Engineering Papers⌕ Search

Engineering topics

Cannon, R. H., Jr.

Publications and source records attributed to Cannon, R. H., Jr..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Experiments with simplified computed-torque controllers for free-flying robots

The effect of neglecting base accelerations in an inertial space endpoint computed-torque (CT) controller is examined. Numerical simulations predict a rather wide set of conditions under which CT controllers can neglect base accelerations in their dynamic model with insignificant performance degradation. Two predictions are experimentally verified with a laboratory robot. These two experiments show that negligible additional endpoint controller error results with a simplified CT controller for the given robot mass parameters and manipulator articulation.

Koningstein, R.↗
NASA NTRS1990

Initial experiments in thrusterless locomotion control of a free-flying robot

A two-arm free-flying robot has been constructed to study thrusterless locomotion in space. This is accomplished by pushing off or landing on a large structure in a coordinated two-arm maneuver. A new control method, called system momentum control, allows the robot to follow desired momentum trajectories and thus leap or crawl from one structure to another. The robot floats on an air-cushion, simulating in two dimensions the drag-free zero-g environment of space. The control paradigm has been verified experimentally by commanding the robot to push off a bar with both arms, rotate 180 degrees, and catch itself on another bar.

Jasper, W. J.↗
NASA NTRS1989

Experiments in global navigation and control of a free-flying space robot

This paper reviews initial work at the Stanford University Aerospace Robotics Laboratory (ARL) in developing and controlling a free-flying space robot. The objective of this project is to develop a laboratory version of a space robot that is capable of performing target tracking, acquisition, and manipulation. In particular, this paper focuses on the problems associated with capturing a free-floating object that is initially out of reach of the robot. A set of rules is presented for generating an appropriate intercept trajectory. A controller architecture suitable for carrying out these motions is also described. Finally the results of computer simulations illustrating the behavior of these algorithms are shown along with a description of the physical hardware on which they will be tested.

Ullman, M.↗
NASA NTRS1987

Experiments in advanced control concepts for space robotics - An overview of the Stanford Aerospace Robotics Laboratory

The Stanford University Aerospace Robotics Laboratory is actively developing and experimentally testing advanced robot control strategies for space robotic applications. Early experiments focused on control of very lightweight one-link manipulators and other flexible structures. The results are being extended to position and force control of mini-manipulators attached to flexible manipulators and multilink manipulators with flexible drive trains. Experimental results show that end-point sensing and careful dynamic modeling or adaptive control are key to the success of these control strategies. Free-flying space robot simulators that operate on an air cushion table have been built to test control strategies in which the dynamics of the base of the robot and the payload are important.

Hollars, M. G.↗
NASA NTRS1985

Control of a free-flying robot manipulator system

The goal of the research is to develop and test control strategies for a self-contained, free flying space robot. Such a robot would perform operations in space similar to those currently handled by astronauts during extravehicular activity (EVA). The focus of the work is to develop and carry out a program of research with a series of physical Satellite Robot Simulator Vehicles (SRSV's), two-dimensionally freely mobile laboratory models of autonomous free-flying space robots such as might perform extravehicular functions associated with operation of a space station or repair of orbiting satellites. The development of the SRSV and of some of the controller subsystems are discribed. The two-link arm was fitted to the SRSV base, and researchers explored the open-loop characteristics of the arm and thruster actuators. Work began on building the software foundation necessary for use of the on-board computer, as well as hardware and software for a local vision system for target identification and tracking.

Alexander, H.↗
NASA NTRS1985

Space robot simulator vehicle

A Space Robot Simulator Vehicle (SRSV) was constructed to model a free-flying robot capable of doing construction, manipulation and repair work in space. The SRSV is intended as a test bed for development of dynamic and static control methods for space robots. The vehicle is built around a two-foot-diameter air-cushion vehicle that carries batteries, power supplies, gas tanks, computer, reaction jets and radio equipment. It is fitted with one or two two-link manipulators, which may be of many possible designs, including flexible-link versions. Both the vehicle body and its first arm are nearly complete. Inverse dynamic control of the robot's manipulator has been successfully simulated using equations generated by the dynamic simulation package SDEXACT. In this mode, the position of the manipulator tip is controlled not by fixing the vehicle base through thruster operation, but by controlling the manipulator joint torques to achieve the desired tip motion, while allowing for the free motion of the vehicle base. One of the primary goals is to minimize use of the thrusters in favor of intelligent control of the manipulator. Ways to reduce the computational burden of control are described.

Cannon, R. H., Jr.↗
NASA NTRS1985

Self-Tuning Adaptive-Controller Using Online Frequency Identification

A real time adaptive controller was designed and tested successfully on a fourth order laboratory dynamic system which features very low structural damping and a noncolocated actuator sensor pair. The controller, implemented in a digital minicomputer, consists of a state estimator, a set of state feedback gains, and a frequency locked loop (FLL) for real time parameter identification. The FLL can detect the closed loop natural frequency of the system being controlled, calculate the mismatch between a plant parameter and its counterpart in the state estimator, and correct the estimator parameter in real time. The adaptation algorithm can correct the controller error and stabilize the system for more than 50% variation in the plant natural frequency, compared with a 10% stability margin in frequency variation for a fixed gain controller having the same performance at the nominal plant condition. After it has locked to the correct plant frequency, the adaptive controller works as well as the fixed gain controller does when there is no parameter mismatch. The very rapid convergence of this adaptive system is demonstrated experimentally, and can also be proven with simple root locus methods.

Chiang, W. W.↗
NASA NTRS1985

The experimental results of a self tuning adaptive controller using online frequency identification

A fourth-order laboratory dynamic system featuring very low structural damping and a noncolocated actuator-sensor pair has been used to test a novel real-time adaptive controller, implemented in a minicomputer, which consists of a state estimator, a set of state feedback gains, and a frequency-locked loop for real-time parameter identification. The adaptation algorithm employed can correct controller error and stabilize the system for more than 50 percent variation in the plant's natural frequency, compared with a 10 percent stability margin in frequency variation for a fixed gain controller having the same performance as the nominal plant condition. The very rapid convergence achievable by this adaptive system is demonstrated experimentally, and proven with simple, root-locus methods.

Chiang, W.-W.↗
NASA NTRS1984

Experiments in control of flexible structures with noncolocated sensors and actuators

While the stable control of such flexible structures as limber spacecraft is easily achieved through the colocation of control actuators with sensors, noncolocation renders this extremely difficult. The most difficult case in point is that in which structural damping is low and spacecraft stiffness and inertia values are uncertain and changing. Attention is presently given to an apparatus in which each basic sensor/actuator noncolocation configuration is available, and inertias can be abruptly halved or doubled during control maneuvers. This feature can impose a sudden reversal in the plant's pole-zero sequence, which is a very difficult condition for the controller. Test results obtained to date demonstrate the inherent difficulty of achieving robustness in the case of noncolocation. It is noted that there may be very simple configurations in which there is no alternative to adaptive control.

Cannon, R. H., Jr.↗
NASA NTRS1984

Precise control of flexible manipulators

The design and experimental testing of end point position controllers for a very flexible one link lightweight manipulator are summarized. The latest upgraded version of the experimental set up, and the basic differences between conventional joint angle feedback and end point position feedback are described. A general procedure for application of modern control methods to the problem is outlined. The relationship between weighting parameters and the bandwidth and control stiffness of the resulting end point position closed loop system is shown. It is found that joint rate angle feedback in addition to the primary end point position sensor is essential for adequate disturbance rejection capability of the closed loop system. The use of a low order multivariable compensator design computer code; called Sandy is documented. A solution to the problem of control mode switching between position sensor sets is outlined. The proof of concept for endpoint position feedback for a one link flexible manipulator was demonstrated. The bandwidth obtained with the experimental end point position controller is about twice as fast as the beam's first natural cantilevered frequency, and comes within a factor of four of the absolute physical speed limit imposed by the wave propagation time of the beam.

Cannon, R. H., Jr.↗
NASA NTRS1984

Precise control of flexible manipulators

Experimental apparatus were developed for physically testing control systems for pointing flexible structures, such as limber spacecraft, for the case that control actuators cannot be collocated with sensors. Structural damping ratios are less than 0.003, each basic configuration of sensor/actuator noncollocation is available, and inertias can be halved or doubled abruptly during control maneuvers, thereby imposing, in particular, a sudden reversal in the plant's pole-zero sequence. First experimental results are presented, including stable control with both collocation and noncollocation.

Cannon, R. H., Jr.↗
NASA NTRS1984

Initial experiments on the end-point control of a flexible one-link robot

The present investigation is concerned with initial experiments regarding a specific unsolved control problem which appeared to be central to advances in the art of robotics. This problem involves the control of a flexible member (one link of a robot system). The position of the end-effector, called the end point or tip, is controlled by measuring that position and using the measurement as a basis for applying control torque to the other end of the flexible member, as for instance, the robot's elbow joint. A description is presented of the features of the first experimental arm which has been made, and an outline is provided of the general strategy for controlling it using its tip sensor and shoulder torquer.

Cannon, R. H., Jr.↗
NASA NTRS1971

Static properties of hydrostatic thrust gas bearings with curved surfaces.

The classical treatment of circular, hydrostatic, orifice-regulated thrust gas bearings, in which perfectly plane bearing plates are assumed, is extended to include axisymmetric, but otherwise arbitrary, plate profiles. Plate curvature has a strong influence on bearing load capability, static stiffness, tilting stiffness, and side force per unit misalignment angle. By a suitable combination of gas inlet impedance and concave plate profile, the static stiffness can be made almost constant over a wide load range, and to remain positive at the closure load. Extensive measurements performed with convex and concave plates agree with theory to within the experimental error throughout and demonstrate the practical feasibility of using curved plates.

Rehsteiner, F. H.↗