Engineering topics

Campbell, Keri

Publications and source records attributed to Campbell, Keri.

3 records

DOE OSTI2024

Performance and properties evolution of near-term accident tolerant fuel: Cr-doped UO 2

Chromium-doped UO 2 fuel has received significant interest due to the ability for chromium to produce pellets with large average grain size (>30 μm), which has shown to increase fission gas retention during operation. Sintering of chromium-doped UO 2 pellets was pursued with oxygen potential and sintering atmosphere controlled to tailor the final microstructure of the material. Chromium additions in this study ranged from 750 to 7800 ppm. Cr concentrations were studied pre and post sintering using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Effects of chromium content on lattice parameter and microstructure were examined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Contraction of the UO 2 lattice parameter was observed, as well as enlargement of grain size with increasing chromium content up to 4900 ppm Cr 2 O 3 . In addition, SEM indicated Cr incorporation within the matrix and the formation of chromium oxide precipitates throughout the microstructure at high Cr concentrations. Evaluation of thermophysical properties of Cr-doped UO 2 pellets were conducted up to 1200 °C to illustrate their evolution with increased dopant concentration and microstructural changes. The results show that grain size is maximized at 52 μm with Cr 2 O 3 concentration equal to 4900 ppm; however, grain size decreases at higher Cr 2 O 3 concentrations. No significant changes were observed in specific heat capacity, linear thermal expansion, and coefficient of thermal expansion compared to undoped UO 2 . The thermal conductivity also decreased through the incorporation of Cr 2 O 3 dopants above 750 ppm and is shown to be ~15 % lower than reported UO 2 values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Effects of uranium metal carbon content on hydriding kinetics and corrosion blister number/area at sub-ambient pressures

Carbon is a common impurity in uranium metal, resulting in a number of uranium–carbon inclusion phases that contribute to an increase in metal defect density as carbon content increases. It is widely held that uranium hydride corrosion preferentially nucleates at these defect sites, and that an increase in carbon content will therefore represents an increase in uranium hydride corrosion sites on the metal surface. We hydrided six uranium sources with differing carbon contents to explore whether this assumption holds in a sub-ambient (~ 0.1 atm hydrogen), sealed environment, and report the resulting reaction kinetics and uranium hydride blister benchmarking data. We find that carbon content is not strongly correlated with reaction kinetics terms or the resulting hydride blister number and area, but that there is a tight relationship between corrosion blister number/area and kinetics as is expected. Further, we find that there is a strong trend of decreasing variance in the blister number, blister area, and induction time as carbon content increases (higher carbon content results in more reproducible blister populations). Additionally, we find a narrow band of uranium metal consumption at the end of the parabolic phase of reaction progress (beginning of linear growth phase) of 0.098 ± 0.011 w/w%, a fact that may be useful in assaying hydrogen corrosion of uranium metal within sealed environments generally.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2023

Hydrogen Diffusion Coefficient Measures on Thin Film Uranium Oxide

Thin films of uranium oxides, putatively UO 2 and U 3 O 8 , were deposited on palladium/silver (75/25) foil discs (10 μm thick, 10 mm diameter). Methodology for sealing these foils, applying a hydrogen pressure (~ 1 atm) to the oxide side, and measuring the pressure on the permeate side (opposite side of foil) is reported. The experimental apparatus is held at 100 °C to speed diffusion, aided by the pressure differential across the foil (~1 atm (750 torr) on oxide side, initially low vacuum on permeate side, ~1x 10 -4 torr). Early results indicate an effective diffusion coefficient of roughly 7.66 x 10 -17 +/- 2.22 x 10 -17 cm 2 /sec for UO 2 . These values are in line with expectations and prior measures relative to large lag times for system baseline (substrate only). Evaluation of the technique for U 3 O 8 thin films suggests further development will be needed to extend the technique to more oxidized films (U 3 O 8 , UO 3 ). Characterization of the foils (thickness and speciation) post diffusion experiments will be carried out by SIGMA (Eric Tegtmeier and Andy Richards) in FY24 which will sharpen the uncertainty quantification for UO 2 diffusion coefficients, aiding the nucleation model for DRACO.

36 MATERIALS SCIENCE↗