Engineering topics

Bristow, D. R.

Publications and source records attributed to Bristow, D. R..

10 records

NASA NTRS1985

Numerical approach for the aerodynamic analysis if airfoils with laminar separation

A numerical method for simultaneously and efficiently coupling an external subsonic potential flow and an interior viscous flow such that the two flows match at an interfacing boundary is discussed. Both a panel method and a simple point compressible vortex model are used for the outer potential field. The interior flow solvers which were used are the Navier-Stokes and Euler codes of T. J. Coakley and the Euler code of A. Verhoff. In order to test compatibility, the panel method is coupled to the less expensive Euler codes since the coupling procedure is identical with the Navier-Stokes code. The results show significant efficiency improvements can be obtained over the uncoupled approach. Results also indicate the outer potential flow is best represented by the simple point compressible vortex model. The panel method couples smoothly to Coakley's implicit code but is numerically incompatible as coupled with the explicit Euler code. An improved Navier-Stokes code is under initial development which extends the Euler code to include the necessary viscous terms. Results are shown for all infinite length channel with one wavy periodic wall with and without laminar separation.

Halt, D. W.↗

NASA NTRS1984

Development of MCAERO wing design panel method with interactive graphics module

A reliable and efficient iterative method has been developed for designing wing section contours corresponding to a prescribed subcritical pressure distribution. The design process is initialized by using MCAERO (MCAIR 3-D Subsonic Potential Flow Analysis Code) to analyze a baseline configuration. A second program DMCAERO is then used to calculate a matrix containing the partial derivative of potential at each control point with respect to each unknown geometry parameter by applying a first-order expansion to the baseline equations in MCAERO. This matrix is calculated only once but is used in each iteration cycle to calculate the geometry perturbation and to analyze the perturbed geometry. The potential on the new geometry is calculated by linear extrapolation from the baseline solution. This extrapolated potential is converted to velocity by numerical differentiation, and velocity is converted to pressure by using Bernoulli's equation. There is an interactive graphics option which allows the user to graphically display the results of the design process and to interactively change either the geometry or the prescribed pressure distribution.

Hawk, J. D.↗

NASA NTRS1984

Sensitivity analysis in computational aerodynamics

Information on sensitivity analysis in computational aerodynamics is given in outline, graphical, and chart form. The prediction accuracy if the MCAERO program, a perturbation analysis method, is discussed. A procedure for calculating perturbation matrix, baseline wing paneling for perturbation analysis test cases and applications of an inviscid sensitivity matrix are among the topics covered.

Bristow, D. R.↗

NASA NTRS1983

Subsonic panel method for designing wing surfaces from pressure distribution

An iterative method has been developed for designing wing section contours corresponding to a prescribed subcritical distribution of pressure. The calculations are initialized by using a surface panel method to analyze a baseline wing or wing-fuselage configuration. A first-order expansion to the baseline panel method equations is then used to calculate a matrix containing the partial derivative of potential at each control point with respect to each unknown geometry parameter. In every iteration cycle, the matrix is used both to calculate the geometry perturbation and to analyze the perturbed geometry. The distribution of potential on the perturbed geometry is established by simple linear extrapolation from the baseline solution. The extrapolated potential is converted to pressure by Bernoulli's equation. Not only is the accuracy of the approach good for very large perturbations, but the computing cost of each complete iteration cycle is substantially less than one analysis solution by a conventional panel method.

Bristow, D. R.↗

NASA NTRS1983

Aircraft aerodynamic prediction method for V/STOL transition including flow separation

A numerical procedure was developed for the aerodynamic force and moment analysis of V/STOL aircraft operating in the transition regime between hover and conventional forward flight. The trajectories, cross sectional area variations, and mass entrainment rates of the jets are calculated by the Adler-Baron Jet-in-Crossflow Program. The inviscid effects of the interaction between the jets and airframe on the aerodynamic properties are determined by use of the MCAIR 3-D Subsonic properties are determined by use of the MCAIR 3-D Subsonic Potential Flow Program, a surface panel method. In addition, the MCAIR 3-D Geometry influence Coefficient Program is used to calculate a matrix of partial derivatives that represent the rate of change of the inviscid aerodynamic properties with respect to arbitrary changes in the effective wing shape.

Gilmer, B. R.↗

NASA NTRS1982

Subsonic 3-D surface panel method for rapid analysis of multiple geometry perturbations

For any baseline aircraft configuration, a matrix of partial derivatives of surface velocity potential with respect to geometry coordinates is calculated. Linear extrapolation is then used to analyze the subcritical potential flow corresponding to a series of arbitrary small geometry perturbations. Each perturbation analysis is more than an order of magnitude more efficient than a conventional panel method solution because no influence coefficients are calculated and no large system of linear algebraic equations is solved. Wing and wing-fuselage examples are presented to demonstrate that the predicted pressure distributions are nearly exact for large changes to wing camber, thickness, and leading edge radius.

Bristow, D. R.↗

NASA NTRS1982

Subsonic panel method for the efficient analysis of multiple geometry perturbations

An accurate and efficient method was developed for the aerodynamic analysis of a series of arbitrary small geometry perturbations to a given baseline configuration. The method is appropriate for wing-fuselage configurations in incompressible potential flow. Mathematical formulations are presented for three computer programs that are employed. The first program is a conventional surface panel method for calculating the baseline singularity distribution. The second program calculates a partial derivative matrix. Each element of the matrix is the rate of change of singularity strength at one point with respect to a surface coordinate of a different point. For each baseline configuration, the calculated quantities from the first two programs establish an input file for the third. The third program calculates the surface pressure distribution and forces and moments for a series of geometry perturbations.

Bristow, D. R.↗

NASA NTRS1980

Development of panel methods for subsonic analysis and design

Two computer programs, developed for subsonic inviscid analysis and design are described. The first solves arbitrary mixed analysis design problems for multielement airfoils in two dimensional flow. The second calculates the pressure distribution for arbitrary lifting or nonlifting three dimensional configurations. In each program, inviscid flow is modelled by using distributed source doublet singularities on configuration surface panels. Numerical formulations and representative solutions are presented for the programs.

Bristow, D. R.↗

NASA NTRS1979

Improvements in surface singularity analysis and design methods

The coupling of the combined source vortex distribution of Green's potential flow function with contemporary numerical techniques is shown to provide accurate, efficient, and stable solutions to subsonic inviscid analysis and design problems for multi-element airfoils. The analysis problem is solved by direct calculation of the surface singularity distribution required to satisfy the flow tangency boundary condition. The design or inverse problem is solved by an iteration process. In this process, the geometry and the associated pressure distribution are iterated until the pressure distribution most nearly corresponding to the prescribed design distribution is obtained. Typically, five iteration cycles are required for convergence. A description of the analysis and design method is presented, along with supporting examples.

Bristow, D. R.↗

NASA NTRS1978

Modification of the Douglas Neumann program to improve the efficiency of predicting component interference and high lift characteristics

The Douglas Neumann method for low-speed potential flow on arbitrary three-dimensional lifting bodies was modified by substituting the combined source and doublet surface paneling based on Green's identity for the original source panels. Numerical studies show improved accuracy and stability for thin lifting surfaces, permitting reduced panel number for high-lift devices and supercritical airfoil sections. The accuracy of flow in concave corners is improved. A method of airfoil section design for a given pressure distribution, based on Green's identity, was demonstrated. The program uses panels on the body surface with constant source strength and parabolic distribution of doublet strength, and a doublet sheet on the wake. The program is written for the CDC CYBER 175 computer. Results of calculations are presented for isolated bodies, wings, wing-body combinations, and internal flow.

Bristow, D. R.↗