Engineering topics

Caspi, S.

Publications and source records attributed to Caspi, S..

6 records

NASA NTRS1990

Superfluid transport and its applications in space

Various transport modes in superfluid helium are discussed. They include zero net mass flow and finite mass flow for pure superfluid and normal fluid flow. An attempt is made to characterize these transport modes in a common frame of reference. Two dimensionless numbers are used, namely, the dimensionless heat flux number and the dimensionless driving force number. The equations are generalized by the use of a characteristic length so that they can be applied to the transport of HE II in any geometry. The theories are then extended to applications in space. In particular, fountain effect pumps and superfluid management at zero g by vapor-liquid phase separators are discussed in detail.

Yuan, S. W. K.↗

NASA NTRS1987

Stability and refrigeration of magnet cryosystems near 1.8 K using the thermomechanical effect

Magnet cryosystem options utilizing the thermomechanical effect of He II and the mechano-caloric effect for refrigeration (referred to as vortex refrigeration) are examined. The performance of the existing He II magnet refrigeration system is briefly reviewed, with attention given to superleak properties, vortex shedding, heat input, and thermodynamic cycle. It is concluded that the possibilities of magnet heat leak use for energetics and stability improvements are promising when He II is selected as magnet coolant.

Frederking, T. H. K.↗

NASA NTRS1980

Cryogenic-coolant He4-superconductor dynamic and static interactions

A composite superconducting material (NbTi-Cu) was evaluated with emphasis on post quench solid cooling interaction regimes. The quasi-steady runs confirm the existence of a thermodynamic limiting thickness for insulating coatings. Two distinctly different post quench regimes of coated composites are shown to relate to the limiting thickness. Only one regime,, from quench onset to the peak value, revealed favorable coolant states, in particular in He2. Transient recovery shows favorable recovery times from this post quench regime (not drastically different from bare conductors) for both single coated specimens and a coated conductor bundle.

Caspi, S.↗

NASA NTRS1979

Cryostatic influence of Formvar coatings on sizing of the stabilizer in superconductive NbTi-Cu - Conductor bundle effects

In continuation of single-conductor studies, quench onset data of quasi-steady operation are reported for a Formvar-coated composite (Nb48Ti/Cu) in bundle geometry (conductor thickness about 0.2 cm, approximately square cross section). Overall thermal conductances of the heater simulation technique applied are of the order 0.1 W/(sq cm-K), comparable to single-specimen results, around 4 K and below the lambda transition in agreement with model predictions. Considerable deterioration, however, occurs below 3 K and down to the lambda temperature during operation in near-saturated He I. Consequences for magnets of intermediate energy density are discussed with emphasis on the modifications necessitated by coatings.

Caspi, S.↗

NASA NTRS1978

Cryogenic-coolant He-4-superconductor interaction

The thermodynamic and thermal interaction between a type 2 composite alloy and cryo-coolant He4 was studied with emphasis on post quench phenomena of formvar coated conductors. The latter were investigated using a heater simulation technique. Overall heat transfer coefficients were evaluated for the quench onset point. Heat flux densities were determined for phenomena of thermal switching between a peak and a recovery value. The study covered near saturated liquid, pressurized He4, both above and below the lambda transition, and above and below the thermodynamic critical pressure. In addition, friction coefficients for relative motion between formvar insulated conductors were determined.

Caspi, S.↗

NASA NTRS1978

Cryostatic influence of formvar coatings on sizing of the stabilizer in composite NbTi-Cu superconductors

Often undesirable low energy densities are associated with extreme safety measures (e.g. cryostatic stability) in large superconducting magnets. Therefore, a medium-sized, formvar-coated composite NbTi alloy, Cu-stabilized, has been studied (48 filaments, approximately square cross section about 1/5 cm thickness). Thermal quench behavior (caused by heating) was investigated in various fluid states of He4, including pressurized and superfluid He4. The data obtained support existence of a particular coating thickness ('limiting' thickness) with the property that thermal boundary conditions of uncoated superconductors at a quench are not deteriorated.

Caspi, S.↗