Engineering Papers⌕ Search

Engineering topics

Chandler, W. T.

Publications and source records attributed to Chandler, W. T..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Materials for advanced rocket engine turbopump turbine blades

A study program was conducted to identify those materials that will provide the greatest benefits as turbine blades for advanced liquid propellant rocket engine turbines and to prepare technology plans for the development of those materials for use in the 1990 through 1995 period. The candidate materials were selected from six classes of materials: single-crystal (SC) superalloys, oxide dispersion-strengthened (ODS) superalloys, rapid solidification processed (RSP) superalloys, directionally solidified eutectic (DSE) superalloys, fiber-reinforced superalloy (FRS) composites, and ceramics. Properties of materials from the six classes were compiled and evaluated and property improvements were projected approximately 5 years into the future for advanced versions of materials in each of the six classes.

Chandler, W. T.↗
NASA NTRS1979

The role of crack blunting in sustained load crack growth

Sustained load crack growth occurs in metals following critical crack extension above KIc and in aggressive environments while maintaining a constant load below KIc. In this paper, crack arrest measurements are performed on precracked, 0.0254-m thick, side-grooved WOL specimens exposed to 34.5 MN/sq m hydrogen at ambient temperature. The specimens are loaded inside a pressure vessel while in contact with the high pressure hydrogen environment. Crack growth is observed with each loading increment. The crack blunting observed in the fracture mechanics tests on 321 stainless steel is found to be similar to that produced in the 321 stainless steel tensile specimens. Rounding and branching of the crack decreases the effective stress intensity at the crack tip. It is possible, for materials in which cracks tend to blunt or branch in hydrogen, that although cracks will arrest at a relatively high stress intensity in decreasing stress intensity test, a crack may begin to grow at a lower stress intensity when loaded in hydrogen, and the crack may continue to grow when the stress intensity is continually increasing.

Walter, R. J.↗
NASA NTRS1978

Influence of high pressure hydrogen on cyclic load crack growth in metals

The effect of high pressure hydrogen on the crack growth rate of various nickel-base alloys was studied at ambient temperature. Considerable enhancement of the cyclic flaw growth rate was observed for Inconel 718, wrought and cast, and Waspaloy, a nickel-base alloy similar to Inconel 718. Only slight enhancement of the flaw growth rate for Alloy 903 was observed.

Jewett, R. P.↗
NASA NTRS1978

Influence of hydrogen environments on crack growth in Inconel 718

The effect of hydrogen environments on sustained-load and cyclic-load crack growth in Inconel 718 was investigated using fracture-mechanics-type specimens. The sustained-load crack growth was determined to be a function of heat-treatment condition, temperature, and hydrogen pressure. The threshold stress intensity for subcritical crack growth was independent of hydrogen pressure at pressures greater than 21 MN/sq m (3000 psi). The cyclic-load crack growth rate in Inconel 718 at low and moderate stress intensity ranges increased with increasing hydrogen pressure. Decreasing the cyclic frequency from 1.0 to 0.1 Hz considerably increased the cyclic crack growth rate at 0.069 MN/sq m (10 psi) and at 68.9 MN/sq m (10,000 psi) hydrogen pressure. A series of measurements performed between 1.0 and 0.1 Hz showed that the crack growth rate increased as a complex function of the time per cycle.

Walter, R. J.↗
NASA NTRS1978

Hydrogen Embrittlement and Its Control in Hydrogen-Fueled Engine Systems

The nature of hydrogen embrittlement by high pressure gaseous hydrogen is described and methods of designing SSME gaseous hydrogen systems, including techniques of hydrogen embrittlement prevention, are discussed. The effects of gaseous hydrogen environments are emphasized. Results of extensive investigations of gaseous hydrogen environments on metals conducted under the SSME program are presented.

Chandler, W. T.↗
NASA NTRS1976

Cyclic-load crack growth in ASME SA-105 grade II steel in high-pressure hydrogen at ambient temperature

ASME SA-105 Grade II steel, which is used in high-pressure hydrogen compressor systems, is similar to steels used or considered for use in high-pressure hydrogen storage vessels and pipelines. This paper summarizes the results of a program conducted to provide cyclic-load crack growth rate (da/dN) data for a fracture mechanics analysis of a 15,000 psi hydrogen compressor facility which contains pulse quieter and after-cooler separator vessels constructed of the ASME SA-105 Grade II steel. Included in the program were tests performed to assist in establishing operating procedures that could minimize the effect of hydrogen on crack growth rates during operation.

Walter, R. J.↗
NASA NTRS1975

Hydrogen-environment embrittlement of metals and its control

Types of hydrogen embrittlement are discussed together with characteristics of hydrogen-environment embrittlement, the degree of hydrogen-environment embrittlement of a wide variety of alloys, the effect of hydrogen environments on various properties, (tension, fatigue, creep and fracture mechanics), and the influence of hydrogen exposure parameters on the degree of embrittlement. Design methods for high-pressure hydrogen service and for prevention of hydrogen-environment embrittlement are also covered.

Chandler, W. T.↗
NASA NTRS1974

Influence of gaseous hydrogen on Inconel 718

The embrittlement of Inconel 718 by exposure to 34.5 MN/sq m hydrogen at ambient temperature was found to be a function of both forming operation and heat treatment. The embrittlement, as measured by reduction of notch strength in hydrogen as compared to helium, was decreased by a fine-grain size and was most severe for coarse-grained structures containing a continuous or nearly continuous precipitate tentatively identified as Ni3Cb. Tests performed on unnotched specimens showed that the strain at which surface cracks initiate in 34.5 MN/sq m hydrogen was approximately 3% and was independent of prior forming operation or heat treatment.

Walter, R. J.↗
NASA NTRS1973

Influence of gaseous hydrogen on metals

Tensile, fracture toughness, threshold stress intensity for sustained-load crack growth, and cyclic and sustained load crack growth rate measurements were performed on a number of alloys in high-pressure hydrogen and helium environments. The results of tensile tests performed in 34.5 MN/m2 (5000 psi) hydrogen indicated that Inconel 625 was considerable embrittled at ambient temperature but was not embrittled at 144 K (-200 F). The tensile properties of AISI 321 stainless steel were slightly reduced at ambient temperature and 144 K (-200 F). The tensile properties of Ti-5Al-2.5 Sn ELI were essentially unaffected by hydrogen at 144 K (-200 F). OFHC copper was not embrittled by hydrogen at ambient temperature or at 144 K (-200 F).

Walter, R. J.↗
NASA NTRS1973

Hydrogen-environment embrittlement of metals: A study

Study includes extensive tests examining effects of hydrogen environment on different high-strength metals and alloys. Recommendations for preventing metal failure include use of hydrogen-resistant coatings and inhibitors. Study includes references to related investigations and discussion of work in progress.

Chandler, W. T.↗
NASA NTRS1973

Hydrogen environment embrittlement of metals

Hydrogen environment embrittlement refers to metals stressed while exposed to a hydrogen atmosphere. Tested in air, even after exposure to hydrogen under pressure, this effect is not observed on similar specimens. Much high purity hydrogen is prepared by evaporation of liquid hydrogen, and thus has low levels for potential impurities which could otherwise inhibit or poison the absorbent reactions that are involved. High strength steels and nickel-base allows are rated as showing extreme embrittlement; aluminum alloys and the austenitic stainless steels, as well as copper, have negligible susceptibility to this phenomenon. The cracking that occurs appears to be a surface phenomenon, is unlike that of internal hydrogen embrittlement.

Jewett, R. P.↗
NASA NTRS1970

Low-temperature embrittlement of Ti-6Al-4V and Inconel-718 by high pressure hydrogen

Notched specimens of titanium alloy and Inconel-718 exhibit little reduction of notch strength at certain low temperatures under 2000 lb/sq in. hydrogen, unnotched specimens are not embrittled at these temperatures. The degree of Inconel-718 embrittlement is lower than earlier observations under 1000 lb/sq in. hydrogen.

Chandler, W. T.↗
NASA NTRS1970

Effects of hydrogen on ELI titanium alloy Ti-5Al-2.5Sn

Tensile tests on titanium alloy, following abrasion under hydrogen and temperature cycling, reveal lowered tensile strength, increased ductility, and no embrittlement. Fretting the metal on itself in flowing hydrogen or abrading with an iron file in flowing hydrogen produces titanium hydride.

Chandler, W. T.↗
NASA NTRS1970

Effects of high pressure hydrogen on metals

Hydrogen environment embrittlement causes failure of hydrogen storage vessels at and below design pressures of 5000 to 6000 psi. Investigation of thirty-five alloys determines their susceptibility to such embrittlement.

Chandler, W. T.↗