Engineering Papers⌕ Search

Engineering topics

Cappia, Fabiola

Publications and source records attributed to Cappia, Fabiola.

50 records · Page 3

Post-irradiation examinations of annular mixed oxide fuels with average burnup 4 and 5% FIMA

In this paper, we present post-irradiation examination results on two type of annular mixed oxide fuel pins irradiated in the Fast Flux Test Facility (FFTF) sodium cooled reactor to an average burnup between 4% and 5% fission of initial heavy atom (FIMA). The pins differed only from the initial Pu content, which was 22 wt% and 26 wt%, respectively. The overall performance of the pins was excellent, in line with previous historical results. The pins with higher Pu content experienced higher irradiation temperatures which influenced the fission gas release, fuel swelling, and Cs distribution compared to the other pins. All the post-irradiation examinations results are discussed against the irradiation parameters. In particular, the pins with higher initial Pu content, i.e., 26 wt%, experienced higher power that resulted in enhanced fission gas release compared to the other two pins with 22 wt% initial Pu content. For the pins with higher fission gas release, onset of Cs redistribution was observed. The two pins that had lower initial Pu content and burnup showed a Cs axial distribution similar to the as-produced one.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation Examinations of Accident Tolerant Fuel Candidates with Iron-alloy Cladding

A collaborative effort of the Advanced Fuels Campaign together with industry consortia is focused on the development of enhanced Accident Tolerant Fuels (ATF) for Light Water Reactors (LWRs). The scoping studies, referred to as ATF 1 irradiations, are being performed in the Advanced Test Reactor of Idaho National Laboratory using drop-in style irradiations. The Post Irradiation Examinations (PIEs) of ATF-1 began in 2017 and continued in 2019. This report describes the results of examinations on ATF-1 irradiations designed to test the performance of iron-based cladding. Two rodlets with commercial iron-based cladding and UO2 pellets have been irradiated to low burnup (i.e., < 20 GWd/tHM). The first rodlet had an Alloy33® cladding, while the other had a Kanthal APMT® cladding. The performed PIEs were focused on the determination of fuel microstructure, evaluation of fuel cladding interaction and irradiation-induced variations of cladding mechanical properties. For both rodlets, no significant changes in the cladding hardness were measured, and the cladding hoop strain remained limited. Gamma tomography revealed no Cs axial migration as expected for LWR fuel, but significant cesium radial migration, which was induced by thermal migration consequent to high irradiation temperatures compared to standard LWR irradiation temperatures. Microstructure analyses revealed formation of secondary phases along the pellet rim of samples from both rodlets. No wastage or extensive chemical interaction between the fuel and the internal wall of the cladding was observed, suggesting that the secondary phases accumulated at the pellet rim might be due to formation of Cs-U-O compounds. However, further advanced PIEs are necessary to confirm this hypothesis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-Irradiation Examination (PIE) of Westinghouse-led ATF Concepts U3Si2 and U3Si2-UN. Rodlet Non-Destructive Examinations and Sectioning Diagram.

This report contains the results of non-destructive examinations of three ATF-1 rodlets, namely W01, WB2 and WB6. The rodlets are part of the series of irradiation tests led by Westinghouse within the Accident Tolerant Fuel (ATF) Phase 1 campaign. This report is intended to summarize the performed non-destructive examinations gathered so far on these rodlets and to propose a sectioning diagram before proceeding with destructive examinations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation Examination of the ATF-1 Experiments - 2019 Status

A collaborative effort of the Advanced Fuels Campaign together with industry consortia is focused on the development of enhanced accident tolerant fuels for Light Water Reactors (LWRs). The scoping studies, referred to as ATF-1 irradiations, are being performed in the Advanced Test Reactor of Idaho National Laboratory using drop-in style irradiations. The Post-Irradiation Examinations (PIEs) of ATF-1 began in 2017 and continued in 2019. This report describes the results of examinations on ATF-1 irradiations designed to test the performance of advanced iron-based cladding, including compatibility of FeCrAl with UO2, and ATF-1 irradiation of U3Si5. Two rodlets with commercial iron-based cladding and UO2 pellets have been irradiated to low burnup (i.e., < 20 GWd/tHM). The first rodlet had an Alloy33 cladding, while the other had a Kanthal APMT® cladding. The performed PIEs were focused on the determination of fuel microstructure, evaluation of fuel-cladding interaction and irradiation-induced variations of cladding mechanical properties. For both rodlets, no significant changes in the cladding hardness were measured, and the cladding hoop strain remained limited. Gamma tomography revealed no Cs axial migration as expected for LWR fuel, but significant cesium radial migration, which was induced by thermal migration consequent to high irradiation temperatures. Microstructure analyses revealed formation of secondary phases along the pellet rim of samples from both rodlets. No wastage or extensive chemical interaction between the fuel and the internal wall of the cladding was observed, suggesting that the secondary phases accumulated at the pellet rim might be due to formation of Cs-U-O compounds. However, further advanced PIEs are necessary to finally confirm this hypothesis. Optical microscopy analysis of the rodlet designed by Oak Ridge National Laboratory to evaluate the interaction between UO2 and various FeCrAl alloys revealed no extensive interaction in all the samples irradiated in the rodlet. Localized defects, namely circular pitting and cracks of a few tents of microns, were observed on the FeCrAl disc surfaces in some of the diffusion couples. These defects might be surface fabrication defects rather than irradiation-induced localized corrosion, but chemical analyses are needed to determine whether accumulation of corrosive fission products are causing enhanced interaction. Both non-destructive and destructive PIEs were collected on a rodlet containing U3Si5 fuel. The rodlet had extremely low fission gas release, similar to previously analyzed U3Si2 rodlets. Gamma tomography revealed thermo-migration of fission product ruthenium toward the center of the fuel pellet. The fuel microstructure resembles the as-fabricated microstructure, showing extensive microcracking related to the phase transition at 450°C. Two types of secondary phases were observed, which could either be due to segregation and precipitation of fission products or to UN impurities from fabrication. Finally, the current status of PIE on other ATF-1 irradiations will be discussed. These irradiations include UN-U3Si5 rodlets, UN-U3Si2 rodlets and an additional test with U3Si2 fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Separate Effects Testing in TREAT for ATF Fuels

This work performed examinations on high burnup UO2 from commercial power plant with the intention of better understanding fission gas and fragmentation behavior. Fuel fragmentation, relocation, and dispersal (FFRD) is a major factor in fuel lifetime limits imposed on UO2 by regulators, both domestic and foreign, and is a major area of interest by industry groups (e.g., Electric Power Research Institute, [EPRI]). The characterization of the fuel focused on the differences in porosity between the high burnup (rim) zone, the dark (intermediate) zone, and center zones of the fuel as well as the fission gas content of each region. Work involved thermal treatments to analyze fission gas and high resolution microscopy techniques to investigate pore structure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation examinations of low burnup U 3 Si 2 fuel for light water reactor applications

The United States Department of Energy Advanced Fuels Campaign in collaboration with industry is working to develop enhanced accident tolerant fuels for light water reactors. The initial irradiations of these concepts were performed in the Idaho National Laboratory Advanced Test Reactor using drop-in style irradiations. These irradiations are collectively referred to as Accident Tolerant Fuels 1 (ATF-1). The postirradiation examination of ATF-1 has begun and some concepts have now completed initial examination. This work is focused on postirradiation examination data of U 3 Si 2 fuels at low burnup (i.e., < 20 GWd/tHM) for application in Light Water Reactors (LWRs). The U 3 Si 2 pellets show limited cracking in comparison to the expected behavior of UO 2 at same power level. Moreover, gamma spectrometry data did not reveal migration of fission products. Minor homogeneous hardening along the pellet radius due to accumulation of fission products and radiation damage was measured by microindentation. The fission gas release and swelling remain very low. Formation of fission gas bubbles resolvable with optical microscopy occurs from the pellets center outward to approximately 60% of the fuel pellet radius. With this being said, the overall data suggest a good performance of this accident tolerant fuel candidate at low burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation examinations of UO 2 composites as part of the Accident Tolerant Fuels Campaign

Enhanced thermal conductivity uranium dioxide composites containing silicon carbide (UO 2 -SiC) and diamond (UO 2 -diamond) have been irradiated to low burnup. The conditions of this irradiation test and subsequent postirradiation examinations are discussed. These irradiations evaluate fuel microstructure and potential fuel cladding interaction under representative light water reactor power conditions. Both non-destructive and destructive techniques have been used to evaluate fuel integrity, fission gas release, fission product distribution, burnup, fuel swelling and cladding strain. Examination of the UO 2 -SiC pellets revealed enhanced cracking when compared to a UO 2 rodlet also irradiated under similar conditions. Additionally instability of the SiC whiskers in the uranium dioxide matrix was observed in the pellet central region, where the local temperatures exceeded 1300°C. The microstructure of the diamond-added UO 2 was severely disrupted during irradiation, resulting in local migration of cesium along the fuel stack and increased fission gas release when compared with the expected release from the Vitanza curve at corresponding values of burnup and irradiation temperature. The postirradiation examination results cast doubt on the suitability of these additives to improve UO 2 fuel performance in a way that would lead to enhanced accident tolerance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In-situ small-scale mechanical testing of fast reactor mixed oxide pins: completion report

The present work represents a pioneering study in the application of advanced techniques to measure micro-mechanical properties of highly radioactive advanced nuclear fuels. First data of Young’s modulus and hardness of fast reactor MOX at burnup exceeding 150 GWd/tHM have been obtained. Despite the challenges encountered in the current work due to equipment malfunction, the experimental approach sought in this work has been proved successful in obtaining new data of high relevance for fuel performance on system with high Pu content and high radiotoxicity with extremely limited exposure to personnel. Further experiments will be conducted in the future based on the present approach, leveraging the experience gained in this project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation examination of recently irradiated metallic fuel concepts

In fast neutron spectrum nuclear reactors, metallic uranium alloys have often been chosen because of their high uranium density, high thermal conductivity, and several reactor kinetic safety benefits. Metallic uranium is often alloyed to raise the melting temperature or to modify the microstructure which improves irradiation performance. Recent irradiations have explored additional alloys and geometric forms beyond what has historically been irradiated (U-10 weight % Zr, 75% smeared density, sodium bonded fuel). Postirradiation examination results and how these results can be incorporated into modelling and simulation will be presented. The evaluated fuels fall into four categories alternative alloying metals, additives, sodium bond removal, and alternative smear densities. For alternative alloys, Zr has been substituted for 10% Mo or 5% Mo, 4.3%Ti, 0.7%Zr to stabilize the cubic phase of U and prevent constituent redistribution seen in U-Zr alloys. Unfortunately these alloys have significant, undesirable interactions with cladding during irradiation. Additives, such as Pd, have been suggested to bind lanthanide fission products, which interact with cladding limiting fuel performance, into high temperature intermetallic compounds. Irradiation results indicate there may be targeted applications such as high burnup fuel or recycled fuel with lanthanide carry-over where additives are useful. Sodium bonding is considered undesirable at the back end of the fuel cycle where sodium bonded fuel must be treated to remove sodium prior to geological disposition. Helium bonded metallic fuel of several alloys has been irradiated to better understand the implications of removing sodium bonding. Current results show that with proper dimensional tolerances on the final fuel slug, helium bonding is feasible. Low smear density fuel is necessary to enable high (30 atom %) burnup. Both solid and annular low smear density fuels have also been examined, and their performance is also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Postirradiation Examination of the ATF-1 Experiments - 2018 Status

The Advanced Fuels Campaign in collaboration with industry are working to develop enhanced accident tolerant fuels for light water reactors. The initial irradiations of these concepts were performed in the Idaho National Laboratory Advanced Test Reactor using simple drop-in style irradiations. These irradiations are collectively referred to as ATF 1. The postirradiation examination of ATF 1 has begun and some concepts have now completed initial examination. This report describes the results of examinations on ATF 1 irradiations designed to test the feasibility of enhancing UO 2 thermal conductivity with additives, ATF 1 irradiations of uranium silicide, and the current status of ATF 1 irradiations that are in process at the hot cell. Enhanced thermal conductivity uranium dioxide composites containing silicon carbide (UO 2 SiC) and diamond (UO 2 diamond) have been irradiated to low burnup. The conditions of this irradiation test and subsequent postirradiation examinations are discussed. These irradiations evaluate fuel microstructure and potential fuel cladding interaction under representative light water reactor power conditions. Both non destructive and destructive techniques have been used to evaluate fuel integrity, fission gas release, fission product distribution, burnup, fuel swelling and cladding strain. Examination of the UO 2 SiC pellets revealed enhanced cracking when compared to a UO 2 rodlet also irradiated under similar conditions. Additionally, instability of the SiC whiskers in the uranium dioxide matrix was observed in the pellet central region, where the local temperatures exceeded 1300 °C. The microstructure of the diamond added UO 2 was severely disrupted during irradiation, resulting in local migration of cesium along the fuel stack and increased fission gas release when compared with the expected release from the Vitanza curve at corresponding values of burnup and irradiation temperature. The postirradiation examination results cast doubt on the suitability of these additives to improve UO 2 fuel performance in a way that would lead to enhanced accident tolerance. Additionally, postirradiation examination data of U 3 Si 2 fuels at low burnup (i.e., < 20 GWd/tHM) for application in advanced Light Water Reactor (LWR) is presented. The U 3 Si 2 pellets show limited cracking in comparison to the expected behavior of UO 2 at same power level. In addition, gamma scanning data did not reveal migration of fission products. Minor homogeneous hardening along the pellet radius due to accumulation of fission products and radiation damage was measured by microindentation. The fission gas release and swelling remains very low. Formation of fission gas bubbles resolvable with optical microscopy occurs from the pellets center outward to approximately 60% of the fuel pellet radius. The overall data suggest a good performance of this accident tolerant fuel candidate at low burnup. Finally, the current status of postirradiation examination on other ATF 1 irradiations will be discussed. These irradiations include UO 2 clad in an FeCrAl alloy, an alternative uranium silicide compound U 3 Si 5 also clad in a FeCrAl alloy, and an interaction test between UO 2 and different FeCrAl alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Baseline Postirradiation Examination of the AFC-3C, AFC-3D, and AFC-4A Experiments

A long term research focus of the US Department of Energy (DOE) Advanced Fuels Campaign (AFC) is to investigate technologies that can allow for increased actinide utilization in nuclear fuel for fast neutron spectrum reactors. This includes both the incorporation of minor actinides into nuclear fuel for transmutation and high utilization of actinides through “ultra high” burnup fuel. This goal is defined as fuel that can reach a burnup of 30-40 percent fission per initial metal atom (%FIMA) which is higher than what has historically been achieved [1],[2]. Historically, Experimental Breeder Reactor II (EBR-II) Mark III/IIIA/IV driver fuel (U 10Zr fuel with stainless steel 316 or ferritic martensitic steel HT-9 cladding) was qualified to 10%FIMA, but many experimental assemblies and fuel pins achieved higher peak burnup up to near 20%FIMA without failure [3]. The motivation of the irradiation tests explored in this work was to screen candidate alloys and forms that could tolerate very high burnup irradiations of up to 30 % FIMA. In these irradiations, termed AFC 3C, AFC-3D and AFC-4A, uranium-based alloys and forms were irradiated in a prototypic fast reactor spectrum to investigate fuel performance. Irradiations were performed in the Idaho National Laboratory (INL) Advanced Test Reactor (ATR). The performance of these fuels is compared to the historic performance of U-10Zr [4]. Metallic fuel for fast reactors has a long history that has been reviewed several time in the literature [3]–[8].

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Grain Size and Phase Purity Characterization of U 3 Si 2 Pellet Fuel

Characterization of U 3 Si 2 fresh fuel pellets is important for quality assurance and validation of the finished product. Grain size measurement methods, phase identification methods using scanning electron microscopes equipped with energy dispersive spectroscopy and x-ray diffraction, and phase quantification methods via image analysis have been developed and implemented on U 3 Si 2 pellet samples. A wide variety of samples have been characterized including representative pellets from an initial irradiation experiment, and samples produced using optimized methods to enhance phase purity from an extended fabrication effort. The average grain size for initial pellets was between 16 and 18 µm. The typical average grain size for pellets from the extended fabrication was between 20 and 30 µm with some samples exhibiting irregular grain growth. Pellets from the latter half of extended fabrication had a bimodal grain size distribution consisting of coarsened grains (>80 µm) surrounded by the typical (20-30 µm) grain structure around the surface. Phases identified in initial uranium silicide pellets included: U 3 Si 2 as the main phase composing about 80 vol. %, Si rich phases (USi and U 5 Si 4 ) composing about 13 vol. %, and UO 2 composing about 5 vol. %. Initial batches from the extended U 3 Si 2 pellet fabrication had similar phases and phase quantities. The latter half of the extended fabrication pellet batches did not contain Si rich phases, and had between 1-5% UO 2 : achieving U 3 Si 2 phase purity between 95 vol. % and 98 vol. % U 3 Si 2 . The amount of UO 2 in sintered U 3 Si 2 pellets is correlated to the length of time between U 3 Si 2 powder fabrication and pellet formation. These measurements provide information necessary to optimize fabrication efforts and a baseline for future work on this fuel compound.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗