. It is found that the Ga-doping lowers the sinterability but promotes the reduction of Sr0.9Ti0.8-xGaxNb0.2O3. The XRD analysis on the reduced samples suggests that some cations are reduced during the treatment. However, without high temperature pre-reduction, the improvement of Ga-doping is limited and the overall cell performance using Sr0.9Ti0.8-xGaxNb0.2O3 as an anode without catalysts is still relatively low.

36 MATERIALS SCIENCE↗

Perovskite Sr2Fe1.5Mo0.5O6-δ as electrode materials for symmetrical solid oxide electrolysis cells

Perovskite Sr2Fe1.5Mo0.5O6-δ (SFM) has been successfully prepared by a microwave-assisted combustion method in air and employed as both anode and cathode in symmetrical solid oxide electrolysis cells (SOECs) for hydrogen production for the first time in this work. Influence of cell operating temperature, absolute humidity (AH) as well as applied direct current (DC) on the impedance of single cells with the configuration of SFM|La0.9Sr0.1Ga0.8Mg0.2O3 (LSGM)|SFM has been evaluated. Under open circuit conditions and 60 vol.% AH, the cell polarization resistance, RP is as low as 0.26 Ω cm2 at 900 °C. An electrolysis current of 0.88 A cm-2 and a hydrogen production rate as high as 380 mL cm-2 h have been achieved at 900 °C with an electrolysis voltage of 1.3 V and 60 vol.% AH. Further, the cell has demonstrated good stability in the long-term steam electrolysis test. The results showed that the cell electrolysis performance was even better than that of the reported strontium doped lanthanum manganite (LSM) – yttria stabilized zirconia (YSZ)|YSZ|Ni–YSZ cell, indicating that SFM could be a very promising electrode material for the practical application of SOEC technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thin film ceria–bismuth bilayer electrolytes for intermediate temperature solid oxide fuel cells with La0.85Sr0.15MnO3-δ–Y0.25Bi0.75O1.5 cathodes

Thin film electrolytes of bilayer bismuth oxide/ceria are developed for intermediate temperature solid oxide fuel cells. Y0.25Bi0.75O1.5 is deposited via Direct Current magnetron sputtering technique on an Sm0.2Ce0.8O1.90 electrolyte film which is prepared by a dry-pressing process on an NiO–Sm0.2Ce0.8O1.90 substrate. La0.85Sr0.15MnO3-δ–Y0.25Bi0.75O1.5 composite is applied onto the Y0.25Bi0.75O1.5 film as the cathode to form a single cell. Cells with 6-μm-thick Y0.25Bi0.75O1.5 and 26-μm-thick Sm0.2Ce0.8O1.90 bilayer electrolytes exhibit improved open circuit voltages and power density compared with those obtained with only Sm0.2Ce0.8O1.90 electrolytes. The open circuit voltages are comparable and power densities are higher than those previously reported for solid oxide fuel cells with thick bilayer electrolytes using noble metals such as Pt as the electrodes. Impedance spectra show that the change of electrolyte resistance is negligible while the cathodic interfacial polarization resistance decreased significantly when the Y0.25Bi0.75O1.5 layer is added to form the Sm0.2Ce0.8O1.90/Y0.25Bi0.75O1.5 bilayer electrolytes.

36 MATERIALS SCIENCE↗