Engineering Papers⌕ Search

Engineering topics

Capriotti, Luca

Publications and source records attributed to Capriotti, Luca.

At least 73 records · Page 4

Non-Destructive Postirradiation Examination of the AFC-4C Capsule/Rodlet 5 Experiment

The AFC-4C irradiation test was irradiated at the Idaho National Laboratory Advanced Test Reactor to investigate several different fast reactor fuels that could be used to facilitate ultra-high burnup applications in sodium fast reactors. Several different alloys, fuel geometries, bonding materials, and coating/barrier were tested in ferritic-martensitic HT-9 cladding. The AFC-4C capsule 5 was removed from the reactor at around 8.7 at %HM burnup to begin postirradiation examination. This report presents and discusses the non-destructive PIE results of the AFC-4C-capsule / rodlet 5, a U-10Zr solid fuel, sodium bonded with HT9 with internal Cr-coating, and its performance is evaluated against the historical fuel performance of previously irradiated fuel from literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Irradiation performance of nonfertile (Pu-MA-Zr) fast reactor metal fuels

This work was part of a program begun in 2001 to develop advanced nuclear fuels, originally as carriers for plutonium and minor actinides (neptunium, curium, and americium) taken from spent commercial light-water reactors (LWR) so that the plutonium and minor actinides could be ‘burned’ or transmuted in an accelerator or a fast nuclear reactor. A central part of these experiment programs has been the development of advanced fast reactor fuels, because a fast reactor was considered the most efficient vehicle to transmute the actinide waste products, and metallic fuels is a central focus of these tests. An experiment design was developed in which a thermal test reactor, the Advanced Test Reactor (ATR), was used to test small fuel pin prototypes, by creating areas in the core shielded by cadmium filters to produce a largely epithermal and fast neutron spectrum environment in which the pins could be irradiated. The results of non-fertile metallic fuel (no uranium) tests are presented here. Pu-Am-Np-Zr fuels were irradiated to fission densities up to 33 × 10 20 fission/cm 3 and Pu-239 depletions of up to 39%. The depletions were created by roughly 2/3 by fission and 1/3 by transmutation neutron capture. Up to five fuel ‘rodlets’ were irradiated in three sealed capsules stacked axially in the core, and the peak cladding temperatures ranged from 300°C to 500°C, depending on axial location as those near the core centerline are operating hotter and to higher fission densities. Several post-irradiation examinations (precision gamma scanning and fission gas release) were similar to other historical metal fuel experiments in fast reactors. However, optical metallography indicated that two of the rodlets had breached. The exact reasons are unclear. Due to the design of this irradiation experiment a rodlet breach could have increased the temperature in others in the same capsule by contaminating the thermal gap helium with heavier and less conductive fission product gases. Finally, some of those rodlets showed high amounts of fuel/cladding chemical interaction (FCCI).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of a minor actinides bearing metallic fuel pin irradiated in EBR-II

The X501 transmutation experiment irradiated in Experimental Breeder Reactor II (EBR-II) was intended to evaluate the safety and performance of the addition of minor actinides (Am, Np) into the metallic nuclear fuel system. The irradiation of this experiment is also of paramount importance for comparisons between true fast spectrum irradiations (e.g. EBR-II) and shrouded irradiation capsules performed at the thermal neutron spectrum Idaho National Laboratory Advanced Test Reactor. The X501 experimental fuel pins were irradiated to a peak measured burnup of 6.2% fission per initial heavy metal atom. This paper reports and discusses Postirradiation Examination results for one of two minor actinide bearing pins from the EBR-II X-501 experiment (X501-G591) with a focus on fuel microstructure evolution. Additionally, fuel swelling, fission product distribution, cladding strain, fission gas release, fuel microstructure and fuel cladding chemical interaction were all evaluated. The fission gas release was 79.9% and the microstructure along the fuel pin presented several characteristics very similar to other EBR-II U-Pu-Zr ternary metallic fuel experience. Minor actinides seem to not dramatically affect the overall performance of this candidate transmutation fuel. Scanning Electron Microscopy was also performed and an in-depth characterization of the different regions and phases is presented. Performance data from these irradiations can be used to inform the feasibility of minor actinide transmutation in future reactor systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TurboRVB: A many-body toolkit for ab initio electronic simulations by quantum Monte Carlo

TurboRVB is a computational package for ab initio Quantum Monte Carlo (QMC) simulations of both molecular and bulk electronic systems. The code implements two types of well established QMC algorithms: Variational Monte Carlo (VMC) and diffusion Monte Carlo in its robust and efficient lattice regularized variant. A key feature of the code is the possibility of using strongly correlated many-body wave functions (WFs), capable of describing several materials with very high accuracy, even when standard mean-field approaches [e.g., density functional theory (DFT)] fail. The electronic WF is obtained by applying a Jastrow factor, which takes into account dynamical correlations, to the most general mean-field ground state, written either as an antisymmetrized geminal power with spin-singlet pairing or as a Pfaffian, including both singlet and triplet correlations. This WF can be viewed as an efficient implementation of the so-called resonating valence bond (RVB) Ansatz, first proposed by Pauling and Anderson in quantum chemistry [L. Pauling, The Nature of the Chemical Bond (Cornell University Press, 1960)] and condensed matter physics [P.W. Anderson, Mat. Res. Bull 8, 153 (1973)], respectively. The RVB Ansatz implemented in TurboRVB has a large variational freedom, including the Jastrow correlated Slater determinant as its simplest, but nontrivial case. Moreover, it has the remarkable advantage of remaining with an affordable computational cost, proportional to the one spent for the evaluation of a single Slater determinant. Therefore, its application to large systems is computationally feasible. The WF is expanded in a localized basis set. Several basis set functions are implemented, such as Gaussian, Slater, and mixed types, with no restriction on the choice of their contraction. The code implements the adjoint algorithmic differentiation that enables a very efficient evaluation of energy derivatives, comprising the ionic forces. Thus, one can perform structural optimizations and molecular dynamics in the canonical NVT ensemble at the VMC level. For the electronic part, a full WF optimization (Jastrow and antisymmetric parts together) is made possible, thanks to state-of-the-art stochastic algorithms for energy minimization. In the optimization procedure, the first guess can be obtained at the mean-field level by a built-in DFT driver. The code was efficiently parallelized by using a hybrid MPI-OpenMP protocol, which is also an ideal environment for exploiting the computational power of modern Graphics Processing Unit accelerators.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Baseline Postirradiation Examination of the FUTURIX-FTA Experiments

Postirradiation Examination (PIE) results from the baseline examination of the FUTURIX-FTA irradiation experiment are presented in this report. The FUTURIX-FTA irradiation was designed to study the fuel performance of candidate transmutation fuels. The FUTURIX-FTA experiment was conducted in the true fast neutron spectrum conditions of the Phénix sodium fast test reactor in France. FUTURIX-FTA contained several compositions that were also irradiated as part of the AFC-1 test in cadmium filtered positions in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR) that approximate the neutron spectrum of a fast reactor. This experiment was a joint collaboration between the Department of Energy (DOE) in the U.S. and the Commissariat á l'Energie Atomique et aux Energies Alternatives (CEA) in France. A joint agreement between DOE and CEA was established in 2004 to conduct an irradiation experiment of metallic and nitride fuels in the Phénix reactor at CEA. Both the FUTURIX-FTA tests and the AFC-1 tests were conducted for the DOE Advanced Fuels Campaign (AFC) that is part of Fuel Cycle Research & Development (FCRD) program. These programs seek to develop and demonstrate the technologies needed to transmute long-lived transuranic actinide isotopes contained in spent nuclear fuel via fast reactor technology. The long term goal of this work is to reduce the radiotoxicity of future high level waste repositories. Post-irradiation examination of irradiated fuels experiments provides data related to in reactor fuel performance and input into future fuel design choices. The compositions of the FUTURIX-FTA pins were designed to test if minor actinides could be incorporated into the fuel of a fast reactor without significantly changing fuel performance observed for previously well studied fuels. The fuel performance of metallic fuel in fast reactors has been well documented. Likewise the irradiation performance of nitride fuels in fast reactors has also been documented. However the existing database for nitride fuels is much smaller than the database for metal fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Status PIE Report on Legacy EBR-II and FFTF Metallic Fuel Experiments

A long term research focus of the US Department of Energy (DOE) Advanced Fuels Campaign (AFC) is to investigate technologies that can allow for increased actinide utilization in nuclear fuel for fast neutron spectrum reactors. In order to reach these goals, many experimental campaigns have been tested in an approximated fast reactor neutron spectra at the Idaho National Laboratory Advanced Test Reactor (ATR) in order to study the performance of metallic, nitride, ceramic and advance fuel forms. In addition and complementary to ATR testing, systematic characterization of experiments irradiated in true fast reactors are performed in order to assess ATR in qualifying fast reactor fuel. For this purpose, complementary postirradiation examinations (PIE) are performed on several metallic fuel pins previously irradiated in the EBR II. Advanced PIE techniques developed since the initial PIE of EBR II samples in the 1980’s have been applied in new examinations of irradiated samples during past EBR-II operations. The EBR-II metallic fuel pins analyzed in this report are X501 G591, an early minor actinide-bearing metallic fuel alloy; X430-T653, a U-19Pu-10Zr metallic fuel alloy with a larger diameter compared to EBR-II driver fuel, and more prototypic of future commercial fast reactors; X521-G594, a unique experiment to test the feasibility to burn weapon grade Pu without reprocessing; X496 CL47&CL39 from a long-life metallic fuel experiment with the goal to reach very high burnup; and X486-J555 a U-10Zr Mk-IIIA qualification fuel test that will serve as first of a kind “modelling driven PIE.” These legacy pins were evaluated against the historical fuel performance of previously irradiated fuel from literature. Fuel performance was investigated through a suite of PIE techniques including neutron radiography, gamma spectrometry, dimensional inspection, fission gas release measurements, chemical burnup analysis, optical microscopy, and advance microscopy. So far, the PIE campaign revealed fuel performance and characteristics that are generally in line with literature or EBR-II experience. Some exceptions are present, and they are directly discussed in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Benchmark Study on Innovative Fuels for Fast Reactors with fuel performance codes

The Working Party on the Scientific Issues of the Fuel Cycle (WPFC) has been established under the auspices of the Nuclear Energy Agency (NEA) Nuclear Science Committee (NSC), to co-ordinate scientific activities regarding various existing and advanced nuclear fuel cycles, including advanced reactor systems, associated chemistry and flowsheets, development and performance of fuels and materials, accelerators and spallation targets. Various expert groups were established to cover the above-mentioned topics. Within the WPFC, the Expert Group on Innovative Fuels (EGIF) was created with the objective of conducting joint and comparative studies to support the development of innovative fuels such as homogeneous and heterogeneous fuels, ADS fuels, and oxide, metal, nitride and carbide fuels, all of which can be implemented in advanced nuclear fuel cycles with fast reactors. The scope of the expert group covers innovative fuel fabrication techniques, irradiation performance of innovative fuels, characterisation and post-irradiation examination methods and predictive codes for innovative fuel fabrication and performance. This report presents the results of a benchmark study on innovative fuels for fast reactors using fuel performance codes. Irradiation results were shared among participants, and code calculations were performed to gain further insights on the fuel behaviour. Each participating institution used its own fuel performance code. Code to code and code to experiment comparisons are expected to provide data and improve understanding on the effects of minor actinides on fuel behaviour. In conclusion, the need for improvement of codes will be evaluated and the needs for new experimental data will be identified in order to finalise the code validation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Status Report on Advanced Reactor Fuels Hot Cell Furnace Testing

The Advanced Fuels Campaign is developing a series of out-of-pile steady state furnace tests on irradiated nuclear fuel pins in order to better characterize and understand isolated fuel performance phenomena. These tests will also provide valuable datasets for validation and improvement of modelling and simulation tools. The Blister Anneal Furnace (BAF) in the INL Hot Fuel Examination Facility (HFEF) has been identified as the ideal location for these tests, and, in order to perform them, a new fixture for the BAF has been designed and commissioned. This report summarizes the objectives, design, characteristics and status of this fixture. The design was finalized, materials procured and tested, and the assembly fixture is now fully fabricated in the mock-up shop of the Fuel Conditioning Facility (FCF) at MFC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation Examination of FUTURIX-FTA metallic alloy experiments

Two different metallic nuclear fuel alloys intended for transmutation applications in fast neutron spectrum nuclear reactors have been irradiated, and their performance has been evaluated after irradiation. These alloys contained elevated levels of plutonium and other minor actinides (Am, Np) compared to historically irradiated fast reactor fuel to ascertain the impact of these isotopes on fuel performance. The irradiation of these alloys was performed at the Phénix fast reactor in France to facilitate comparisons between true fast spectrum irradiations and pseudo-fast spectrum irradiations performed at the thermal neutron spectrum Idaho National Laboratory Advanced Test Reactor. The irradiation tests were designated FUTURIX-FTA DOE1 which contained a low-fertile alloy and FUTURIX-FTA DOE2 which contained a non-fertile alloy. The DOE1 fuel was irradiated to a measured burnup of 9.5 % fissions per initial heavy metal atom (FIMA), and the DOE2 fuel was irradiated to a measured burnup of 12.7 % fissions per initial heavy metal atom. This work reports baseline Postirradiation Examination (PIE) results for DOE1 and DOE2. Fuel swelling, fission product distribution, cladding strain, fission gas release, fuel microstructure, fuel cladding chemical interaction and minor actinide transmutation were all evaluated. Cladding strain was negligible and fission gas release was 52% for DOE1 and 69% for DOE2. The exams show the 2 pins behaved very similar to EBR-II metallic fuel experience. Minor actinides seem to not affect the performance of this candidate transmutation fuel. As a result, performance data from these irradiations can be used to inform the feasibility of minor actinide transmutation in future reactor systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation examination of recently irradiated metallic fuel concepts

In fast neutron spectrum nuclear reactors, metallic uranium alloys have often been chosen because of their high uranium density, high thermal conductivity, and several reactor kinetic safety benefits. Metallic uranium is often alloyed to raise the melting temperature or to modify the microstructure which improves irradiation performance. Recent irradiations have explored additional alloys and geometric forms beyond what has historically been irradiated (U-10 weight % Zr, 75% smeared density, sodium bonded fuel). Postirradiation examination results and how these results can be incorporated into modelling and simulation will be presented. The evaluated fuels fall into four categories alternative alloying metals, additives, sodium bond removal, and alternative smear densities. For alternative alloys, Zr has been substituted for 10% Mo or 5% Mo, 4.3%Ti, 0.7%Zr to stabilize the cubic phase of U and prevent constituent redistribution seen in U-Zr alloys. Unfortunately these alloys have significant, undesirable interactions with cladding during irradiation. Additives, such as Pd, have been suggested to bind lanthanide fission products, which interact with cladding limiting fuel performance, into high temperature intermetallic compounds. Irradiation results indicate there may be targeted applications such as high burnup fuel or recycled fuel with lanthanide carry-over where additives are useful. Sodium bonding is considered undesirable at the back end of the fuel cycle where sodium bonded fuel must be treated to remove sodium prior to geological disposition. Helium bonded metallic fuel of several alloys has been irradiated to better understand the implications of removing sodium bonding. Current results show that with proper dimensional tolerances on the final fuel slug, helium bonding is feasible. Low smear density fuel is necessary to enable high (30 atom %) burnup. Both solid and annular low smear density fuels have also been examined, and their performance is also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation Examination of the ATF-1 Experiments - 2018 Status

The Advanced Fuels Campaign in collaboration with industry are working to develop enhanced accident tolerant fuels for light water reactors. The initial irradiations of these concepts were performed in the Idaho National Laboratory Advanced Test Reactor using simple drop-in style irradiations. These irradiations are collectively referred to as ATF 1. The postirradiation examination of ATF 1 has begun and some concepts have now completed initial examination. This report describes the results of examinations on ATF 1 irradiations designed to test the feasibility of enhancing UO 2 thermal conductivity with additives, ATF 1 irradiations of uranium silicide, and the current status of ATF 1 irradiations that are in process at the hot cell. Enhanced thermal conductivity uranium dioxide composites containing silicon carbide (UO 2 SiC) and diamond (UO 2 diamond) have been irradiated to low burnup. The conditions of this irradiation test and subsequent postirradiation examinations are discussed. These irradiations evaluate fuel microstructure and potential fuel cladding interaction under representative light water reactor power conditions. Both non destructive and destructive techniques have been used to evaluate fuel integrity, fission gas release, fission product distribution, burnup, fuel swelling and cladding strain. Examination of the UO 2 SiC pellets revealed enhanced cracking when compared to a UO 2 rodlet also irradiated under similar conditions. Additionally, instability of the SiC whiskers in the uranium dioxide matrix was observed in the pellet central region, where the local temperatures exceeded 1300 °C. The microstructure of the diamond added UO 2 was severely disrupted during irradiation, resulting in local migration of cesium along the fuel stack and increased fission gas release when compared with the expected release from the Vitanza curve at corresponding values of burnup and irradiation temperature. The postirradiation examination results cast doubt on the suitability of these additives to improve UO 2 fuel performance in a way that would lead to enhanced accident tolerance. Additionally, postirradiation examination data of U 3 Si 2 fuels at low burnup (i.e., < 20 GWd/tHM) for application in advanced Light Water Reactor (LWR) is presented. The U 3 Si 2 pellets show limited cracking in comparison to the expected behavior of UO 2 at same power level. In addition, gamma scanning data did not reveal migration of fission products. Minor homogeneous hardening along the pellet radius due to accumulation of fission products and radiation damage was measured by microindentation. The fission gas release and swelling remains very low. Formation of fission gas bubbles resolvable with optical microscopy occurs from the pellets center outward to approximately 60% of the fuel pellet radius. The overall data suggest a good performance of this accident tolerant fuel candidate at low burnup. Finally, the current status of postirradiation examination on other ATF 1 irradiations will be discussed. These irradiations include UO 2 clad in an FeCrAl alloy, an alternative uranium silicide compound U 3 Si 5 also clad in a FeCrAl alloy, and an interaction test between UO 2 and different FeCrAl alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Baseline Postirradiation Examination of the AFC-3C, AFC-3D, and AFC-4A Experiments

A long term research focus of the US Department of Energy (DOE) Advanced Fuels Campaign (AFC) is to investigate technologies that can allow for increased actinide utilization in nuclear fuel for fast neutron spectrum reactors. This includes both the incorporation of minor actinides into nuclear fuel for transmutation and high utilization of actinides through “ultra high” burnup fuel. This goal is defined as fuel that can reach a burnup of 30-40 percent fission per initial metal atom (%FIMA) which is higher than what has historically been achieved [1],[2]. Historically, Experimental Breeder Reactor II (EBR-II) Mark III/IIIA/IV driver fuel (U 10Zr fuel with stainless steel 316 or ferritic martensitic steel HT-9 cladding) was qualified to 10%FIMA, but many experimental assemblies and fuel pins achieved higher peak burnup up to near 20%FIMA without failure [3]. The motivation of the irradiation tests explored in this work was to screen candidate alloys and forms that could tolerate very high burnup irradiations of up to 30 % FIMA. In these irradiations, termed AFC 3C, AFC-3D and AFC-4A, uranium-based alloys and forms were irradiated in a prototypic fast reactor spectrum to investigate fuel performance. Irradiations were performed in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR). The performance of these fuels is compared to the historic performance of U-10Zr [4]. Metallic fuel for fast reactors has a long history that has been reviewed several time in the literature [3]–[8].

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation examination on metallic fuel in the AFC-2 irradiation test series

In this paper, irradiation experiments on metallic fuel alloys containing rare earth additions to simulate potential carry-over from pyro-metallurgical reprocessing and minor actinide additions were performed in the Idaho National Laboratory Advanced Test Reactor. These tests were designated AFC-2A and AFC-2B. Additionally irradiation experiments were also performed on metallic fuel alloys containing minor actinide additions that were fabricated by different techniques. These tests were designated AFC-2E. These pins were removed from the reactor after achieving burnups between 6 and 11% fission per initial heave metal atom. Examination of these pins revealed that they were unintentionally operated beyond their desired power and temperature conditions. Highlights from the postirradiation examination of these experiments is discussed. A variety of issue contributed to the poor performance of these irradiation tests including capsule design, reactor power variations and fabrication issues. While all the issues contributed, the major issue was determined to be unanticipated variations in reactor power. Through comparisons between these experiments and historical off-normal experiments, it was possible to conclude bound the operating temperatures of these experiments. There likely was some in-pile melting in the rare earth addition experiments (AFC-2A, AFC-2B), but it is not likely that there was in-pile melting in the fabrication technique experiments (AFC-2E).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation examination results of several metallic fuel alloys and forms from low burnup AFC irradiations

Several different U based metallic nuclear fuel alloys and forms were irradiated as part of the Advanced Fuels Campaign (AFC) series of irradiation experiments. Results from postirradiation examinations of the AFC-3A and AFC-3B are presented here. In this irradiation, U alloyed with Mo, Zr, and Zr with Pd were investigated. Different geometric forms (solid, annular), smear densities and bonding media (sodium, helium) were also irradiated and evaluated. All fuel forms were irradiated in ferritic-martensitic HT-9 cladding. Examination of the irradiated fuel included neutron radiography, evaluation of the distribution of gamma-ray emitting radionuclides, dimensional inspection, fission gas release analysis, optical microscopy, and chemical analysis. No in-pile failure was observed with this fuel. Neutron radiography, gamma spectrometry, and dimensional inspections indicated the fuel largely performed acceptably. Optical microscopy revealed significant fuel-cladding interaction between the Mo based alloys and the cladding. The Zr based alloys generally performed better although some forms revealed behaviors that present specific fabrication challenges such as tighter fabrication tolerances that will need to be better controlled to match historical U-Zr fuel performance. Furthermore, the addition of Pd as an additive to prevent fuel cladding chemical interaction (FCCI) also appears to present some challenges to fuel performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Testing Fast Reactor Fuels in a Thermal Reactor: A Comparison Report

The testing of fast reactor fuels in the thermal-spectrum of the Advanced Test Reactor using cadmium-filtering has been underway since 2003. The objective of this experimental approach to create a temperature profile inside of test fuel rodlets that is nearly prototypic of corresponding fast reactor conditions. This requires, necessarily, that the power generation profile inside of test fuel rodlets also be nearly prototypic of corresponding fast reactor conditions. By doing so, this experimental approach should allow for the study of fast reactor fuel performance phenomena that are primarily dependent upon the conditions of temperature and/or temperature gradient inside the fuel to be possible using a thermal test reactor. Validation of this assertion has been undertaken by both supporting analyses and by comparing fuel performance phenomena observed in fuels irradiated in cadmium-filtered positions in ATR to similar or identical fuels irradiated under similar conditions in genuine fast reactors. This report documents a preliminary comparison of fuel performance data available from the testing of metallic, oxide, and nitride fuels in cadmium-filtered positions in the ATR to the performance of identical or similar fuels irradiated in genuine fast reactors. Although a variety of fuel performance metrics are presented, particular attention is paid to those phenomena that are primarily, or significantly, dependent on conditions of temperature and temperature gradient with the fuel. Although the comparisons presented in this report are at this time limited in scope and preliminary in nature, they do support the assertion that the objectives of the cadmium-filtered testing approach in ATR are both feasible and appear sound. The analyses and comparisons presented in this report show that ATR irradiations performed using cadmium shrouding are sufficiently prototypic that they can be used with confidence in the development and testing of fast reactor fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗