Engineering topics
Publications and source records attributed to Burger, Dale R..
A total of four different types of coverglass/filter combinations were tested over a 0 to 85 degree angle of incidence range. One group of cells was irradiated to provide additional data.
Passive functional tests are required to monitor the health of Mars Pathfinder solar arrays. To accomplish this, a Solar Array Ground Support Equipment Testbed (SAGSET) was proposed with five passive tests to be performed in sequence:.
Method of testing thermophotovoltaic (TPV) cells involves maintaining cells at various temperatures while exposing cells to black-body radiation at various intensities from black-body sources at various other temperatures. Provides for simulation and evaluation of performance under variety of operating conditions and could become standard testing method for government and industry.
The issues associated with characterization and testing thermophotovoltaic and multijunction cells are discussed.
Literature on solar array angle of incidence corrections was found to be sparse and contained no tabular data for support. This lack along with recent data on 27 GaAs/Ge 4 cm by 4 cm cells initiated the analysis presented in this paper. The literature cites seven possible contributors to angle of incidence effects: cosine, optical front surface, edge, shadowing, UV degradation, particulate soiling, and background color. Only the first three are covered in this paper due to lack of sufficient data. The cosine correction is commonly used but is not sufficient when the incident angle is large. Fresnel reflection calculations require knowledge of the index of refraction of the coverglass front surface. The absolute index of refraction for the coverglass front surface was not known nor was it measured due to lack of funds. However, a value for the index of refraction was obtained by examining how the prediction errors varied with different assumed indices and selecting the best fit to the set of measured values. Corrections using front surface Fresnel reflection along with the cosine correction give very good predictive results when compared to measured data, except there is a definite trend away from predicted values at the larger incident angles. This trend could be related to edge effects and is illustrated by a use of a box plot of the errors and by plotting the deviation of the mean against incidence angle. The trend is for larger deviations at larger incidence angles and there may be a fourth order effect involved in the trend. A chi-squared test was used to determine if the measurement errors were normally distributed. At 10 degrees the chi-squared test failed, probably due to the very small numbers involved or a bias from the measurement procedure. All other angles showed a good fit to the normal distribution with increasing goodness-of-fit as the angles increased which reinforces the very small numbers hypothesis. The contributed data only went to 65 degrees from normal which prevented any firm conclusions about extreme angle effects although a trend in the right direction was seen. Measurement errors were estimated and found to be consistent with the conclusions that were drawn. A controlled experiment using coverglasses and cells from the same lots and extending to larger incidence angles would probably lead to further insight into the subject area.
The Mars Pathfinder mission has three different solar arrays each of which sees changes in incidence angle during normal operation. When solar array angle of incidence effects was researched little published data was found. The small amount of-published data created a need to obtain and evaluate such data. The donation of the needed data, which was taken in the fall of 1994, was a major factor in the preparation of this paper.
A small radioisotope powered TPV system was assumed. The system was simplified into a one-dimensional model with the emitter and heat rejection system as boundaries. Design equations were then developed which would allow parametric modeling of system efficiency, emitter radiation incident upon the TPV cell, energy converted in the TPV cell, and energy absorbed in the filter and cell-to-cell gaps. A figure of merit was then developed for the emitter, filter, and TPV cell.
Design equations and parametric modeling can be used to define ranges of thermal, optical, and electrical system parameters in a small spacecraft thermophotovoltaic power system.
Surfaces emitting electromagnetic radiation predominantly in desired narrow spectral bands when heated made more durable, and fabricated less expensively, according to proposal. Narrowband thermal emitters made by polishing metal substrates to specularity, then coating specular surfaces with films of rare-earth oxides approximately less than 1 micrometer thick. Metal substrates inherently resistant to mechanical shock. Resistance to thermal shock achieved by choosing metals and rare-earth oxides having equal or nearly equal coefficients of thermal expansion.
This system design of a thermophotovoltaic (TPV) module is based upon low-bandgap photovoltaic cells.
The author discusses the photovoltaic array space power (PASP) experiment, which is designed to obtain data on the interaction between high-voltage photovoltaic arrays and the polar, low-earth plasma environment. Up to six small test arrays (three each of planar and concentrator designs) can be voltage biased over a range of +/- 500 V. During the bias voltage sequence, the array current leakage is measured and array arc events are monitored. If any arcing occurs the arc characteristics will be measured by a transient pulse monitor. An emitter is included to allow voltage bias to be applied to a plasma-charged or uncharged spacecraft. Similarly, the frames of the concentrator arrays can be left floating or can be tied to the negative array terminal. An environmental data scan is made before each bias voltage sequence. This scan collects information on the plasma, array-current-versus-voltage curves, and neutral particle partial pressure. The requirement for high voltages created problems which were met by circuit isolation and logical fault protection.
A method is disclosed for scribing at least three grid contacts of a photovoltaic cell to electrically isolate them from the grid contact pattern used to collect solar current generated by the cell, and using the scribed segments for determining parameters of the cell by a combination of contact end resistance (CER) measurements using a minimum of three equally or unequally spaced lines, and transmission line modal (TLM) measurements using a minimum of four unequally spaced lines. TLM measurements may be used to determine sheet resistance under the contact, R.sub.sk, while CER measurements are used to determine contact resistivity, .rho..sub.c, from a nomograph of contact resistivity as a function of contact end resistance and sheet resistivity under the contact. In some cases, such as the case of silicon photovoltaic cells, sheet resistivity under the contact may be assumed to be equal to the known sheet resistance, R.sub.s, of the semiconductor material, thereby obviating the need for TLM measurements to determine R.sub.sk.