Engineering Papers⌕ Search

Engineering topics

Chandross, Michael

Publications and source records attributed to Chandross, Michael.

At least 37 records · Page 2

Stress- and Time-Dependent Formation of Self-Lubricating In Situ Carbon (SLIC) Films on Catalytically-Active Noble Alloys

Abstract Low shear strength (30 MPa) organic films were grown in situ on Pt 0.9 Au 0.1 surfaces via cyclic sliding contact in dry N 2 with trace concentrations of ambient hydrocarbons. We present a systematic investigation of the stress- and time-dependent film formation. Steady-state friction coefficients were found to be as low as µ ~ 0.015 and inversely proportional to contact pressure, revealing non-Amontonian behavior. Above a Hertzian contact pressure of ~500 MPa, shear strength dropped, indicating an activated process. Raman spectroscopy identified non-uniformity in areal coverage and relative order with contact pressure. Regions of steady-state low-friction behavior exhibited spectra similar to DLC coatings. Atomic force microscopy was used to study the formation and growth of films at the nanoscale. Stress- and time-dependent measurements suggested a sublinear increase of film volume with time, and a transition from growth to wear at a Hertzian contact pressure of ~1.2 GPa.

Jones, Morgan R.↗

Friction of Metals: A Review of Microstructural Evolution and Nanoscale Phenomena in Shearing Contacts

The friction behavior of metals is directly linked to the mechanisms that accommodate deformation. We examine the links between mechanisms of strengthening, deformation, and the wide range of friction behaviors that are exhibited by shearing metal interfaces. Specifically, the focus is on understanding the shear strength of nanocrystalline and nanostructured metals, and conditions that lead to low friction coefficients. Grain boundary sliding and the breakdown of Hall–Petch strengthening at the shearing interface are found to generally and predictably explain the low friction of these materials. While the following is meant to serve as a general discussion of the strength of metals in the context of tribological applications, one important conclusion is that tribological research methods also provide opportunities for probing the fundamental properties and deformation mechanisms of metals.

36 MATERIALS SCIENCE↗

Formation of Coherent 1H–1T Heterostructures in Single-Layer MoS 2 on Au(111)

Heterojunctions of semiconductors and metals are the fundamental building blocks of modern electronics. Coherent heterostructures between dissimilar materials can be achieved by composition, doping, or heteroepitaxy of chemically different elements. Here, we report the formation of coherent single-layer 1H–1T MoS 2 heterostructures by mechanical exfoliation on Au(111), which are chemically homogeneous with matched lattices but show electronically distinct semiconducting (1H phase) and metallic (1T phase) character, with the formation of these heterojunctions attributed to a combination of lattice strain and charge transfer. The exfoliation approach employed is free of tape residues usually found in many exfoliation methods and yields single-layer MoS 2 with millimeter (mm) size on the Au surface. Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning tunneling microscopy (STM), and scanning tunneling spectroscopy (STS) have collectively been employed to elucidate the structural and electronic properties of MoS 2 monolayers on Au substrates. Bubbles in the MoS 2 formed by the trapping of ambient adsorbates beneath the single layer during deposition, have also been observed and characterized. Lastly, our work here provides a basis to produce two-dimensional heterostructures which represent potential candidates for future electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evidence of Inverse Hall-Petch Behavior and Low Friction and Wear in High Entropy Alloys

We present evidence of inverse Hall-Petch behavior for a single-phase high entropy alloy (CoCrFeMnNi) in ultra-high vacuum and show that it is associated with low friction coefficients (~0.3). Grain size measurements by STEM validate a recently proposed dynamic amorphization model that accurately predicts grain size-dependent shear strength in the inverse Hall-Petch regime. Wear rates in the initially soft (coarse grained) material were shown to be remarkably low (~10 –6 mm 3 /N-m), the lowest for any HEA tested in an inert environment where oxidation and the formation of mixed metal-oxide films is mitigated. The combined high wear resistance and low friction are linked to the formation of an ultra-nanocrystalline near-surface layer. The dynamic amorphization model was also used to predict an average high angle grain boundary energy (0.87 J/m 2 ). This value was used to explain cavitation-induced nanoporosity found in the highly deformed surface layer, a phenomenon that has been linked to superplasticity.

36 MATERIALS SCIENCE↗

Low friction in bcc metals via grain boundary sliding

In this work, low friction is demonstrated with pure polycrystalline tantalum sliding contacts in both molecular dynamics simulations and ultrahigh vacuum experiments. This phenomenon is shown to be correlated with deformation occurring primarily through grain boundary sliding and can be explained using a recently developed predictive model for the shear strength of metals. Specifically, low friction is associated with grain sizes at the interface being smaller than a critical, material-dependent value, where a crossover from dislocation mediated plasticity to grain-boundary sliding occurs. Low friction is therefore associated with inverse Hall-Petch behavior and softening of the interface. Direct quantitative comparisons between experiments and atomistic calculations are used to illustrate the accuracy of the predictions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Achieving high strength and ductility in traditionally brittle soft magnetic intermetallics via additive manufacturing

Intermetallic alloys possess exceptional soft magnetic properties, including high permeability, low coercivity, and high saturation induction, but exhibit poor mechanical properties that make them impractical to bulk process and use at ideal compositions. We used laser-based Additive Manufacturing to process traditionally brittle Fe–Co and Fe–Si alloys in bulk form without macroscopic defects and at near-ideal compositions for electromagnetic applications. The binary Fe–50Co, as a model material, demonstrated simultaneous high strength (600–700 MPa) and high ductility (35%) in tension, corresponding to a ~300% increase in strength and an order-of-magnitude improvement in ductility relative to conventionally processed material. Atomic-scale toughening and strengthening mechanisms, based on engineered multiscale microstructures, are proposed to explain the unusual combination of mechanical properties. Here, this work presents an instance in which metal Additive Manufacturing processes are enabling, rather than limiting, the development of higher-performance alloys.

36 MATERIALS SCIENCE↗

Mechanical and Corrosion Properties of Additively Manufactured CoCrFeMnNi High Entropy Alloy

Here, this study investigates the mechanical and corrosion properties of as-built and annealed equiatomic CoCrFeMnNi alloy produced by laser-based directed energy deposition (DED) Additive Manufacturing (AM). The high cooling rates of DED produced a single-phase, cellular microstructure with cells on the order of 4 μm in diameter and inter-cellular regions that were enriched in Mn and Ni. Annealing created a chemically homogeneous recrystallized microstructure with a high density of annealing twins. The average yield strength of the as-built condition was 424 MPa and exceeded the annealed condition (232 MPa), however; the strain hardening rate was lower for the as-built material stemming from higher dislocation density associated with DED parts and the fine cell size. In general, the yield strength, ultimate tensile strength, and elongation-to-failure for the as-built material exceeded values from previous studies that explored other AM techniques to produce the CoCrFeMnNi alloy. Ductile fracture occurred for all specimens with dimple initiation associated with nanoscale oxide inclusions. The breakdown potential (onset of pitting corrosion) was similar for the as-built and annealed conditions at 0.40 V Ag/AgCl when immersed in 0.6 M NaCl. Pit morphology/propagation for the as-built condition exhibited preferential corrosion of inter-cellular Ni/Mn regions leading to a tortuous pit bottom and cover, while the annealed conditions pits resembled lacy pits similar to 304 L steel. Lastly, a passive oxide film depleted in Cr cations with substantial incorporation of Mn cations is proposed as the primary mechanism for local corrosion susceptibility of the CoCrFeMnNi alloy.

36 MATERIALS SCIENCE↗

Continuum stress intensity factors from atomistic fracture simulations

Stress intensity factors (SIFs) are utilized in continuum fracture mechanics to quantify the stress fields surrounding a crack in a homogeneous material in the linear elastic regime. Critical values of the SIFs define an intrinsic measure of the resistance of a material to propagate a crack. At atomic scales, yet, fracture occurs as a series of atomic bonds breaking, differing from the continuum description. As a consequence, a formal analog of the continuum SIFs calculated from atomistic simulations can have spatially localized, microstructural contributions that originate from varying bond configurations. The ability to characterize fracture at the atomic scale in terms of the SIFs offers both an opportunity to probe the effects of chemistry, as well as how the addition of a microstructural component affects the accuracy. We present a novel numerical method to determine SIFs from molecular dynamics (MD) simulations. The accuracy of this approach is first examined for a simple model, and then applied to atomistic simulations of fracture in amorphous silica. MD simulations provide time and spatially dependent SIFs, with results that are shown to be in good agreement with experimental values for fracture toughness in silica glass.

42 ENGINEERING↗

Achieving Ultralow Wear with Stable Nanocrystalline Metals

Recent work suggests that thermally stable nanocrystallinity in metals is achievable in several binary alloys by modifying grain boundary energies via solute segregation. The remarkable thermal stability of these alloys has been demonstrated in recent reports, with many alloys exhibiting negligible grain growth during prolonged exposure to near-melting temperatures. In this paper, we show that PtAu, a proposed stable alloy consisting of two noble metals, exhibits extraordinary resistance to wear. Ultra-low wear rates, less than a monolayer of material removed per sliding pass, were measured for PtAu thin films at a maximum Hertz contact stress of up to 1.1 GPa. This is the first instance of an all-metallic material exhibiting a specific wear rate on the order of 10 -9 mm 3 /N-m, comparable to diamond-like carbon and sapphire. Remarkably, the wear rate of sapphire and silicon nitride probes used in wear experiments were either higher or comparable to that of the PtAu alloy, despite the substantially higher hardness of the ceramic probe materials. High-resolution microscopy showed negligible surface microstructural evolution in the wear tracks after 100k sliding passes. Finally, mitigation of fatigue-driven delamination enabled a transition to wear by atomic attrition, a regime previously limited to highly wear resistant materials such as diamond-like carbon.

36 MATERIALS SCIENCE↗