Engineering topics

Brown, Jeff

Publications and source records attributed to Brown, Jeff.

9 records

NASA NTRS2016

Consolidated Laser-Induced Fluorescence Diagnostic Systems for the NASA Ames Arc Jet Facilities

The spectroscopic diagnostic technique of two photon absorption laser-induced fluorescence (TALIF) of atomic species for non-intrusive arc jet flow property measurement was first implemented at NASA Ames in the mid-1990s. Use of TALIF expanded at NASA Ames and to NASA Johnsons arc jet facility in the late 2000s. In 2013-2014, NASA combined the agency's large-scale arc jet test capabilities at NASA Ames. Concurrent with that effort, the agency also sponsored a project to establish two comprehensive LIF diagnostic systems for the Aerodynamic Heating Facility (AHF) and Interaction Heating Facility (IHF) arc jets. The scope of the project enabled further engineering development of the existing IHF LIF system as well as the complete reconstruction of the original AHF LIF system. The updated LIF systems are identical in design and capability. They represent the culmination of over 20 years of development experience in transitioning a specialized laboratory research tool into a measurement system for large-scale, high-demand test facilities. This paper documents the overall system design from measurement requirements to implementation. Representative data from the redeveloped AHF and IHF LIF systems are also presented.

thermal protection materials↗

NASA NTRS2011

Shape Memory Alloy Actuator Design: CASMART Collaborative Best Practices

Upon examination of shape memory alloy (SMA) actuation designs, there are many considerations and methodologies that are common to them all. A goal of CASMART's design working group is to compile the collective experiences of CASMART's member organizations into a single medium that engineers can then use to make the best decisions regarding SMA system design. In this paper, a review of recent work toward this goal is presented, spanning a wide range of design aspects including evaluation, properties, testing, modeling, alloy selection, fabrication, actuator processing, design optimization, controls, and system integration. We have documented each aspect, based on our collective experiences, so that the design engineer may access the tools and information needed to successfully design and develop SMA systems. Through comparison of several case studies, it is shown that there is not an obvious single, linear route a designer can adopt to navigate the path of concept to product. SMA engineering aspects will have different priorities and emphasis for different applications.

Benafan, Othmane↗

NASA NTRS2006

Effect of Thermomechanical Processing on the Microstructure, Properties, and Work Behavior of a Ti50.5 Ni29.5 Pt20 High-Temperature Shape Memory Alloy

TiNiPt shape memory alloys are particularly promising for use as solid state actuators in environments up to 300 C, due to a reasonable balance of properties, including acceptable work output. However, one of the challenges to commercializing a viable high-temperature shape memory alloy (HTSMA) is to establish the appropriate primary and secondary processing techniques for fabrication of the material in a required product form such as rod and wire. Consequently, a Ti(50.5)Ni(29.5)Pt20 alloy was processed using several techniques including single-pass high-temperature extrusion, multiple-pass high-temperature extrusion, and cold drawing to produce bar stock, thin rod, and fine wire, respectively. The effects of heat treatment on the hardness, grain size, room temperature tensile properties, and transformation temperatures of hot- and cold-worked material were examined. Basic tensile properties as a function of temperature and the strain-temperature response of the alloy under constant load, for the determination of work output, were also investigated for various forms of the Ti(50.5)Ni(29.5)Pt20 alloy, including fine wire.

Noebe, Ronald↗

NASA NTRS2000

The Sandmeier Field Goniometer: A Measurement Tool for Bi-Directional Reflectance

Recent activities at the Remote Sensing Program at Stennis Space Center have identified the need to properly verify and validate data provided by the remote sensing community. One important variable, which effects remote sensing data is bi-directional reflectance distribution (BRDF). In order to quantify the effects of BRDF on man-made and natural ground targets, the Stennis Verification & Validation (V&V) team commissioned the Systems Engineering Division at NASA Ames Research Center to develop a Field Goniometer for use at the V&V Large Target Range and for various ground truthing missions. The Swiss Field Goniometer (FIGOS) was used as a benchmark instrument to design the new state of the art Sandmeier Field Goniometer (SGF), named after Stefan Sandmeier, developer of FIGOS. After establishing requirements for the SFG, design efforts began in early May 1998. The design of the SFG was completed in September 1998. Manufacturing, construction, and testing was completed in May 1999. The SFG was shipped to NASA SSC and fully operational by June 1999.

Turner, Mark↗

NASA NTRS1998

Development of a mirror pointing mechanism for an atmospheric gas measurement instrument

Development of the Open Path Tunable Infrared Monitor of the Atmosphere (OPTIMA) instrument involved designing a pair of motion systems that could maintain a precise alignment and spatial distance between two mirrors installed on the NASA DC-8 research laboratory aircraft. This is the first airborne optical instrument that allows direct measurement of the gases in the freestream airflow on the exterior of the aircraft. One mirror is mounted within a specially constructed open port cavity in the cabin of the aircraft and the second is mounted 6 meters away on top of the inboard port side (number 2) engine pylon. Three co-aligned laser beams are reflected between the two mirrors 64 times in a Herriott pattern. The resulting sample path length of 384 meters is used to perform a spectral absorption analysis of the airflow between the mirrors. To compensate for normal wing movement and engine oscillations both mirrors were designed as continuously driven mechanisms to maintain alignment within allowable limits. The motion systems of the two mirror assemblies provide five degrees of freedom and are designed to maintain a pointing accuracy within seven arc-sec with a response frequency in excess of 10 Hz. The pylon motion system incorporates controlled pitch and yaw movement. The fuselage motion system compensates for pitch variation as well as linear translation for focal length and vertical aiming of the laser beam via a controlled beam guidance mechanism.

Graham, Michael↗

NASA NTRS1993

An experimental study of a turbulent boundary layer in the trailing edge region of a curculation-control airfoil

This report discusses progress made on NASA Cooperative Agreement NCC2-545, 'An Experimental Study of a Turbulent Boundary Layer in the Trailing-Edge Region of a Circulation-Control Airfoil,' during the period 1 Oct. 1992 - 30 Jun. 1993. The study, being conducted by Jeff Brown of the Eloret Institute, in conjunction with the Experimental Fluid Dynamics Branch at NASA Ames (Dennis Johnson, technical monitor), features 2-component laser Doppler velocimeter (LDV) measurements in the trailing edge and wake regions of a generic circulation-control airfoil model. The final experimental phase of the study will be carried out in the Ames High Reynolds Number Channel II (HRC2) transonic blow-down facility. During the 9-month period covered by this report, important data were acquired using the near-wall laser Doppler velocimeter (LDV) whose development has been described in previous reports. These data point strongly to the viability of this new technique for measuring the full Reynolds Stress Tensor in 3D flows.

Brown, Jeff↗

NASA NTRS1992

An experimental study of a turbulent boundary layer in the trailing edge region of a circulation-control airfoil

This report discusses progress made on NASA Cooperative Agreement NCC2-545, 'An Experimental Study of a Turbulent Boundary Layer in the Trailing-Edge Region of a Circulation-Control Airfoil' during the period 9/1/91 through 9/30/92. The study features 2-component laser Doppler velocimeter (LDV) measurements in the trailing edge and wake regions of a generic 2-dimensional circulation-control model. The final experimental phase of the study will be carried out in the Ames High Reynolds Number Channel 2 (HRC2) transonic blow-down-facility. During the 13-month period covered by this report, work continued on the development of the near-wall laser Doppler velocimeter (LDV) described in previous reports.

Heinemann, K.↗

NASA NTRS1991

Digital Pitch-And-Roll Monitor

Highly accurate inclinometer developed. Monitors both pitch and roll simultaneously and provides printed output on demand. Includes three mutually perpendicular accelerometers and signal-conditioning circuitry converting outputs of sensors to digital values of pitch and roll. In addition to wind-tunnel applications, system useful in any application involving steady-state, precise sensing of angles, such as calibration of robotic devices and positioners.

Finley, Tom D.↗

NASA NTRS1988

A manned lunar outpost. Design considerations for three key elements in an initial manned lunar outpost

The Initial Manned Lunar Outpost (IMLO) is proposed as the initial permanent base for manned activities on the Moon. The study concentrated on identifying the equipment, support systems, and initial base configuration necessary to accomplish the various science, industrial and exploration activities planned. The primary concepts of the MLO were the use of hard modules for habitation areas creating a flexible, modular transportation system; designing a multi-functional vehicle; and using an overhead radiation protection system. The transportation system, dubbed the Lunar Mobile Surface Transport System (LMSTS), carries the hard modules to the surface of the moon and provides a method to move them to the desired location through the use of interchangeable pallets. The avionics pallets are changed-out with wheel and hitch pallets, transforming the LMSTS into a "tractor trailer" used with the Multi-Functional Vehicle (MFV). The modules are placed under the Regolith Support Structure (RSS) which provides a stable environment and radiation protection for the entire base. The overhead structure was chosen over simply burying the modules to provide a study on the advantages and disadvantages of this type of system. The advantages include easy access to the exterior of the modules, providing a protected area for vehicles and equipment used in EVA, and creating an area of constant temperature. Disadvantages include a need for prefabrication of structural components, including the preconstruction and construction phases of the initial MLO. The design approach taken considered existing and near-term materials and technology only, without the consideration of possible future building technologies.

Bell, Larry↗