Engineering Papers⌕ Search

Engineering topics

Camarda, Charles J.

Publications and source records attributed to Camarda, Charles J..

27 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Preliminary thermal/structural analysis of a carbon-carbon/refractory-metal heat-pipe-cooled wing leading edge

This study presents preliminary thermal/structural analyses of a carbon-carbon/refractory-metal heat-pipe-cooled wing leading edge concept designed for an air breathing single-stage-to-orbit hypersonic vehicle. The concept features chordwise (i.e., normal to the leading edge) and spanwise (i.e., parallel to the leading edge) refractory-metal heat pipes which are completely embedded within a carbon-carbon primary structure. Studies of the leading edge were performed using nonlinear thermal and linear structural three-dimensional finite element analyses. The concept was shown to be thermally feasible within the limits of the assumptions made in the analyses when internal radiative cooling is present during ascent, and a three-dimensional carbon-carbon architecture is used. In addition, internal radiative cooling was found not to be necessary during descent. The linear stress analysis indicated excessively large thermal stresses in the rafractory metal walls of the heat pipes even though a soft layer of carbon was included between the heat pipe and the carbon-carbon structure in an attempt to reduce the thermal stresses. A nonlinear structural analysis may be necessary to properly model the response of the refractory-metal heat pipes.

Glass, David E.↗
NASA NTRS1989

Carbon/Carbon Panels Cooled By Heat Pipes

Durable and reusable high-temperature carbon/carbon heat-pipe structure operates at temperatures above 3,000 degree F (1,649 degree C) in vacuum or inert environment and up to 2,800 degree F (1,537 degree C) in oxidizing environment. New concept combines high-temperature heat-pipe and carbon/carbon technologies to extend both thermal structural capabilities of refractory-metal heat pipes and maximum heat-flux capability of carbon/carbon structures. Uses refractory-metal heat pipes embedded within carbon/carbon structure. Walls of heat pipes thin and contain working fluid (lithium or sodium) of heat pipe. Carbon/carbon acts as primary load-carrying part of structure. Heat pipes help to eliminate local hotspots and associated thermal gradients and stresses and to reduce peak surface temperatures of carbon/carbon to levels within capability of oxidation-resisting system.

Camarda, Charles J.↗
NASA NTRS1989

Reusable high-temperature heat pipes and heat pipe panels

A reusable, durable heat pipe which is capable of operating at temperatures up to about 3000 F in an oxidizing environment and at temperatures above 3000 F in an inert or vacuum environment is produced by embedding a refractory metal pipe within a carbon-carbon composite structure. A reusable, durable heat pipe panel is made from an array of refractory-metal pipes spaced from each other. The reusable, durable, heat-pipe is employed to fabricate a hypersonic vehicle leading edge and nose cap.

Camarda, Charles J.↗
NASA NTRS1989

Development of higher-order modal methods for transient thermal and structural analysis

A force-derivative method which produces higher-order modal solutions to transient problems is evaluated. These higher-order solutions converge to an accurate response using fewer degrees-of-freedom (eigenmodes) than lower-order methods such as the mode-displacement or mode-acceleration methods. Results are presented for non-proportionally damped structural problems as well as thermal problems modeled by finite elements.

Camarda, Charles J.↗
NASA NTRS1987

Application of formal optimization techniques in thermal/structural design of a heat-pipe-cooled panel for a hypersonic vehicle

Nonlinear mathematical programming methods are used to design a radiantly cooled and heat-pipe-cooled panel for a Mach 6.7 transport. The cooled portion of the panel is a hybrid heat-pipe/actively cooled design which uses heat pipes to transport the absorbed heat to the ends of the panel where it is removed by active cooling. The panels are optimized for minimum mass and to satisfy a set of heat-pipe, structural, geometric, and minimum-gage constraints. Two panel concepts are investigated: cylindrical heat pipes embedded in a honeycomb core and an integrated design which uses a web-core heat-pipe sandwich concept. The latter was lighter and resulted in a design which was less than 10 percent heavier than an all actively cooled concept. The heat-pipe concept, however, is redundant and can sustain a single-point failure, whereas the actively cooled concept cannot. An additional study was performed to determine the optimum number of coolant manifolds per panel for a minimum-mass design.

Camarda, Charles J.↗
NASA NTRS1987

An evaluation of higher-order model methods for calculating transient structural response

A higher-order modal method proposed by Leung for transient structural analysis entitled the force-derivative method is evaluated. This method repeatedly integrates by parts with respect to time the convolution-integral form of the structural response to produce successively better approximations to the contribution of the higher modes which are neglected in the modal summation. Comparisons are made of the force-derivative, the mode-displacement, and the mode-acceleration methods for several numerical example problems for various times, levels of damping, and forcing functions. The example problems include a tip-loaded cantilevered beam and a simply-supported multispan beam. The force-derivative method is shown to converge to an accurate solution in fewer modes than either the mode-displacement or the mode-acceleration methods. In addition, for problems in which there are a large number of closely-spaced frequencies whose mode shapes have a negligible contribution to the response, the force-derivative method is very effective in representing the effect of the important, but otherwise neglected, higher modes.

Camarda, Charles J.↗
NASA NTRS1987

An evaluation of higher-order modal methods for calculating transient structural response

The present study evaluates a higher-order modal method proposed by Leung for transient structural analysis entitled the force-derivative method. This method repeatedly integrates by parts with respect to time the convolution-integral form of the structural response to produce successively better approximations to the contribution of the higher modes which are neglected in the modal summation. Comparisons are made of the force-derivative, the mode-displacement, and the mode-acceleration methods for several numerical example problems for various times, levels of damping, and forcing functions. The example problems include a tip-loaded cantilevered beam and a simply-supported multispan beam. The force-derivative method is shown to converge to an accurate solution in fewer modes than either the mode-displacement or the mode-acceleration methods. In addition, for problems in which there are a large number of closely-spaced frequencies whose mode shapes have a negligible contribution to the response, the force derivative method is very effective in representing the effect of the important, but otherwise neglected, higher modes.

Camarda, Charles J.↗
NASA NTRS1986

Evaluation of several modal methods for transient structural analysis

The convergence properties of three modal methods for solving structural transient response (STR) problems are examined by comparing the accuracy of the total number of modes used to represent the responses. The goal is to identify a method which involves as few degrees of freedom as possible. Two mode superposition methods, the mode displacement method (MDM) and the mode acceleration method (MAM), are fitted with equivalent expressions for damped response. An error norm is employed to compare the accuracies of the methods in calculating displacements, moments, and shear forces for a viscously-damped cantilevered beam experiencing several dynamic loading conditions and levels of damping. The MAM converges quicker and uses fewer dof, mainly because it has a pseudo-static response term which accounts for some of the flexibility of higher modes. A third method, which integrates the convolution integral iteratively over time, generates a higher order approximation to the STR with a reduced number of modes. It converges fastest among the three, but requires definition of an appropriate forcing function. Finally, the MAM and MDM models are applied to study the effects of the forcing frequency and the initial conditions.

Camarda, Charles J.↗