Engineering Papers⌕ Search

Engineering topics

Carman, Gregory P.

Publications and source records attributed to Carman, Gregory P..

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Magnetic state switching in FeGa microstructures

This work demonstrates that magnetoelectric composite heterostructures can be designed at the length scale of 10µms that can be switched from a magnetized state to a vortex state, effectively switching the magnetization off, using electric field induced strain. This was accomplished using thin film magnetoelectric heterostructures of Fe 81.4 Ga 18.6 on a single crystal (011) [Pb(Mg 1/3 Nb 2/3 )O 3 ] 0.68 -[PbTiO 3 ] 0.32 (PMN-32PT) ferroelectric substrate. Here, the heterostructures were tripped from a multi-domain magnetized state to a flux closure vortex state using voltage induced strain in a piezoelectric substrate. FeGa heterostructures were deposited on a Si-substrate for superconducting quantum interference device magnetometry characterization of the magnetic properties. The magnetoelectric coupling of a FeGa continuous film on PMN-32PT was characterized using a magneto optical Kerr effect magnetometer with bi-axial strain gauges, and magnetic multi-domain heterostructures were imaged using x-ray magnetic circular dichroism—photoemission electron microscopy during the transition to the vortex state. The domain structures were modelled using MuMax 3 , a micromagnetics code, and compared with observations. The results provide considerable insight into designing magnetoelectric heterostructures that can be switched from an ‘on’ state to an ‘off’ state using electric field induced strain.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Non-degenerate parametric mixing and Q-enhancement in ALN Lamb wave resonator

In this Letter, we explore a non-degenerate phase independent parametric quality factor (Q)-enhancement technique for aluminum nitride (AlN) Lamb wave resonators. Unlike other active Q-enhancement techniques which require precise phase control of the electronic feedback loop, this technique is implemented by parametrically pumping AlN material stiffness to realize a negative resistance seen at the signal path. The negative resistance is dependent on the nonlinear material modulation and multi-resonance coupling in the device. A nonlinear circuit model is developed to simulate the parametric coupling of each resonance and extract the nonlinearity of AlN from experimental data. With proper pump frequency and pump power, the device quality factor is boosted in both simulation and experiment. The demonstrated Q-enhancement method is simple to implement and can be applied to other types of resonators that have nonlinear behavior and support multi-resonance operation.

42 ENGINEERING↗
DOE OSTI2021

Localized strain profile in surface electrode array for programmable composite multiferroic devices

In this work, we investigate localized in-plane strains on the microscale, induced by arrays of biased surface electrodes patterned on piezoelectrics. Particular focus is given to the influence that adjacent electrode pairs have on one another to study the impact of densely packed electrode arrays. We present a series of X-ray microdiffraction studies to reveal the spatially resolved micrometer-scale strain distribution. The strain maps with micrometer-scale resolution highlight how the local strain profile in square regions up to 250 x 250 lm 2 in size is affected by the surface electrodes that are patterned on ferroelectric single-crystal [Pb(Mg 1/3 Nb 2/3 )O 3 ] x -[PbTiO 3 ] 1-x . The experimental measurements and simulation results show the influence of electrode pair distance, positioning of the electrode pair, including the angle of placement, and neighboring electrode pair arrangements on the strength and direction of the regional strain. Our findings are relevant to the development of microarchitected strain-mediated multiferroic devices. The electrode arrays could provide array-addressable localized strain control for applications including straintronic memory, probabilistic computing platforms, microwave devices, and magnetic-activated cell sorting platforms.

42 ENGINEERING↗
DOE OSTI2021

Rare-earth orbital moment contributions to the magnetic anisotropy in magnetostrictive Tb0.3Dy0.7Fe2

Soft x-ray Magnetic Circular Dichroism spectroscopy at the Dy and Tb M4,5 and the Fe L2,3 edges was performed on a sputter deposited polycrystalline Terfenol-D (Tb0.3Dy0.7Fe2) film on sapphire substrates at temperatures from 100 to 300 K to evaluate the elementwise contribution to the magnetocrystalline anisotropy and coercive field. The elemental spin and orbital magnetic moments were calculated using the x-ray Magnetic Circular Dichroism sum rules. As temperatures decreased, the Tb and Fe moments plateau at 200 K with values of 7.6 μB/atom and 1.8 μB/atom, respectively, while the Dy moment increases to 8.9 μB/atom at 100 K. Between 300 and 200 K, the change in magnetic anisotropy is dominated by thermally induced magnetoelastic effects while for temperatures below 200 K magnetocrystalline anisotropy (MCA) changes are dominant. The MCA changes below 200 K appear to be due to increases in the Dy orbital moment with decreasing temperature in this temperature regime.

Shirazi, Paymon (ORCID:0000000256954597)↗
DOE OSTI2021

Single‐Domain Multiferroic Array‐Addressable Terfenol‐D (SMArT) Micromagnets for Programmable Single‐Cell Capture and Release

Abstract Programming magnetic fields with microscale control can enable automation at the scale of single cells ≈10 µm. Most magnetic materials provide a consistent magnetic field over time but the direction or field strength at the microscale is not easily modulated. However, magnetostrictive materials, when coupled with ferroelectric material (i.e., strain‐mediated multiferroics), can undergo magnetization reorientation due to voltage‐induced strain, promising refined control of magnetization at the micrometer‐scale. This work demonstrates the largest single‐domain microstructures (20 µm) of Terfenol‐D (Tb 0.3 Dy 0.7 Fe 1.92 ), a material that has the highest magnetostrictive strain of any known soft magnetoelastic material. These Terfenol‐D microstructures enable controlled localization of magnetic beads with sub‐micrometer precision. Magnetically labeled cells are captured by the field gradients generated from the single‐domain microstructures without an external magnetic field. The magnetic state on these microstructures is switched through voltage‐induced strain, as a result of the strain‐mediated converse magnetoelectric effect, to release individual cells using a multiferroic approach. These electronically addressable micromagnets pave the way for parallelized multiferroics‐based single‐cell sorting under digital control for biotechnology applications.

Khojah, Reem↗
NASA NTRS2016

Magneto-Optic Field Coupling in Optical Fiber Bragg Gratings

The invention is a magneto-optic coupled magnetic sensor that comprises a standard optical fiber Bragg grating system. The system includes an optical fiber with at least one Bragg grating therein. The optical fiber has at least an inner core and a cladding that surrounds the inner core. The optical fiber is part of an optical system that includes an interrogation device that provides a light wave through the optical fiber and a system to determine the change in the index of refraction of the optical fiber. The cladding of the optical fiber comprises at least a portion of which is made up of ferromagnetic particles so that the ferromagnetic particles are subject to the light wave provided by the interrogation system. When a magnetic field is present, the ferromagnetic particles change the optical properties of the sensor directly.

Carman, Gregory P.↗
NASA NTRS1992

Development of an embedded Fabry Perot Fiber Optic Strain Rosette Sensor (FP-FOSRS)

We investigate the feasibility of utilizing a Fabry-Perot Fiber Optic Strain Rosette Sensor (FP-FOSRS) for the evaluation of the internal strain state of a material system. We briefly describe the manufacturing process for this sensor and point out some potential problem areas. Results of an embedded FP-FOSRS in an epoxy matrix with external resistance strain gauges applied for comparative purposes are presented. We show that the internal and external strain measurements are in close agreement. This work lays the foundation for embedding this sensor in actual composite laminas.

Carman, Gregory P.↗