Engineering Papers⌕ Search

Engineering topics

Campbell, J. F.

Publications and source records attributed to Campbell, J. F..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Flow visualization of leading-edge vortex enhancement by spanwise blowing

Flow visualization studies were conducted in a small pilot wind tunnel to determine qualitative effects of blowing a discrete jet essentially parallel to the leading edge of a 45 deg-swept trapezoidal wing featuring leading- and trailing-edge flaps. Test parameters included wing angle-of-attack, jet momentum coefficient, leading- and trailing-edge flap deflections, and nozzle chordwise displacement. Results of this study indicate that blowing from a reflection plane over the wing enhances the leading-edge vortex and delays vortex bursting to higher angles-of-attack and greater span distances. Increased blowing rates decrease vortex size, growth rate, and vertical displacement above the wing surface at a given span station and also extend the spanwise effectiveness of lateral blowing. Deflection of a leading-edge flap delays the beneficial effects of spanwise blowing to higher angles-of-attack. Nozzle chordwise locations investigated for the wing with and without leading-edge flap deflection appear equally effective in enhancing the separated leading-edge flow.

Erickson, G. E.↗
NASA NTRS1975

Augmentation of vortex lift by spanwise blowing

An investigation has been conducted to evaluate the aerodynamic effects associated with blowing a jet spanwise over a wing's upper surface in a direction parallel to the leading edge. Experimental pressure and force data were obtained on wings with sweep angles of 30 and 45 degrees and showed that spanwise blowing aids in the formation and control of the leading-edge vortex and, hence, significantly improves the aerodynamic characteristics at high angles of attack. Full vortex section lift is achieved at the inboard span station with a small blowing rate, but successively higher blowing rates are necessary to attain the full vortex-lift level at increased span distances. Spanwise blowing generates large increases in lift at high angles of attack, improves the drag polars, and extends the linear pitching moment to high lifts.

Campbell, J. F.↗
NASA NTRS1975

Effects of spanwise blowing on the pressure field and vortex-lift characteristics of a 44 deg swept trapezoidal wing

Wind-tunnel data were obtained at a free-stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and jet location. Results of this study show that the sectional effects to spanwise blowing are strongly dependent on angle of attack, jet thrust coefficient, and span location; the largest effects occur at the highest angles of attack and thrust coefficients and on the inboard portion of the wing. Full vortex lift was achieved at the inboard span station with a small blowing rate, but successively higher blowing rates were necessary to achieve full vortex lift at increased span distances. It is shown that spanwise blowing increases lift throughout the angle-of-attack range, delays wing stall to higher angles of attack, and improves the induced-drag polars. The leading-edge suction analogy can be used to estimate the section and total lifts resulting from spanwise blowing.

Campbell, J. F.↗
NASA NTRS1975

Experimental measurements of skin friction on upper surface blown wing

An experimental investigation was conducted to obtain skin-friction measurements on a wing with a circular jet exhausting above it. A Preston tube was used to determine the local shear stress at a point on the wing's upper surface. Data were obtained for four nozzle pressures and four vertical displacements of the jet above the wing. The results indicated that the highest skin-friction values occurred with the jet closest to the wing and with the highest nozzle pressure. These data trends were validated by calculations which combined two-dimensional, turbulent boundary-layer theory with axisymmetric co-flowing jet theory.

Miner, D. D.↗
NASA NTRS1973

Analysis of the injection of a heated turbulent jet into a cross flow

The development of a theoretical model is investigated of the incompressible jet injection process. The discharge of a turbulent jet into a cross flow was mathematically modeled by using an integral method which accounts for natural fluid mechanisms such as turbulence, entrainment, buoyancy, and heat transfer. The analytical results are supported by experimental data and demonstrate the usefulness of the theory for estimating the trajectory and flow properties of the jet for a variety of injection conditions. The capability of predicting jet flow properties, as well as two- and three-dimensional jet paths, was enhanced by obtaining the jet cross-sectional area during the solution of the conservation equations. Realistic estimates of temperature in the jet fluid were acquired by accounting for heat losses in the jet flow due to forced convection and to entrainment of free-stream fluid into the jet.

Campbell, J. F.↗
NASA NTRS1973

Experimental wake survey behind Viking 75 entry vehicle at angles of attack of 0 deg, 5 deg, and 10 deg, Mach numbers from 0.20 to 1.20, and longitudinal stations from 1.50 to 11.00 body diameters

An investigation was conducted to obtain flow properties in the wake of a preliminary configuration of the Viking '75 Entry Vehicle at Mach numbers from 0.20 to 1.20 and at angles of attack of 0 deg, 5 deg, and 10 deg. The wake flow properties were calculated from total and static pressures measured with a pressure rake at longitudinal stations varying from 1.50 to 11.00 body diameters, and are presented in tabulated and plotted form. The wake properties were essentially symmetrical about the X-axis at alpha = 0 deg and the profiles were shifted away from the X-axis at angles of attack. An unexpected reduction in wake property ratios occurred as the Mach number increased from 0.60 to 1.00; these ratios then increased as the Mach number increased to 1.20. The reduction was present for all the longitudinal stations of the tests and decreased with increased longitudinal distance.

Brown, C. A., Jr.↗
NASA NTRS1973

Evaluation of experimental flow properties in the wake of a Viking '75 entry vehicle.

An experimental investigation has been conducted to obtain the flow properties in the wake of a model of the Viking '75 entry vehicle. Data are presented for the model at several angles of attack at free-stream Mach numbers from 0.2 to 3.95. The characteristics of the wake flow field are discussed and results are shown to demonstrate the significant variation of wake center-line flow properties in the transonic speed range, the shift in wake profiles with change in angle of attack, and the similarity exhibited by the velocity profiles across the wake.

Campbell, J. F.↗
NASA NTRS1973

Evaluation of flow properties behind 120 deg and 140 deg included-angle cones and a Viking 1975 entry vehicle at Mach numbers from 1.60 to 3.95

The flow properties in the wake of 120 degree and 140 degree included angle cones and a model of the preliminary configuration of the Viking 75 entry vehicle were evaluated. Wake flow properties were calculated from total and static pressures measured with a pressure-survey rake. Data are presented for free stream Mach numbers from 1.60 to 3.95, longitudinal stations from 1.0 to 8.39 body diameters downstream of the maximum diameter, and vertical stations from plus 1.04 to minus 1.04 body diameters measured from the wake center line for an angle of attack of zero degrees.

Brown, C. A., Jr.↗
NASA NTRS1972

Analysis of the Injection of a Heated, Turbulent Jet into a Moving Mainstream, with Emphasis on a Thermal Discharge in a Waterway

An experimental and theoretical investigation was undertaken to study the trajectory and growth of thermal effluents having a range of discharge velocities and temperatures. The discharge of a turbulent effluent into a waterway was mathematically modeled as a submerged jet injection process by using an integral method which accounts for natural fluid mechanisms such as turbulence, entrainment, buoyancy, and heat transfer. The analytical results are supported by experimental data and demonstrate the usefulness of the theory for estimating the location and size of the effluent with respect to the discharge point. The capability of predicting jet flow properties, as well as two- and three-dimensional jet paths, was enhanced by obtaining the jet cross-sectional area during the solution of the conservation equations. Realistic estimates of temperature in the effluent were acquired by accounting for heat losses in the jet flow due to forced convection and to entrainment of free-stream fluid into the jet.

Campbell, J. F.↗
NASA NTRS1972

Flow properties of submerged heated effluents in a waterway.

An experimental and theoretical investigation has been undertaken to study the trajectory and growth of thermal effluents having a range of discharge velocities and temperatures. The discharge of an effluent into a waterway was mathematically modeled as a submerged jet injection process by using an integral method which accounts for natural fluid mechanisms such as turbulence, entrainment, buoyancy, and heat transfer. The effects of these mechanisms on the jet properties are examined along with the effects of nonuniformity in the free-stream velocity and temperature fields. The results are supported by experimental data and demonstrate the usefulness of the theory for estimating the location, size, and temperature of the thermal plume.

Campbell, J. F.↗
NASA NTRS1971

Experimental wake survey behind a 140 deg-included-angle cone at angles of attack of 0 deg and 5 deg, Mach numbers from 1.60 to 3.95, and longitudinal stations varying from 1.0 to 8.39 body diameters

The flow properties in the wake of a 140 deg-included-angle cone at Mach numbers from 1.60 to 3.95 and at angles of attack of 0 deg and 5 deg are discussed. The wake flow properties are calculated from total and static pressures measured with a pressure rake at longitudinal stations varying from 1.0 to 8.39 body diameters and at lateral stations varying from -0.42 to 3.0 body diameters. These measurements show a consistent trend throughout the range of Mach number and longitudinal distance and an increase in dynamic pressure with increasing longitudinal station.

Brown, C. A., Jr.↗
NASA NTRS1971

Experimental wake survey behind Viking 1975 entry vehicle at angles of attack of 0 deg and 5 deg, Mach numbers from 1.60 to 3.95, and longitudinal stations from 1.0 to 8.39 body diameters

An investigation was conducted to obtain flow properties in the wake of the Viking '75 entry vehicle at Mach numbers from 1.60 to 3.95 and at angles of attack of 0 deg and 5 deg. The wake flow properties were calculated from total and static pressures measured with a pressure rake at longitudinal stations varying from 1.0 to 8.39 body diameters and lateral stations varying from -0.42 to 3.0 body diameters. These measurements showed a a consistent trend throughout the range of Mach numbers and longitudinal distances and an increase in dynamic pressure with increasing downstream position.

Brown, C. A., Jr.↗