Engineering Papers⌕ Search

Engineering topics

Charles R Buhler

Publications and source records attributed to Charles R Buhler.

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Self-Cleaning Coatings for Space or Earth Transparent Electrodynamic Dust Shields Usable for Solar Cells

Reducing dust accumulation on any surface is key for lunar missions as dust can damage or impair the performance of everything from deployable systems to solar cells on the Moon’s surface. Electrodynamic dust shields (EDSs) are a key method to actively clean surfaces by running high voltages (but low currents) through electrodes on the surface. The forces generated by the voltage efficiently remove built up, electrically charged dust particles. Innovators at the NASA Kennedy Space Center have developed a new transparent EDS for removing dust from space and lunar solar cells among other transparent surfaces. The new coatings operate at half the voltage of existing EDSs while being 90% thinner. These capabilities are enabled by an innovative combination of electrode patterning and a thin silica protective layer. The reduced thickness and lower voltage operation expands possibilities for integrating EDSs onto transparent surfaces across industries.

Jerry J Wang↗
NASA NTRS2020

Electrospraying for Precision Delivery of Water and Nutrients for Aeroponics in Microgravity

Developed an enclosure with a custom high voltage nozzle that electrosprays wire "roots" with milliliters (mL) of water in real time by measuring the charge sprayed onto the roots. It uses the spray’s charge to mass from previous measurements with the same nozzle (and the density of water) to convert the display to volume. To deliver water to the nozzle consistently and programmatically, the syringe pump performed the best for experiments because the diaphragm pump created a stuttered flow and the pressurized reservoir’s pressure controller was more complex than the syringe pump’s commercial LabVIEW software that direct controls flow rate.

Joel D Malissa↗
NASA NTRSDate not supplied

Evaluation of Coatings for the Electrodynamic Dust Shield Application on Thermal Radiators

Dust acts as a blackbody, becoming hot if left in direct sunlight. This is a problem for thermal radiators where the main function is to radiate heat away from an object. If dust lands on the thermal radiator, the unit will less effectively reject heat, and it will overheat. This can lead to electrical or system failure. The current state-of-the-art in active dust mitigation is the Electrodynamic Dust Shield (EDS) which uses an electric field generated by alternating high positive and negative voltages (low current) to eject the charged dust off surfaces. An EDS made from copper coated Kapton is an ideal candidate to be bonded to a thermal radiator and coated with a low solar absorptance, high heat-emitter coating. This work compares the dust removal of copper-Kapton EDSs covered with different thermal radiator coatings in air and vacuum environments. The coatings include AZ-93 paint, Thermal Bright, and Solar White, a coating developed by the Applied Physics Lab (APL) at NASA Kennedy Space Center (KSC). The resistance and the thickness of the various coatings impact how well it works as an insulative layer for the EDS. Preliminary results indicate that Solar White may have better properties for dust removal and thermal rejection than the other coatings.

Krystal L Acosta↗
NASA NTRSDate not supplied

EDS to the Moon!

The Electrostatics and Surface Physics Laboratory at NASA Kennedy Space Center is slated to send multiple Electrodynamic Dust Shields (EDS) to the surface of the moon. This paper discusses the EDS onboard a Commercial Lunar Payload System or CLPS mission slated to launch to the moon on July 27, 2023 on Firefly Aerospace’s Blue Ghost Lander to Mare Crisium. The EDS payload consists of a camera EDS, a separate glass EDS, a thermal radiator EDS as well as a Re-Duster system based on EDS technology. The EDS will be deposited on the ground by a deployable structure on the lunar lander shortly after touchdown and its operations will take precedence over the other 10 payloads on the lander. The camera will record images and videos of dust deposition and removal on both the Thermal Radiator EDS and the Glass EDS. Data handling will be done using a Data Storage Unit (DSU) developed by NASA Langley Research Center and downlinked to Earth in real time.

Charles R Buhler↗
NASA NTRSDate not supplied

Electrostatic Charging of the Lunar Surface

Lunar regolith dust particles accumulate charge and interact electrostatically with rover wheels, astronaut boots, and equipment. We have developed instrumentation for in situ measurements of the electrostatic charge developed by the interactions of lunar regolith dust with the space-rated materials on these devices. This instrument is also capable of measuring the distribution of electric fields on or near the lunar surface and the ion currents present near the lunar surface. We also report on our efforts to characterize the charging behavior of lunar dust in low gravity environments. This behavior is nonintuitive due to complex interactions between individual dust grains. We are developing an experiment to study this interaction in a microgravity vacuum environment. Better understanding of this interaction will allow for improved dust mitigation on the lunar surface.

electrostatics↗
NASA NTRSDate not supplied

Evaluation of Coatings for the Electrodynamic Dust Shield Application on Thermal Radiators

Space dust acts as a blackbody, becoming hot if left in direct sunlight. This is a problem for thermal radiators used in space missions, where the main function is to radiate heat away from an object. If dust lands on the thermal radiator, the unit will less effectively reject heat, and it will overheat, leading to electrical or system failure. The current state-of-the-art in active dust mitigation is the Electrodynamic Dust Shield (EDS) which uses an electric field generated by alternating high positive and negative voltages (low current) to eject the charged dust off surfaces. An EDS made from copper coated Kapton is an ideal candidate to be bonded to a thermal radiator and coated with a low solar absorptance, high heat-emitter coating. This work compares the dust removal of copper-Kapton EDSs covered with different thermal radiator coatings in air and vacuum environments. The coatings include AZ-93 paint, Thermal Bright, and Solar White, a coating developed by the Applied Physics Lab (APL) at NASA Kennedy Space Center (KSC). The resistance and the thickness of the various coatings impact how well it works as an insulative layer for the EDS. Preliminary results indicate that Solar White may have better properties for dust removal and thermal rejection than the other coatings.

Krystal L. Acosta↗
NASA NTRSDate not supplied

New Methods to Determine the Electromagnetic Effects from Precipitation Static

The Electrostatics and Surface Physic Laboratory has devised a new method to determine the electromagnetic effects from precipitation static or p-static as its commonly called. P-static occurs as a result of triboelectric charging of granular materials or ice crystals bombarded onto the surfaces of air and/or space vehicles at high speeds. The electrostatic charge that builds up on the outer surface can have deleterious effects that arise during discharge events. These discharges can cause loss of communication to and from the vehicle from ground stations, EMI interference, radio frequency noise, etc… There are even cases of total loss of vehicles caused by p-static charging. We have developed a method to simulate the extensive tribocharging of insulating materials that occurs during p-static through the use of corona charging which allows testing to occur within a lab environment. These tests simulate the discharges that occur on rocket vehicles during ascent as a result of gas breakdown by performing the corona charging tests inside a vacuum chamber and subsequently removing the air. The simultaneous gas discharges emit electromagnetic interference (EMI) which can be captured and monitored.

Charles R Buhler↗
NASA NTRSDate not supplied

Swamp Works Technology Development 10th Anniversary: 2013-2023

Kennedy Space Center’s (KSC) Swamp Works, provides government and commercial space ventures with the technologies required for working and living on the surfaces of the Moon or other planets and bodies in our solar system. The Swamp Works team establishes efficient, innovative and cost-effective exploration mission solutions through leveraging of partnerships across NASA, industry and academia. Concepts start small and build up momentum, with lean development processes and a hands-on approach. Testing is performed in early stages to drive design improvements and progressively increase Technology Readiness Levels (TRL). Swamp Works provides concepts, architecture studies and trades, designs, data, technology development, technology demonstration hardware, flight hardware, testing, flight support and knowledge in support of the development of surface systems. It consists of several teams with associated laboratories and test capabilities. The Granular Mechanics and Regolith Operations (GMRO) Laboratory and the Electrostatics and Surface Physics Laboratory (ESPL) are co-located in the Engineering Development Lab (EDL) facility high bay. The Applied Chemistry Lab (ACL) is in an adjacent facility and other KSC labs are being influenced by the innovation methods pioneered at the Swamp Works. The Swamp Works was founded in January 2013 by a group of scientists and engineers at KSC with the over-arching vision of expanding humanity and civilization into the solar system by the use of space resources via advanced technology. Ultimately, this will create a solar system economy that will improve the human condition due to the abundance of energy and resources. This presentation will summarize the projects and technology development that have been performed by the Swamp Works to celebrate its 10th Anniversary of innovation success.

Swamp Works↗
NASA NTRSDate not supplied

Monodisperse Single-Material Granular Tribocharging Modeling and Experimental Validation

Charge transfer between insulating grains has been a topic of interest for many years as this phenomenon is extremely important to many areas in industry. Of particular interest to NASA is the behavior of electrically insulative dust grains such as those found on the lunar surface. Whether poured from a scoop during sample collection activities, agitated inside a drum via mining robots, or fluidized by a gas plume, particle-particle interactions between similar granular materials will be widespread on the Moon. Designers hope to have a predictive model for how dust grains are charged, transported, and deposited on flight systems to better understand issues electrostatics may cause in future missions. While difference in work function is often seen as a driver for charge transfer between two materials, this is an incomplete representation for insulative particles. Other asymmetries in the system can also lead to charge being transferred: one such being the difference between static vs dynamic particles. Experiments performed under vacuum in the Electrostatics and Surface Physics Laboratory (ESPL) clearly show that particles having more contacts with other particles tend to charge positively and particles having fewer contacts tend to charge negatively, despite being made from the same material. During these experiments, monodisperse (population of single diameter) spherical particles were held in a reservoir which was then elevated at one end to slope into a Faraday cup used to measure bulk charge of the grains. Care was taken to limit the number of spheres bouncing out of the cup, to isolate the beads from the container itself so that only grain-to-grain interactions occurred, and to assure neutrality of the beads before the experiment began. A discrete element method (DEM) modeling package already incorporating many granular mechanics interactions was augmented to include the electrostatic behaviors seen in experiments. The model can reproduce the experimental results above by tracking the number of contacts between pairs of individual grains and applying a charge transfer condition related to this contact parameter. The experimental results as well as their incorporation into the improved modeling suite will be discussed. Future work includes adding additional asymmetries into the experiments/model such as polydisperse populations of spherical particles and irregularly shaped grains.

granular↗