Integrated multiscale experiment and model analysis of radially resolved microstructure and thermal conductivity in mixed oxide fuel
Not Available
Fuel performance modeling↗
Engineering topics
Cappia, Fabiola
Publications and source records attributed to Cappia, Fabiola.
Design and Evaluation of a Ring Tension Test Grip for Remote Mechanical Testing of Irradiated Tubular Specimens
Here, the ring tension test (RTT) is a mechanical testing method for determining bulk mechanical behavior in the circumferential or hoop direction for tubular materials. The test is especially useful for testing materials with anisotropic mechanical properties, such as zirconium alloys, which are commonly used as nuclear fuel cladding. Anisotropy requires direction-specific testing to determine the hoop strength. Historically, several RTT methods and grips have been used, each method has its strengths and weaknesses, and, in all cases, the measured strength is subject to uncertainty due to variations of the testing geometry and experimental tolerances. Recent analysis has shown that grips with a hemicylindrical mandrel configuration are recommended as the most robust configuration. The two strictest aspects to be controlled are the ability to determine gage region orientation and closely matching the size of the mandrels to the test specimen. This last requirement is particularly challenging when the dimensions of the specimen vary because of environmental effects such as dimensional changes due to irradiation. This paper presents a new RTT grip designed to incorporate this mandrel shape, hold the gage at the desired orientation, be suitable for remote operation in a hot-cell environment, and be adaptable for different sizes or variations in the specimen size. The general description and the unique design features of the test specimen and grips are given in detail. The performance of the grips in mechanical testing, including in a remote hot-cell environment, is also provided.
42 ENGINEERING↗
Length scale effects of micro- and meso-scale tensile tests of unirradiated and irradiated Zircaloy-4 cladding
Zircaloy-4 is an essential material for cladding structures within fission-based reactors. To explore the changes in properties measured on differing length scales, FIB-machined micro-scale tensile tests were performed on both irradiated and control groups of Zircaloy-4. This was correlated with tensile testing on femtosecond laser-machined meso-scale specimens. Pronounced size effects were found when varying specimen geometry. Increases in tensile geometry size were associated with a reduction in measured yield stress for both irradiated and unirradiated samples. Here, meso-scale testing found strength and strain values similar to that of bulk-scale testing.
36 MATERIALS SCIENCE↗
FUEL PERFORMANCE STUDIES AT IDAHO NATIONAL LABORATORY MAKING USE OF THE BYRON FUEL SHIPMENT
In December of 2023 a shipment of commercially irradiated fuel rods from the Byron Generating Station in Illinois was successfully shipped to the Materials and Fuels Complex (MFC) at Idaho National Laboratory (INL). The make-up of the rods includes a mix of cladding types from traditional ZirloTM, advanced zirconium alloys, and chrome coated ZirloTM. Burnups range from regular end of life values to over 70 GWd/MTU rod average. The R&D plan for the rods involves multiple projects from developing licensing data for new claddings to integral transient tests to support burnup extension efforts in the United States. The R&D began in early 2024 with the nondestructive examinations of the rods after which they will be sectioned for microscopy, mechanical testing, and analytical chemistry. Additionally, many rod segments will be refabricated into new test pins and inserted into a static water capsule for integral Reactivity Initiated Accident (RIA) and Loss of Coolant Accident (LOCA) testing at the TREAT reactor.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
THE U.S. ACCIDENT TOLERANT FUELS PROGRAM: RECENT ACCOMPLISHMENTS SUPPORTING IMPLEMENTATION
Explore the source record for details and available documents.
Capps, Nathan↗
Status Report on Characterization of High Burnup Fuel with Advanced Nondestructive Pulsed Neutron PIE
Characterizing irradiated or spent nuclear fuels with pulsed neutron techniques provides microstructural data such as phase fractions as well as crystallographic data, e.g. lattice parameters, from diffraction analysis. Diffraction characterization is complemented by spatially resolved mapping of isotope densities from energy-resolved neutron imaging, in particular neutron absorption resonance imaging, and overall bulk isotope assay with better sensitivity for minority isotopes from neutron absorption resonance spectroscopy without spatial resolution. Furthermore, after characterization at ambient condition, heating of irradiated or spent fuel will allow to characterize differences of e.g. lattice thermal expansion or phase transition temperature and kinetics compared to fresh fuel as well as enable the study of disappearance of irradiation defects. This data enables benchmarking of predictions of properties of irradiated fuels for which otherwise experimental data is sparse. The effort described here strives to characterize a section cut from a high-burnup fuel. Volumes smaller than entire fuel pellets or rodlets as proposed here, e.g. sections cut from a fuel pellet, to pave the way to characterize entire pellets or rodlets in the future.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Enabling Digital Image Correlation for Deployment in the Hot Fuels Examination Facility
Digital image correlation (DIC) is a non-contact image-based technique for displacement and strain measurement. It is also a full-field method that can provide excellent spatial resolution. DIC has been widely used for measurements in many styles of mechanical tests and is desirable in part because of this flexibility to measure nearly any material across a range of time and length scales. Its ability to measure localized strain for tests and in environments not accessible to other strain measurement techniques makes it an ideal option for several mechanical test cases that exist in hot cell facilities such as the Hot Fuel Examination Facility (HFEF) at the Idaho National Laboratory (INL). However, DIC has not been demonstrated at HFEF, and several barriers to implementation in the hot cell environment exist. This report outlines the possible paths for deploying DIC at HFEF, weighing the technical advantages and risks with each path. It also discusses the steps which must be taken to add this capability to the suite of post-irradiation examination (PIE) techniques available at HFEF. Finally, it concludes with recommendations for the best method to perform DIC at the facility.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Integrated Approach to Post-Irradiation Examination of Nuclear Materials at Idaho National Laboratory
Idaho national Laboratory (INL) is the U.S. lead national laboratory for the Department of Energy’s Office of Nuclear Energy (DOE-NE), providing much of the nuclear research, development and demonstration capability needed to move nuclear innovation forward to deployment. INL’s Materials and Fuels Complex hosts a unique combination of personnel, facilities and infrastructure and offers the ability to perform post-irradiation examinations (PIE) of nuclear materials spanning multiple length scales. The ability to combine engineering-scale analysis and sub-microscopic characterization provides valuable insights into fuel and structural material behavior and degradation mechanisms. The holistic approach is used to accelerate these materials demonstration and deployment. Selected studies will be presented, highlighting the impact of these techniques on improving fuel reliability, safety, and efficiency, thereby advancing the development of sustainable and advanced nuclear energy technologies.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Analysis of radially resolved thermal conductivity in high burnup mixed oxide fuel and comparison to thermal conductivity correlations implemented in fuel performance codes
The thermal diffusivity and thermal conductivity of high burnup (19 % FIMA) mixed oxide (U, Pu)O 2 nuclear fuel has been measured along the radial direction using a thermoreflectance-based method. Measured thermal conductivity exhibits a notable radial variation consistent with the expectations that a large temperature gradient across the annular fuel pellet leads to a heterogeneous microstructure. A common fuel performance model of thermal conductivity, the Lucuta-Inoue model, is used to analyze the measured thermal conductivity profile. Further, this model adequately captures the radial dependence of thermal conductivity except in the periphery. The analysis suggests that the characteristic radial shape of the thermal conductivity profile follows the burnup profile within the fuel pin. In the periphery, the high burnup structure is formed and the conductivity model, not capturing this effect, likely overestimates the thermal conductivity.
36 MATERIALS SCIENCE↗
FeCrAl fuel/clad chemical interaction in light water reactor environments
This article investigates the fuel-cladding chemical interaction (FCCI) behavior of two commercial FeCrAl alloys, APMT composition (Fe-21Cr-5Al-3Mo wt.%) and C35M (Fe-13Cr-5Al-2Mo-0.2Si-0.03Y wt.%), after neutron irradiation. “H-cup” diffusion multiples of FeCrAl alloys and ceramic UO 2 fuel were irradiated at a temperature of ~300 °C to a total estimated burnup of 26 GWd/tHM. Post-irradiation Examination results demonstrate the excellent degradation resistance of FeCrAl alloys as accident tolerant fuel (ATF) cladding materials in light water reactor conditions. The study concludes that there was no irradiation-induced defects observed in either of the two commercial FeCrAl claddings. The formation of amorphous Al/U mixed oxide was observed at the fuel-clad interface, which can serve as a tritium permeation barrier and protect against potential chemical attack from the fuel. Finally, the study attributed the formation of amorphous Al/U mixed oxide to the low temperature and limited time of neutron irradiation. APMT forms more distinct Cr and Cr-Fe intermetallic at the FeCrAl-UO 2 interface than C35M due to the higher bulk Cr:Al ratio.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Evaluation of the ring tension test (RTT) for robust determination of material strengths
The ring tension test (RTT) is an experimental method for determining mechanical behavior in a material’s circumferential or hoop direction. It is a crucial test for testing anisotropic materials with tube geometry, such as nuclear fuel cladding or irradiated pipes. Several RTT configurations exist, each with their own advantages and disadvantages. However, this test is significantly more complex than traditional tensile testing and can be especially sensitive to small differences and inconsistencies in the test setup and geometry, ultimately affecting the derived mechanical properties. Previous research has focused on method development, and little work has been done on understanding the subtle differences between an ideal test and experiments, specifically when the tests are performed on highly irradiated materials in hot cells. In this work, a finite element-based investigation of the RTT is conducted to fill this gap. The two most used test configurations are investigated, comparing their ability to determine accurate material strengths through plastic deformation. Several non-ideal conditions and uncontrollable effects which are likely to occur during experimental testing such as machining tolerances, variations of specimen geometry from nominal dimensions, rotation of specimens and fixturing, and other test setup discrepancies are studied. The sensitivity of measured strengths to these conditions is presented. A mechanics-based approach to describing and correcting raw data to determine actual strengths is also included for one of the configurations, resulting in a robust correction method with highly accurate material strength measurements. Finally, based on these analyses, the hemicylindrical mandrel configuration is recommended with a gauge region oriented at a 45° angle.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Modeling and Measurement of Axial Gas Transport in Nuclear Fuels [Poster]
Axial gas transport plays a crucial role in determining pressure equilibrium in nuclear fuel rods. Permeability is currently determined a posteriori. Current models assume instantaneous pressure equilibrium and laminar flow.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Modeling and Measurement of Axial Gas Transport in Nuclear Fuels
This document is an American Nuclear Society (ANS) transaction for the ANS annual conference. This transaction provides an overview of the Modeling and Measurement of Axial Gas Transport Laboratory Directed Research and Development project including preliminary modeling results. The goal is to provide model for axial gas transport in the Bison Fuel Performance code to support industry's desire to achieve higher burnups in existing light water reactors. A brief overview of the experimental approach and associated modeling activities is presented.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Post-irradiation examination of low burnup U 3 Si 5 and UN-U 3 Si 5 composite fuels
Here this work presents post-irradiation examination data on UN-U 3 Si 5 and U 3 Si 5 fuels at low burnup (i.e., <10–15 GWd/tHM) with Kanthal AF® cladding. The results suggest good irradiation performance for both the silicide and nitride-silicide composite pellets. Optical microscopy revealed that the pellet-cladding gap is still open, and limited axial cracking was observed only in UN-U 3 Si 5 pellets. Microcracking was isolated to the U 3 Si 5 phase in all cases and was observed in pre-irradiation and depleted pellets, indicating that it was not irradiation induced. The fission gas release was minimal for the calculated fission density achieved (2.6 – 3.15 × 10 20 fiss/cm 3 ). No fission gas bubbles were observed in the optical metallography. These results suggest acceptable swelling and fission gas behavior for both the single phase and composite compositions.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
The effects of radiation-induced grain subdivision and dislocations on the fracture properties of uranium dioxide
Microcantilever bending tests were applied on uranium dioxide samples irradiated by 84 MeV Xe ions. Depending on the initial grain sizes, different levels of grain subdivision and dislocation development were observed near the irradiated surface. These radiation damage features were shown to degrade the fracture properties of both samples. The fundamental aspects of the radiation-microstructure-property relationships were discussed in this paper, taking a holistic consideration of the microcantilever bending data, fractography and microstructures. The separate effects of the irradiation-induced grain subdivision and dislocations on the fracture initiation and propagation of uranium dioxide were discussed. In conclusion, it was observed that radiation-induced dislocations and grain subdivision, without the presence of Xe bubbles co-located with the defects, cause reductions in the Young's modulus, fracture strain, and fracture stress, and a transition to intergranular fracture.
36 MATERIALS SCIENCE↗
Consensus DOE Advanced Fuels Campaign TREAT/SATS Test Plan [Slides]
This record is comprised of summary slides of the Combined TREAT-LOC & SATS Integral LOCA Experiment Plan. The experimental program has been developed to specifically address data gaps and opportunities identified through detailed review of the existing public knowledgebase on LOCA FFRD and specific experimental development for prototypic LOCA conditions for LWR systems. The test program relies on a unique combination of in-pile and out-of-pile experimental approaches to (1) provide clear tieback to the existing integral and semi-integral LOCA experiment database using state-of-the-art facilities. More importantly, this program will systematically investigate the impacts of: (2) prototypic HBu fuel and cladding thermomechanical behaviors under postulated LWR LOCA conditions never fully investigated before. These conditions correspond with prototypic decay-energy heat up (DEH) and stored-energy heat up (SEH) conditions. Unique TREAT capability will provide first evaluation of SEH conditions on HBu fuels. The test program includes an emphasis on developing improved mechanistic understanding of key phenomena through independent experimental systems, development of a database to support fuel performance modeling tools, world leading advanced materials characterization, and the most advanced approach to in-situ diagnostics ever deployed to evaluate FFRD. The results will represent a significant leap forward in the evaluation of prototypic conditions and novel data to support modeling development and validation, as well as to inform the technical basis of LOCA-induced FFRD.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗