Optically Triggered Nucleation Eliminates Hydration Hysteresis in Swelling Minerals
Not Available
Teng, Yuntian (ORCID:0000000193438826)↗
Engineering topics
Chen, Cheng
Publications and source records attributed to Chen, Cheng.
Experimental and numerical investigation of fracture conductivity between non-smooth rock surfaces with and without proppant
The enhancement of fracture conductivity is vital for the efficient recovery of subsurface resources, such as geothermal energy and petroleum hydrocarbons. Proppants, granular materials injected into hydraulic fractures to maintain their conductivity, have been studied primarily in the context of smooth fractures (i.e., fractures between smooth rock surfaces). However, non-smooth fractures (i.e., fractures between rough rock surfaces) are common in geoenergy reservoirs and thus require further investigations. In this study, we conducted laboratory measurements of fracture conductivity on shale slabs with non-smooth surfaces and carried out numerical simulation using the lattice Boltzmann (LB) method, which aimed to investigate the conductivity of non-smooth fractures with and without proppants placement. When ceramic proppant with an areal concentration of 2 lb/ft 2 was placed in the fracture, the conductivity was enhanced by roughly 3-8 times compared to fractures without proppant. In fractures with proppant, gas-measured conductivity was higher than that measured with water due to proppant embedment caused by water. The experiments demonstrate the advantages of using proppant in fractures, even if the rock surface roughness can provide certain fracture conductivity via the self-propping mechanism. For fractures without proppants, high rock surface roughness is not necessarily favorable for enhancing fracture conductivity because the self-propping mechanism requires shear slip along the fracture surface. If there is no shear slip, high rock surface roughness can cause a detrimental effect on the fracture conductivity due to the interlocking effect. Utilizing advanced experimental equipment and LB modeling, this research explores the interplays between proppant placement, fracture geometry, and stress conditions to develop a comprehensive understanding of the productivity in non-smooth fractures. Further, the outcomes of this investigation indicate the importance of creating fractures with surface roughness during hydraulic fracturing and will contribute to the development of more efficient stimulation techniques for subsurface energy extraction.
15 GEOTHERMAL ENERGY↗
Review: Pre-Darcy flows in low-permeability porous media
The widely used Darcy’s law specifies a linear relation between the Darcy velocity of fluid flow and the pressure gradient that drives the flow. However, studies have shown that Darcy velocity can exhibit a nonlinear dependence on the pressure gradient in low-permeability porous media such as clay and shale when the pressure gradient is adequately low. This phenomenon is referred to as low-velocity non-Darcian flow or pre-Darcy flow. This paper provides a comprehensive review of the theories, experimental data, and modeling methods for pre-Darcy flow in low-permeability porous media. The review begins by outlining the fundamental mechanisms underlying pre-Darcy flow that regulate the unique characteristics such as nonlinear dependence of the Darcy velocity on the pressure gradient and its relevance to fluid–rock interactions. The review then proceeds to present a thorough compilation of experimental investigations performed in various low-permeability geomaterials including tight sandstones, shales, and clays. Next, empirical and theoretical models and simulation methods that have been developed to fit and interpret experimental data are reviewed. Finally, the review underscores the challenges encountered in conducting and interpreting pre-Darcy flow experiments and suggests future research directions. By analyzing previous experimental investigations, this review aims to offer a valuable resource for researchers and practitioners seeking to enhance their understanding of fluid dynamics in low-permeability geomaterials. This provides insights into the application of pre-Darcy flow in numerous natural and engineered processes such as shale oil and gas recovery, contaminant transport in low-permeability aquifers, and geological disposal of nuclear waste.
58 GEOSCIENCES↗
Utah FORGE 5-2419: Temperature Testing of Proppants for EGS and Stimulation of Electromagnetic Fracture Mapping Using Electrically-Conducive Proppants - 2024 Annual Workshop Presentation
This is a presentation on the Temperature Testing of Proppants for EGS and Stimulation of Electromagnetic Fracture Mapping Using Electrically-Conducive Proppants by Stevens Institute of Technology, presented by Cheng Chen. This video slide presentation discusses well controlled laboratory experiments testing the high-temperature performance of electrically-conductive and non-electrically-conductive proppants in maintaining fractures hydraulic and electrical conductivities to understand and quantify the thermal-hydrologic-mechanical-chemical mechanisms that regulate the observed behaviors. This will be tested using proppant/fracture imaging via borehole electromagnetic measurements. This presentation was featured in the Utah FORGE R&D Annual Workshop on August 15, 2024.
15 GEOTHERMAL ENERGY↗
Comparative Assessment of U-Net-Based Deep Learning Models for Segmenting Microfractures and Pore Spaces in Digital Rocks
Segmentation of high-resolution X-ray microcomputed tomography (µCT) images is crucial in digital rock physics (DRP), affecting the characterization and analysis of microscale phenomena in the porous media. The complexity of geological structures and nonideal scanning conditions pose significant challenges to conventional image segmentation approaches. Motivated by the recent increasing popularity of deep learning (DL) techniques in image processing, this work undertakes a comparative study of DL models, specifically U-Net and its variants, for segmenting multiple targets with distinguished features in digital rocks, including discrete fracture networks (DFNs), pore spaces, and solid rock. Particularly, DFNs have a smaller volumetric fraction over others, bringing in a substantial challenge of imbalanced segmentation. The primary focus is to evaluate the architecture and feature enhancement strategies of various DL models, including U-Net, attention U-Net, residual U-Net, U-Net++, and residual U-Net++. The models were designed as 2.5D, utilizing a central 2D image and its two adjacent upper and lower 2D images as input to provide a pseudo-3D context. In addition, because the ground truth of segmentation was unknown for real-world digital rocks, we created a benchmark data set following the inverse operations of segmentation. The data synthesis started from the label images (i.e., solid rock, pore spaces, and DFNs), followed by simulating partial volume blurring, adding random background noise, and introducing ring artifacts to mimic real raw X-ray µCT images. The data set, which included various rock types (i.e., sandstone and artificial data), scanning resolution, and magnitudes of noise and artifacts, was divided into training and testing data sets with a 90% and 10% ratio, respectively. Moreover, in addition to the conventional pixel-wise evaluation metrics, the physics-based metric of the lattice-Boltzmann method (LBM) simulated permeability provided more comprehensive assessments. The results demonstrated that the residual connections, nested architectures, and redesigned skip connections contribute to the model performance and give the residual U-Net++ the highest accuracy. The improvements were mainly on the boundaries and small targets, especially the DFNs, which dominate the interconnectivity and therefore affect the permeability greatly. This study also rigorously evaluated the efficiency and generalization of each model, demonstrating that the sophisticated architectures achieved excellent practicability and maintained robust performance on completely unseen data, ensuring their suitability for diverse and challenging DRP applications.
58 GEOSCIENCES↗
Collaborative Autonomous Logistics
This video shows a demonstration of collaborative autonomous logistics. Turtlebot, a 1-g stand-in for Astrobee, carried REALM sensors around a mockup of ISS in ARGOS to autonomously survey for a cargo bag stowed in a drawer. It provided the location of the bag to Robonaut, which then autonomously climbed across the mockup to the drawer. Robonaut then used the Affordance Template manipulation framework to localize and open the drawer and then again localize and retrieve the cargo bag.
Badger, Julia M.↗