Engineering Papers⌕ Search

Engineering topics

Carver, Keith

Publications and source records attributed to Carver, Keith.

23 records · Page 2

Hypervelocity Impact of Additively Manufactured A356/316L Interpenetrating Phase Composites

We have examined the hypervelocity impact response of targets made from monolithic A356 and 316L, as well as an additively manufactured A356/316L interpenetrating phase composite. 1.9 mm diameter spherical projectiles made from 2017 aluminum were fired at velocities of 5.9-6.1 km/s, allowing for the observation of multiple types of macro- and microstructural damage within each target. The macroscopic cratering damage to the A356/316L composite resembles that of the A356, but observations of both the cross section and the microstructural damage suggest that the A356/316L composite may be more resistant to spalling than A356 shielding with the same areal density.

French, Matthew↗

Additive Manufacturing of Advanced High Temperature Masking Fixtures for EBPVD TBC Coating

The purpose of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Praxair Surface Technologies, Inc. (PST) and Oak Ridge National Laboratory (ORNL) was to develop an additive manufacturing process to fabricate next generation high temperature masking fixtures for coating of turbine airfoils with ceramic Thermal Barrier Coatings (TBC) by the Electron Beam Physical Vapor Deposition (EBPVD) process. Typical masking fixtures are sophisticated designs and require complex part manipulation in order to achieve the desired coating distribution. Fixtures are typically fabricated from high temperature nickel (Ni) based superalloys. The fixtures are fabricated from conventional processes by welding of thin sheet material into a complex geometry, to decrease the weight load for the manipulator and to reduce the thermal mass of the fixture. Recent attempts have been made in order to fabricate the fixtures through casting, but thin walled sections are difficult to cast and have high scrap rates. This project focused on understanding the potential for fabricating high temperature Ni based superalloy fixtures through additive manufacturing. Two different deposition processes; electron beam melting (EBM) and laser powder bed fusion were evaluated to determine the ideal processing route of these materials. Two different high temperature materials were evaluated. The high temperature materials evaluated were Inconel 718 and another Ni base alloy, designated throughout the remainder of this document as Alloy X, as the alloy composition is sensitive. Inconel 718 is a more widely utilized material for additive manufacturing although it is not currently the material utilized for current fixtures. Alloy X is the alloy currently used for the fixtures, but is not a commercially available alloy for additive manufacturing. Praxair determined it was possible to build the fixture using laser powder bed technology from Inconel 718. ORNL fabricated the fixture geometry using the EBM technology in order to compare deposition features such as surface roughness, geometric accuracy, deposition rate, surface and subsurface porosity, and material quality. It was determined that the laser powder bed technology was ideal for the geometry and requirements of the fixture set by Praxair, and Praxair moved forward with the purchase of a laser powder bed system. The subsequent portion of the project focused on determining the ideal processing parameters for alloy X for the laser powder bed system using ORNL’s Renishaw laser powder bed system. Praxair supplied gas atomized powders of alloy X material with properties specified by ORNL. ORNL printed text cube arrays in order to determine the ideal combination of laser powder and laser travel speed in order to maximize material density, improve surface quality, and maintain geometric accuracy. Additional powder supplied by Praxair was used to fabricate a full-scale fixture component.

42 ENGINEERING↗

Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing

The purpose of the proposed project between Cummins and ORNL is to significantly reduce the cost of the tooling (machining and materials) required to create injection molds to make plastic components. Presently, the high cost of this tooling forces the design decision to make cast aluminum parts because Cummins typical production volumes are too low to allow injection molded plastic parts to be cost effective with the amortized cost of the injection molding tooling. In addition to reducing the weight of components, polymer injection molding allows the opportunity for the alternative cooling methods, via nitrogen gas. Nitrogen gas cooling offers an environmentally and economically attractive cooling option, if the mold can be manufactured economically. In this project, a current injection molding design was optimized for cooling using nitrogen gas. The various components of the injection mold tooling were fabricated using the Renishaw powder bed laser additive manufacturing technology. Subsequent machining was performed on the as deposited components to form a working assembly. The injection mold is scheduled to be tested in a projection setting at a commercial vendor selected by Cummins.

36 MATERIALS SCIENCE↗

Evaluation Of Electrochemical Machining Technology For Surface Improvements In Additive Manufactured Components

ORNL Manufacturing Demonstration Facility worked with ECM Technologies LLC to investigate the use of precision electro-chemical machining technology to polish the surface of parts created by Arcam electron beam melting. The goals for phase one of this project have been met. The project goal was to determine whether electro-chemical machining is a viable method to improve the surface finish of Inconel 718 parts fabricated using the Arcam EBM method. The project partner (ECM) demonstrated viability for parts of both simple and complex geometry. During the course of the project, detailed process knowledge was generated. This project has resulted in the expansion of United States operations for ECM Technologies.

42 ENGINEERING↗

The EOS SAR program

The goal of the Spaceborne Imaging Radar (SIR) program is to develop a multipolarization, multifrequency synthetic aperture radar (SAR) with variable imaging geometry which will be ready for flight on the Earth Observing System (EOS) in the mid 1990's. Nominally, this SAR will be a three frequency (L-, C- and X-band) system with quad-polarization available for the L- and C-bands and dual polarization for the X-band system. It will be capable of acquiring multiincidence angle data using electronic beam steering and other imaging geometries by mechanically pitching, yawing and rolling the antenna. The EOS SAR will play a key role along with the other EOS instruments in understanding the earth as a system.

Cimino, Jobea↗