Engineering Papers⌕ Search

Engineering topics

Burton, Sarah D.

Publications and source records attributed to Burton, Sarah D..

Method to derive the infrared complex refractive indices n(λ) and k(λ) for organic solids from KBr pellet absorption measurements

Obtaining the complex refractive index vectors $n($$\tilde{v})$ and $k($$\tilde{v})$ allows calculation of the (infrared) reflectance spectrum that is obtained from a solid in any of its many morphological forms. Here, we report an adaptation to the KBr pellet technique using two gravimetric dilutions to derive quantitative $n($$\tilde{v})$/$k($$\tilde{v})$ for dozens of powders with greater repeatability. The optical constants of bisphenol A and sucrose are compared to those derived by other methods, particularly for powdered materials. The variability of the $k$ values for bisphenol A was examined by 10 individual measurements, showing an average coefficient of variation for $k$ peak heights of 5.6%. Though no established standards exist, the pellet-derived $k$ peak values of bisphenol A differ by 11% and 31% from their single-angle- and ellipsometry-derived values, respectively. These values provide an initial estimate of the precision and accuracy of complex refractive indices that can be derived using this method. Limitations and advantages of the method are discussed, the salient advantage being a more rapid method to derive $n$/$k$ for those species that do not readily form crystals or specular pellets.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Preparation and Characterization Methods of Thin Layer Samples for Standoff Detection

Detection of analytes deposited on surfaces is crucial for many applications: Development of methods to prepare thin layers (e.g. ~5 to 100 µm) is important for both system design and field studies. In this work, solid and liquid analytes were deposited on painted and bare substrates including aluminum, glass, plastic, and concrete using an ExactaCoat ultrasonic spray coater. Laboratory hemispherical reflectance (HRF) spectra were collected for samples with different layer thicknesses so as to characterize both the composition and layer thickness. Preliminary results demonstrate that to prepare homogenous layers on surfaces, parameters such as substrate type, analyte solubility, vapor pressure, paint color, surface porosity, and surface roughness are all important. Liquid chemicals posed several issues during deposition: Diisopropyl methyl phosphonate evaporated from surfaces more quickly than the other chemicals and was thus not detected in the HRF experiments. Less volatile liquids, such as tributylphosphate, remained on the surface for the duration of the test, but a uniform layer thickness could not be obtained as the liquid pooled to one side when mounted at an angle. The deposition of solids (e.g., acetaminophen, caffeine and methylphosphonic acid) from volatile solvents such as chloroform also proved problematic due to streaking caused by rapid solvent evaporation. Solids deposited from ethanol, however, worked well on bare substrates. For most samples plotting the integrated infrared band strength vs. surface thicknesses showed a linear relationship, confirming that the surface loading can be controlled by programming the concentration and the number of passes on the ultrasonic sprayer.

Thin layer, deposition, infrared standoff, Hemisph↗

Nanoscale Mg-Depleted Layers Slow Carbonation of Forsterite (Mg 2 SiO 4 ) When Water Is Limited

Passivation of silicate surfaces by accumulated reaction products is an obstacle to efficient CO 2 mineralization. In this study, we investigate a unique passivation effect during the carbonation of the basalt mineral forsterite (Mg 2 SiO 4 ) in humid supercritical CO 2 (50 °C, 90 bar). Using in situ high-pressure infrared spectroscopy, we demonstrate that dissolution of forsterite into a thin water film slows significantly after reaction for ˜24 h, even under far-from-equilibrium conditions. Further, 29 Si magic angle spinning nuclear magnetic resonance spectroscopy detects a highly polymerized amorphous silica at this stage. On the basis of transmission electron microscopy and energy dispersive X-ray spectroscopy, we show that the silica is present as a Mg-depleted layer that is just 2–3 nm thick on the reacted forsterite particles. The decrease in the level of forsterite dissolution in the presence of an extraordinarily thin Mg-depleted layer can be strongly linked to properties of the thin fluid film at the surface, highlighting the importance of water during mineral carbonation. This study furthers our understanding of silicate mineral carbonation under select low-water, humidified fluid conditions relevant to basaltic geologic reservoirs, recovery of critical elements by carbonation of mafic ores, and sequestration of atmospheric CO 2 by enhanced rock weathering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗