Engineering topics
Brown, Donald W.
Publications and source records attributed to Brown, Donald W..
Phase Identification in Synchrotron X-ray Diffraction Patterns of Ti–6Al–4V Using Computer Vision and Deep Learning
X-ray diffraction patterns contain information about the atomistic structure and microstructure (defect population) of materials, extracting detailed information from diffraction patterns is complex, demanding and relies on prior knowledge. Here, we hypothesize that deep-learning techniques can help to perform an effective and accurate analysis with high throughput rates. To demonstrate this concept, we applied a novel deep learning framework to determine the evolution of the β-phase volume fraction in a Ti–6Al–4V alloy during heat-treatment from video sequences of 2D diffraction patterns recorded in transmission and with highly monochromatic radiation in a synchrotron beamline. In particular, we studied the impact of network design on prediction reliability and computational performance. Networks of different architectures were trained using 3008 experimental 2D patterns. A well-tuned model was found to reproduce the phase fractions of another experimental data set, consisting of 1100 diffraction patterns, with a mean-square error as small as 2.6 x 10 -4 . The average prediction error of β-phase volume fraction was within 1.6 x 10 -2 (in each diffraction pattern) of the values obtained by conventional methods. Our work demonstrates that convolutional neural networks can evaluate high energy X-ray diffraction patterns with a remarkable level of reliability. Furthermore, it demonstrates the significance of network design on the reliability of predictions and computational performance. The most complex models do not necessarily result in highest accuracy and may even fail to learn from the data.
Determination of single crystal thermal expansion in Uranium-6wt%Niobium shape memory alloy using in-situ diffraction and modeling of textured polycrystalline samples
In-situ neutron diffraction and ex-situ dilatometry experiments were performed on a chemically banded, quenched uranium-6wt% niobium shape memory alloy to study the impact of deformation-(detwinning-) induced texture on the evolution of thermally induced strains (and associated stresses). Thermal heating and cooling cycles between 5K and 473K were performed in-situ with neutron diffraction, and the lattice strain evolution is reported for the observed monoclinic α" phase. Comparisons between the measured diffraction strains and macroscopic dilatometry experiments reveal relationships between micro- and macro-level thermal expansion. Softening of the texture during heating suggests that twin boundary motion can accommodate the large internal thermal strains which are approximately 2% greater than that typically observed during the 175K heating interval used to age more randomly oriented polycrystalline material. Assuming weak constraint of neighboring grains in randomly textured polycrystals, the single crystal thermal expansion tensor is extracted from measurements of lattice strains over the range 5K to 473K. Predictions of polycrystalline thermal expansion, based upon this single crystal thermal expansion tensor, are shown to compare favorably with bulk thermal expansion observations of the as quenched microstructure. However, such a lower-bound estimate is insufficient to explain all aspects of the behavior of the textured material, where the matrix is not isotropic. In conclusion, it is hypothesized that relaxation processes which occur within the quenched microstructure during heating are responsible for the distinct thermal expansion behavior observed during the initial heating cycle compared to cooling and subsequent cycling.
Shock state distributions in porous tantalum and characterization with multipoint velocimetry
Heterogenous materials under shock compression can be expected to reach different shock states throughout the material according to local differences in microstructure and the history of wave propagation. Here, in this work, a compact, multiple-beam focusing optic assembly is used with high-speed velocimetry to interrogate the shock response of porous tantalum films prepared through thermal-spray deposition. The distribution of particle velocities across a shocked interface is compared to results obtained using a set of defocused interferometric beams that sampled the shock response over larger areas. The two methods produced velocity distributions along the shock plateau with the same mean, while a larger variance was measured with narrower beams. The finding was replicated using three-dimensional, mesoscopically resolved hydrodynamics simulations of solid tantalum with a pore structure mimicking statistical attributes of the material and accounting for radial divergence of the beams, with agreement across several impact velocities. Accounting for pore morphology in the simulations was found to be necessary for replicating the rise time of the shock plateau. The validated simulations were then used to show that while the average velocity along the shock plateau could be determined accurately with only a few interferometric beams, accurately determining the width of the velocity distribution, which here was approximately Gaussian, required a beam dimension much smaller than the spatial correlation lengthscale of the velocity field, here by a factor of ∼30×, with implications for the study of other porous materials.
Microstructure characterization and elastic-plastic self-consistent simulation studies of anisotropic deformation of β -tin
Uniaxial compression tests of 99.9% pure polycrystalline $β$-tin (Sn) were conducted at various strain rates (10 -3 /s, 10 -1 /s and 1/s) and temperatures (294 K and 193 K) to understand the effects of these variables on the stress–strain response, microstructure evolution, and stress relaxation behavior. Multiple Sn specimens were subjected to complex compressive loading/unloading/reloading paths at different strain rates. Specimens initially compressed at higher strain rates showed strain rate-dependent texture evolution and more pronounced relaxation upon reloading, as compared to those pre-strained at lower rates at room temperature (RT). Compression tests conducted at low temperature (193 K) revealed increased strength, similar to the enhanced strength observed when the strain rate was increased at RT. Neutron diffraction was employed to characterize the initial and final bulk textures of the RT specimens. Electron backscatter diffraction was utilized to examine the crystallographic grain orientation and morphology, thereby identifying the signatures of dislocation-mediated deformation, grain refinement, recrystallization, and twinning behaviors. Elastic-plastic self-consistent simulations were performed to investigate the deformation modes responsible for the strain rate-dependent macroscopic stress–strain response and texture evolution. Effects of crystallographic orientation on stress relaxation behavior was also examined. In conclusion, the model predictions are in reasonable agreement with experimental observations.
In Situ X-ray Diffraction Investigation of Hydrogen Effects on Deformation-Induced Phase Transformation in Forged and Additively Manufactured 304L Stainless Steels
Here, this study utilized high energy synchrotron x-ray diffraction to probe microstructural evolution during uniaxial deformation of conventionally manufactured and additively manufactured (AM) 304L stainless steel with and without internal hydrogen. The objective of this effort is to highlight the effect of hydrogen on deformation-induced martensite phase transformations in austenitic stainless steels. Solute hydrogen depresses the required applied strain to initiate austenite transformation to ε-martensite and α'-martensite in both forged and AM stainless steel. Similarly, the total fraction of transformation product is larger when the microstructure is saturated with hydrogen. Deformation induced phase transformations also lead to a variation in strain partitioning behavior, which is linked to the chemical composition and stacking fault energy of the starting and hydrogen-charged materials.
Deformation, dislocation evolution and the non-Schmid effect in body-centered-cubic single- and polycrystal tantalum
A physically-informed continuum crystal plasticity model is presented to elucidate deformation mechanisms, dislocation evolution and the non-Schmid effect in body-centered-cubic (bcc) tantalum widely used as a key structural material for mechanical and thermal extremes. We show the unified structural modeling framework informed by mesoscopic dislocation dynamics simulations is capable of capturing salient features of the large inelastic behavior of tantalum at quasi-static (10 -3 s -1 ) to extreme strain rates (5000 s -1 ) and at low (77 K) to high temperatures (873 K) at both single- and polycrystal levels. Here we also present predictive capabilities of the model for microstructural evolution in the material. To this end, we investigate the effects of dislocation interactions on slip activities, instability and the non-Schmid behavior at the single crystal level. Furthermore, ex situ measurements on crystallographic texture evolution and dislocation density growth are carried out for polycrystal tantalum specimens at increasing strains. Numerical simulation results also support that the modeling framework is capable of capturing the main features of the polycrystal behavior over a wide range of strains, strain rates and temperatures. The theoretical, experimental and numerical results at both single- and polycrystal levels provide critical insight into the underlying physical pictures for micro- and macroscopic responses and their relations in this important class of refractory bcc materials undergoing large inelastic deformations.
A Coupled Small and Wide-Angle X-Ray Scattering Study of Phase Transformation Mechanisms in U-6Wt Pct Nb
The elevated temperature phase transformation kinetics of U-6wt%Nb in both wrought and cast conditions were investigated using in-situ high energy synchrotron X-ray scattering. The evolution of the phase content, γ-phase composition, and microstructure morphology was determined through the analysis of simultaneously collected wide-angle diffraction and small-angle scattering (SAXS) data. The results of the wide-angle scattering analysis, especially the phase fractions and average composition of the γ-phase, provide model parameters to enable a quantitative analysis using the SAXS data. Greater clarity regarding the kinetics of different precipitation mechanisms, namely the continuous precipitation (CP) of α-U within the γ-phase matrix and the discontinuous (DP) grain boundary precipitation of a lamellar microstructure, consisting of α-U and Nb-rich γ-phase are obtained from the coupled measurement modes. These results indicate that the CP mechanism is responsible for the initial precipitation of α-U at all temperatures considered. Near the nose in the time-temperature-transformation (TTT) diagram at ~798 K, both mechanisms are active during the early stages of phase transformation. However, the DP mechanism has an increasingly long incubation period with decreasing temperature below the TTT nose. In conclusion, the average interlamellar spacing obtained from the SAXS analysis increases with time, providing further evidence of the so-called divergent DP behavior previously observed in U-6wt%Nb alloys.
Time-resolved phase and compositional homogenization of segregated uranium-niobium alloys above the monotectoid temperature
Not Available
The roles of kinematic constraint and diffusion in non-equilibrium solid state phase transformations of Ti-6Al-4V
A solid state phase transformation of Ti-6Al-4V was studied using high speed in situ x-ray diffraction measurements made during rapid cooling of a cold metal transfer arc weld bead deposited onto a water cooled substrate. Analysis of body centered cubic (BCC) and hexagonal close packed (HCP) lattices revealed an abrupt, nonlinear shift in the lattice parameters of both phases just after the HCP phase had nucleated. Postmortem transmission electron microscopy confirmed that V diffusion was mostly suppressed during cooling. Together, these results indicate that at this cooling rate of approximately 10 4 K/s, which is representative of cooling rates of many additive manufacturing and welding processes, kinematic coherency of the BCC–HCP interfaces gives rise to the anomalous lattice expansion and contraction behaviors of both phases during the initial nucleation and growth stages of (mostly) martensitic transformation from BCC to HCP; the role of diffusion in such lattice anomalies is shown to be minimal.
In-situ high-energy X-ray diffraction and crystal plasticity modeling to predict the evolution of te
Explore the source record for details and available documents.
Residual stress analysis of in situ surface layer heating effects on laser powder bed fusion of 316L stainless steel
Not Available
Tailoring Microstructure and Mechanical Properties of Additively-Manufactured Ti6Al4V Using Post Processing
Additively-manufactured Ti-6Al-4V (Ti64) exhibits high strength but in some cases inferior elongation to those of conventionally manufactured materials. Post-processing of additively manufactured Ti64 components is investigated to modify the mechanical properties for specific applications while still utilizing the benefits of the additive manufacturing process. The mechanical properties and fatigue resistance of Ti64 samples made by electron beam melting were tested in the as-built state. Several heat treatments (up to 1000 °C) were performed to study their effect on the microstructure and mechanical properties. Phase content during heating was tested with high reliability by neutron diffraction at Los Alamos National Laboratory. Two different hot isostatic pressings (HIP) cycles were tested, one at low temperature (780 °C), the other is at the standard temperature (920 °C). The results show that lowering the HIP holding temperature retains the fine microstructure (~1% β phase) and the 0.2% proof stress of the as-built samples (1038 MPa), but gives rise to higher elongation (~14%) and better fatigue life. The material subjected to a higher HIP temperature had a coarser microstructure, more residual β phase (~2% difference), displayed slightly lower Vickers hardness (~15 HV10N), 0.2% proof stress (~60 MPa) and ultimate stresses (~40 MPa) than the material HIP’ed at 780 °C, but had superior elongation (~6%) and fatigue resistance. Heat treatment at 1000 °C entirely altered the microstructure (~7% β phase), yield elongation of 13.7% but decrease the 0.2% proof-stress to 927 MPa. The results of the HIP at 780 °C imply it would be beneficial to lower the standard ASTM HIP temperature for Ti6Al4V additively manufactured by electron beam melting.
Perspectives on Quenching and Tempering 4340 Steel
Steels are ubiquitous due to their affordability and the landscape of useful properties that can be generated for engineering applications. But to further expand the performance envelope, one must be able to understand and control microstructure development by alloying and processing. In this paper we use multiscale, advanced characterization to better understand the structural and chemical evolution of AISI 4340 steel after quenching and tempering (Q&T), including the role of quench rate and short-time, isothermal tempering below 573 K (300 °C), with an emphasis on carbide formation. We compare the microstructure and/or property changes produced by conventional tempering to those produced by higher temperature, short-time “rapid” tempering. We underscore that no single characterization technique can fully capture the subtle microstructure changes like carbon redistribution, transition carbide and/or cementite formation, and retained austenite decomposition that occur during Q&T. Only the use of multiple techniques begins to unravel these complexities. After controlled fast or slow quenching, η transition carbides clearly exist in the microstructure, likely associated with autotempering of this high martensite start temperature (Ms) steel. Isothermal tempering below 598 K (325 °C) results in the relief of carbon supersaturation in the martensite, primarily by the formation of η transition carbides that exhibit a range of carbon levels, seemingly without substitutional element partitioning between the carbide and matrix phases. Hägg transition carbide is present between 300 °C and 325 °C. After conventional tempering at or above 598 K (325 °C) for 2 h, cementite is predominant, but small amounts of cementite are also present in other conditions, even after quenching. Previous work has indicated that silicon (Si) and substitutional elements partition between the cementite, which initially forms under paraequilibrium conditions, and the matrix. Phosphorous (P) may also be preferentially located at cementite/matrix interfaces after high temperature tempering. Slower quench rates result in greater amounts of retained austenite compared to those after fast quenching, which we attribute to increased austenite stability resulting from “autopartitioning”. Rapid, high temperature tempering is also found to diminish tempered martensite embrittlement (TME) believed to be associated with the extent of austenite decomposition, resulting in mechanical properties not attainable by conventional tempering, which may have important implications with respect to industrial heat treatment processes like induction tempering. Controlling the amount and stability of retained austenite is not only relevant to the properties of Q&T steels, but also next-generation advanced high strength steels (AHSS) with austenite/martensite mixtures.