Engineering Papers⌕ Search

Engineering topics

Brown, D. W.

Publications and source records attributed to Brown, D. W..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The Thermo-Elastic Properties and Damping of U-6wt%Nb

While thermal expansion data exists for quenched (as well as aged) U-6wt%Nb, there is wide variation in the reported room temperature elastic moduli. To better understand the room temperature elastic behavior and to address the complete absence of data on the temperature dependence of the elastic moduli, room temperature and in-situ elevated temperature resonant ultrasonic spectroscopy (RUS) was performed along with x-ray diffraction (XRD) and dilatometry using a thermomechanical analyzer (TMA). An in-situ small- and wide-angle x-ray scattering (SAXS/WAXS) experiment was performed on a companion sample to help interpret the results. The room temperature polycrystalline dynamic moduli were measured to be E = 95.4 ± 4.5 GPa and G = 35.2 ± 0.2 GPa, respectively. As the temperature is raised, the stiffness slowly decreases, consistent with the empirical rule proposed by Varshni, up to the point of precipitation of the equilibrium α-U phase, which is stiffer than the martensitic phases. Homogenization theory of composites can be used to rationalize the observed response at high temperatures and after high-temperature exposures. Further, aging of the material at low temperatures (≤200°C) does not affect the linear elastic stiffness, but does impact the damping behavior which can be measured through RUS. This change in damping provides another perspective on the microstructure changes induced by low-temperature aging which also result in significant strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2019

A Planar Biaxial Experiment Platform for In Situ High-Energy Diffraction Studies

In this work, an experimental platform for multiscale studies of materials subjected to plane stress loads is presented. Specifically, a planar biaxial mechanical load frame with four independent hydraulic actuators capable of applying arbitrary loading paths and ratios of tension and compression was designed and built for in situ diffraction experimentation. The load frame is integrated for use at the Argonne National Laboratory Advanced Photon Source (APS) synchrotron, Sector 1, 1-ID-E endstation and the Los Alamos Neutron Science Center (LANSCE) spallation neutron source, Spectrometer for Materials Research at Temperature and Stress (SMARTS) instrument. Cruciform specimen geometries were designed to experience loading ratios in the gauges commensurate with those applied at the grips, and to minimize interference with diffracted X-rays and neutrons. The finite element models used to design the cruciform specimen geometries were experimentally validated using stereo digital image correlation measurements. This complete planar biaxial in situ diffraction platform provides a new capability for studying multiaxial micromechanics of crystalline materials (e.g., elastic, slip, twinning, phase transformation) and their dependencies on grain size, location, texture, and neighborhood characteristics. The coupling with far-field high energy diffraction microscopy (ff-HEDM) for grain-by-grain measurements provides an additional benefit; provided crystal elastic constants of a material are known, it enables the direct measurement of local and average stress tensors in the gauge sections of cruciform specimens, resolving a long outstanding challenge of planar biaxial mechanical testing.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Directional and oscillating residual stress on the mesoscale in additively manufactured Ti-6Al-4V Mesoscale and anisotropic residual stress in additive manufacturing of Ti-6Al-4V

In additive manufacturing of metals as compared to conventional processing, the directional track-by-track and layer-by-layer nature of the fabrication process can lead to residual stresses that locally are both directionally and spatially heterogeneous. Much of the existing literature has focused either on the macroscale residual stress inside the entire part, or on the microscale residual stresses that are created around a scan vector, thereby neglecting the intermediate length-scale of the different layers. The objective of this research is to investigate such mesoscale residual stress distributions across several layers in Ti-6Al-4V components produced by laser metal deposition process. The incremental centre hole drilling and incremental slitting methods provide measurements with excellent spatial resolution within and across the layer length scale. Here in this work, the two methods complemented each other to quantify both mesoscale and directional variations of residual stress that correlate with the deposition pattern. Lastly, our findings also provide strong evidence that an oscillatory residual stress variation persists even after thermal cycling that occurs during deposition of subsequent layers.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Evaluation of a thermomechanical model for prediction of residual stress during laser powder bed fusion of Ti-6Al-4V

The build-up of residual stresses in a part during laser powder bed fusion provides a significant limitation to the adoption of this process. These residuals stresses may cause a part to fail during a build or fall outside the specified tolerances after fabrication. In the present work a thermomechanical model is used to simulate the build process and calculate the residual stress state for Ti–6Al–4V specimens built with continuous and island scan strategies. A layer agglomeration, or lumping, approach is used to speed up the computations. A material model is developed to naturally capture the strain-rate dependence and annealing behavior of Ti–6Al–4V at elevated temperatures. Conclusions from the thermomechanical simulations showed good agreement with synchrotron X-ray diffraction measurements used to determine the residual elastic strains in these parts. Yet, the experimental measurements showed higher residual strains for the specimen built with an island scan strategy; a trend not fully captured by the simulations. Parameter studies were performed to fully understand the advantages and limitations of the current simulation methodology. Reasons for both the computational and experimental findings are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Additive Manufacturing of a y0-Tetragonal Uranium-Niobium Alloy

The ability to process near-net shape structures is of particular interest in applications using rare or expensive materials. Laser powder bed fusion additive manufacturing can meet this challenge, yet also introduces significant processing and materials challenges toward achieving structural integrity. Broadly addressed aspects affecting powder bed fusion structures include surface roughness, residual stresses, and porosity. Here, we focus on materials-specific challenges—namely, the influence of multiple pass reheating during processing and post-processing homogenization on phase transformations and the role of impurities and oxides on grain morphology and mechanical behavior—with a view of adopting laser powder bed fusion processing for the shape memory alloy, uranium-6 wt.% niobium. Our observations to date on the factors influencing material behavior and post-processing requirements and recommendations for process improvement are discussed herein.

36 MATERIALS SCIENCE↗
DOE OSTI2017

In Situ Neutron Diffraction Study of the Influence of Microstructure on the Mechanical Response of Additively Manufactured 304L Stainless Steel

In situ neutron diffraction measurements were completed for this study during tensile and compressive deformation of stainless steel 304L additively manufactured (AM) using a high power directed energy deposition process. Traditionally produced wrought 304L material was also studied for comparison. The AM material exhibited roughly 200 MPa higher flow stress relative to the wrought material. Crystallite size, crystallographic texture, dislocation density, and lattice strains were all characterized to understand the differences in the macroscopic mechanical behavior. The AM material’s initial dislocation density was about 10 times that of the wrought material, and the flow strength of both materials obeyed the Taylor equation, indicating that the AM material’s increased yield strength was primarily due to greater dislocation density. Finally, a ~50 MPa flow strength tension/compression asymmetry was observed in the AM material, and several potential causes were examined.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Mechanical Behavior of Additively Manufactured Uranium-6 wt. pct. Niobium

This report describes an effort to process uranium-6 weight% niobium using laser powder bed fusion. The chemistry, crystallography, microstructure and mechanical response resulting from this process are discussed with particular emphasis on the effect of the laser powder bed fusion process on impurities. In an effort to achieve homogenization and uniform mechanical behavior from different builds, as well as to induce a more conventional loading response, we explore post-processing heat treatments on this complex alloy. Elevated temperature heat treatment for recrystallization is evaluated and the effect of recrystallization on mechanical behavior in laser powder bed fusion processed U-6Nb is discussed. Wrought-like mechanical behavior and grain sizes are achieved through post-processing and are reported herein.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Deformation behavior of additively manufactured GP1 stainless steel

In-situ neutron diffraction measurements were performed in this paper during heat-treating and uniaxial loading of additively manufactured (AM) GP1 material. Although the measured chemical composition of the GP1 powder falls within the composition specifications of 17-4 PH steel, a fully martensitic alloy in the wrought condition, the crystal structure of the as-built GP1 material is fully austenitic. Chemical analysis of the as-built material shows high oxygen and nitrogen content, which then significantly decreased after heat-treating in a vacuum furnace at 650 °C for one hour. Significant austenite-to-martensite phase transformation is observed during compressive and tensile loading of the as-built and heat-treated material with accompanied strengthening as martensite volume fraction increases. During loading, the initial average phase stress state in the martensite is hydrostatic compression independent of the loading direction. Finally, preferred orientation transformation in austenite and applied load accommodation by variant selection in martensite are observed via measurements of the texture development.

36 MATERIALS SCIENCE↗
DOE OSTI2016

High energy X-ray diffraction study of the relationship between the macroscopic mechanical properties and microstructure of irradiated HT-9 steel

Samples harvested from an HT-9 fuel test assembly (ACO-3) irradiated for six years in the Fast Flux Test Facility (FFTF) reaching 2–147 dpa at 382–504°C were deformed in-situ while collecting high-energy X-ray diffraction data to monitor microstructure evolution. With the initiation of plastic deformation, all samples exhibited a clear load transfer from the ferrite matrix to carbide particulate. This behavior was confirmed by modeling of the control material. The evolution of dislocation density in the material as a result of deformation was characterized through full pattern line profile analysis. The dislocation densities increased substantially after deformation, the level of dislocation evolution observed was highly dependent upon the irradiation temperature of the sample. The differences in both the yield and hardening behavior between samples irradiated at higher and lower temperatures suggest the existence of a transition in tensile behavior at an irradiation temperature near 420°C dividing regions of distinct damage effects.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Elastic Properties of Rolled Uranium -- 10 wt.% Molybdenum Nuclear Fuel Foils

In situ neutron diffraction data was collected during elastic loading of rolled foils of uranium-10 wt.% molybdenum bonded to a thin layer of zirconium. Lattice parameters were ascertained from the diffraction patterns to determine the elastic strain and, subsequently, the elastic moduli and Poisson’s ratio in the rolling and transverse directions. The foil was found to be elastically isotropic in the rolling plane with an effective modulus of 86 + / - 3 GPa and a Poisson’s ratio 0.39 + / - 0.04.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2013

High energy X-ray diffraction measurement of residual stresses in a monolithic aluminum clad uranium–10 wt% molybdenum fuel plate assembly

Residual stresses are expected in monolithic, aluminum clad uranium 10 wt% molybdenum (U–10Mo) nuclear fuel plates because of the large mismatch in thermal expansion between the two bonded materials. The full residual stress tensor of the U–10Mo foil in a fuel plate assembly was mapped with 0.1 mm resolution using high-energy (86 keV) X-ray diffraction. The in-plane stresses in the U–10Mo foil are strongly compressive, roughly -250 MPa in the longitudinal direction and -140 MPa in the transverse direction near the center of the fuel foil. The normal component of the stress is weakly compressive near the center of the foil and tensile near the corner. The disparity in the residual stress between the two in-plane directions far from the edges and the tensile normal stress suggest that plastic deformation in the aluminum cladding during fabrication by hot isostatic pressing also contributes to the residual stress field. A tensile in-plane residual stress is presumed to be present in the aluminum cladding to balance the large in-plane compressive stresses in the U–10Mo fuel foil, but cannot be directly measured with the current technique due to large grain size.

99 GENERAL AND MISCELLANEOUS↗