Engineering Papers⌕ Search

Engineering topics

Brown, K. G.

Publications and source records attributed to Brown, K. G..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Recent advances in CO2 laser catalysts

This paper discusses several recent advances in CO2 laser catalysts including comparisons of the activity of Au/MnO2 to Pt/SnO2 catalysts with possible explanations for observed differences. The catalysts are compared for the effect of test gas composition, pretreatment temperature, isotopic integrity, long term activity, and gold loading effects on the Au/MnO2 catalyst activity. Tests conducted to date include both long-term tests of up to six months continuous operation and short-term tests of one week or more that include isotopic integrity testing.

Upchurch, B. T.↗
NASA NTRS1987

Catalytic Oxidation of CO for Closed-Cycle CO2 Lasers

Stoichiometric mixture converted completely. High-energy pulsed CO2 lasers have potential for measuring many different features of atmosphere of Earth and particularly useful on airborne or space platforms. For this application, laser must be operated in closed cycle to conserve gas, especially if rare nonradioactive isotopes of carbon and oxygen used. However, laser discharge decomposes fraction of CO2 to CO and O2, causing rapid loss in power leading to erratic behavior. To maintain operation, CO and O2 must be recombined to form CO2.

Miller, I. M.↗
NASA NTRS1987

Characterization of Pt/SnO2 catalysts for CO oxidation

Results are presented of surface characterization of 2% and 1% (w/w) Pt on SnO2 catalysts which are being used in promoting the oxidation of CO in pulsed CO2 lasers. The N2 adsorption BET surface area for both catalysts is 6.9 sq m/g. The CO chemisorbed area at 313K is 0.17 sq m/g and 0.062 sq m/g for the 2% and 1% catalysts, respectively. Monitoring the reaction between CO and O2 by the same technique, at the same temperature yields a turn-over frequency (TOF) for the 2% catalyst of 2.7 x 100 molecules of CO2/site/s and for the 1% catalyst a value of 1.2 x 100. The ratio of the TOFs for the two catalysts is 2.2 which is approximately the ratio of the Pt loading.

Brown, K. G.↗
NASA NTRS1986

Mass spectrometric gas composition measurements associated with jet interaction tests in a high-enthalpy wind tunnel

Knowledge of test gas composition is important in wind-tunnel experiments measuring aerothermodynamic interactions. This paper describes measurements made by sampling the top of the test section during runs of the Langley 7-Inch High-Temperature Tunnel. The tests were conducted to determine the mixing of gas injected from a flat-plate model into a combustion-heated hypervelocity test stream and to monitor the CO2 produced in the combustion. The Mass Spectrometric (MS) measurements yield the mole fraction of N2 or He and CO2 reaching the sample inlets. The data obtained for several tunnel run conditions are related to the pressures measured in the tunnel test section and at the MS ionizer inlet. The apparent distributions of injected gas species and tunnel gas (CO2) are discussed relative to the sampling techniques. The measurements provided significant real-time data for the distribution of injected gases in the test section. The jet N2 diffused readily from the test stream, but the jet He was mostly entrained. The amounts of CO2 and Ar diffusing upward in the test section for several run conditions indicated the variability of the combustion-gas test-stream composition.

Lewis, B. W.↗
NASA NTRS1985

Quasi non-intrusive sampling and analysis of gases associated with the boundary layer on the tethered satellite and similar supersonic and hypersonic research vehicles

The effect that one candidate inlet, an assembly of capillary openings in a thin glass plate (a multichannel plate), might have on the overall sampling process is considered. The flow characteristics of the plate, under a variety of conditions of external pressure and mass flow, is evaluated. A review of capillary flow theory is presented with some development of the pertinent equations. The predicted mass flow will be compared to that determined perimentally to assess the effect that mass flow through one capillary might have upon a neighboring capillary. Mass spectrometric measurements of mixtures flowing through the multichannel plate (MCP) is also considered. In the first part of the experiments, the flow was in a direction normal to the surface of the plate. The experimental gases were Argon and mixtures of carbon dioxide in air. Ongoing experiments are discussed which are conducted with the flow parallel to the surface of the plate, a simulation of the kind of flow that a flight vehicle would experience.

Fishel, C.↗
NASA NTRS1985

Candidate techniques for non-intrusive measurement of flight boundary-layer properties

Techniques to measure gas composition and chemical activity in the hypersonic boundary layer associated with entry research vehicles and with a tethered satellite deployed at 100-125 km altitude are currently being investigated at the NASA-Langley Research Center. These measurements are appropriate for the study of the aerothermodynamic properties of these vehicles when operating with controlled trajectories in the thermosphere between 125 and 55 km. A number of the required quantitative physical measurements have been identified, and candidate techniques to obtain the measurements without perturbing the flow are being considered. Two candidate techniques are discussed in this paper: a mass spectrometer to analyze the gas composition at the vehicle surface, and Rayleigh scattering to obtain density, velocity, and temperature gradients from the surface to the edge of the boundary layer.

Wood, G. M., Jr.↗
NASA NTRS1985

Aerothermodynamic heating and performance analysis of a high-lift aeromaneuvering AOTV concept

The thermal-control requirements for design-optimized aeromaneuvering performance are determined for space-based applications and low-earth orbit sorties involving large, multiple plane-inclination changes. The leading-edge heating analysis is the most advanced developed for hypersonic-rarefied flow over lifting surfaces at incidence. The effects of leading-edge bluntness, low-density viscous phenomena, and finite-rate flow-field chemistry and surface catalysis are accounted for. The predicted aerothermodynamic heating characteristics are correlated with thermal-control and flight-performance capabilities. The mission payload capability for delivery, retrieval, and combined operations is determined for round-trip sorties extending to polar orbits. Recommendations are given for future design refinements. The results help to identify technology issues required to develop prototype operational systems.

Menees, G. P.↗
NASA NTRS1985

Chemical and thermal nonequilibrium heat transfer analysis for hypervelocity, low Reynolds number flow

Chemical and thermal nonequilibrium phenomena are studied in the stagnation region of a hypervelocity blunt body. This investigation is motivated by the need to predict the heat transfer rate to the leading edge of Aeromaneuvering Orbital Transfer Vehicles. Flight speeds of approximately 10 km/s at altitudes of approximately 80 km are considered for body radii of 1 to 50 cm. The analysis is based on continuum theory and is applicable to the viscous-layer and incipient-merged-layer rarefied-flow regimes. A two-species, two-temperature gas model is assumed. Comparisons are made with previous theories, experimental data, and results based on the thermodynamic equilibrium assumption. The equation accounting for vibrational nonequilibrium is presented and its effects on flow properties are discussed. Parameters which require further investigation are identified. Preliminary results indicate that the inclusion of vibrational relaxation has little effect on heat transfer rate for a catalytic surface. However, vibrational nonequilibrium may increase the heat transfer rate to a noncatalytic surface, depending on the degree of nonequilibrium.

Brown, K. G.↗
NASA NTRS1985

Optimization of the catalytic oxidation of CO for closed-cycle CO2 laser applications

This report develops a basis for the design of a catalyst bed for the recombination of CO and O2 in a closed-cycle CO2 laser system. The catalyst is 1% Pt on SnO2 having a BET surface area of 6.7 sq m/g and a specific void volume of 0.374 cu cm/g. The design conditions are: a catalyst bed temperature of 100 C and a circulating flow rate of 10 lambda/min. Under these conditions, the required quantity of catalyst for prolonged laser operation of 668g. The rat law for the reaction of a stoichiometric mixture of 1% CO + 1/2% O2 in helium was determined to be overall first order; however, additional experiments with non-stoichiometric gas mixtures of CO and O2 are needed to determine the order of the CO concentration and the order of the O2 concentration in the rate law.

Miller, I. M.↗
NASA NTRS1985

Determination of atmospheric density using a space-launched projectile

A method is proposed that provides advance information about unpredictable atmospheric density dispersions that must be accommodated during random operations of aeroassisted-orbital-transfer vehicles (AOTVs). The principal feature is that a test or 'scout' projectile precedes the AOTV through the same region of the atmosphere as that of the predicted transatmospheric flight trajectory. The atmospheric density structure is determined from the vehicle's aerodynamic deceleration characteristics by on-board or ground-based tracking equipment. The time lag between passage of the projectile and the AOTV can be adjusted to only that time necessary to implement required guidance, navigation, and control (GN&C) corrections. The various strategies available to control the projectile's flight characteristics are analyzed in detail. The results are correlated with aerothermodynamic heating and materials requirements to ensure the survival of the projectile and, consequently, the capability of the AOTV to navigate a variable upper atmosphere within specified limits.

Menees, G. P.↗
NASA NTRS1984

Aerothermodynamic heating analysis of aerobraking and aeromaneuvering orbital-transfer vehicles

The thermal-protection requirements of two aeroassisted orbital-transfer vehicles (AOTVs) are analyzed for return missions between the geosynchronous and Shuttle orbits. One of the designs is a specialized version of a previously proposed generic aerobraking vehicle that is capable of only delivery-type operations. The other is a high-lift aeromaneuvering vehicle that is optimized for low-earth orbit sortie missions involving large, multiple plane-inclination changes. The aerothermal environment of the aerobraking vehicle is analyzed using state-of-the-art methods for nonequilibrium-radiative and convective heating that incorporate refinements unique to the configuration. The heating analysis of the aeromaneuvering vehicle required the development of a flow-field model for rarefied-hypersonic flow over a lifting surface at incidence. The predicted aerothermodynamic heating characteristics for both vehicles are correlated with thermal-control requirements and flight performance capabilities for the specified mission guidelines. The results help identify technical issues related to the development of future operational systems.

Davies, C. B.↗
NASA NTRS1984

Analysis of flow dynamics through small diameter gas sampling systems

The removal of gas material through a capillary opening in a surface is analyzed. The gas, from which the sample is removed, is moving past the surface at supersonic velocities. A variety of possible conditions of temperature, pressure and composition are discussed in an effort to emulate conditions that might be found at the surface of a vehicle traversing the altitude range 100-50 km, or might exist at the surface of a model in the stream of a high enthalpy wind tunnel. Aspects discussed include: (1) the throughput of the capillary for conditions of different lengths and different L/a (length/radius) ratios; (2) the total throughput when the surface in question contains many hundreds of these capillaries; (3) the effect of the capillaries upon the composition of the analyzed gas; (4) the effect of the capillary or capillaries upon the gas stream itself; and (5) the implications of the calculations upon the possible implementation of this type of device as an inlet for a mass spectrometer to be developed for analyzing the upper atmosphere.

Brown, K. G.↗
NASA NTRS1983

Analysis of an effusive sampling device for analysis of boundary layer gases

The effect of suction, through an opening in a surface, upon a stream of flowing gas is determined. The quantity of interest is the maximum distance, Y, from the surface that the main stream is affected by the applied suction. The fraction of this distance Y of the boundary layer thickness sigma is determined as a function of tubing radius and length, gas pressure, temperature and stream velocity. The shape of the flow in the high velocity stream is assumed to be determined by means of a parameter which is an unknown function of the distance from the leading edge of the surface.

Brown, K. G.↗