Engineering Papers⌕ Search

Engineering topics

Brian D Ramsey

Publications and source records attributed to Brian D Ramsey.

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

X-Ray Polarized View of the Accretion Geometry in the X-Ray Binary Circinus X-1

Cir X-1 is a neutron star X-ray binary characterized by strong variations influx during its eccentric∼16.6 day orbit. There are also strong variations in the spectral state, and it has historically shown both atoll and Z state properties. We observed the source with the Imaging X-ray Polarimetry Explorer during two orbital segments, 6days apart, for a total of 263 ks. We find an X-ray polarization degree in these segments of 1.6%±0.3% and1.4%±0.3% at polarization angles of 37°±5°and−12°±7°, respectively. Thus, we observed a rotation of the polarization angle by 49°±8°along the orbit. Because variations of accretion flow, and then of the hardness ratio, are expected during the orbit, we also studied the polarization binned in hardness ratio and found the polarization angle differing by 67°±11°between the lowest and highest values of the hardness ratio. We discuss possible interpretations of this result that could indicate a possible misalignment between the symmetry axes of the accretion disk and the Comptonizing region caused by the misalignment of the neutron star’s angular momentum with respect to the orbital one.

Sco-X-1↗
NASA NTRS2023

X-Ray Polarimetry of the Accreting Pulsar GX 301-2

The phase- and energy-resolved polarization measurements of accreting X-ray pulsars (XRPs) allow us to test different theoretical models of their emission, and they also provide an avenue to determine the emission region geometry. We present the results of the observations of the XRPGX 301−2 performed with the Imaging X-ray Polarimetry Explorer (IXPE). A persistent XRP, GX 301−2 has one of the longest spin periods known:∼680 s. A massive hyper-giant companion star Wray 977 supplies mass to the neutron star via powerful stellar winds. We did not detect significant polarization in the phase-averaged data when using spectropolarimetric analysis, with the upper limit on the polarization degree (PD)of 2.3% (99% confidence level). Using the phase-resolved spectropolarimetric analysis, we obtained a significant detection of polarization (above99% confidence level) in two out of nine phase bins and a marginal detection in three bins, with a PD ranging between∼3% and∼10% and a polarization angle varying in a very wide range from∼0◦to∼160◦. Using the rotating vector model, we obtained constraints on the pulsar geometry using both phase-binned and unbinned analyses, finding excellent agreement. Finally, we discuss possible reasons for a low observed polarization in GX 301−2.

GX 301-2, polarization, X-ray, X-ray binary, pulsa↗
NASA NTRS2023

Complex Variations in X-ray Polarization in the X-ray pulsar LS V +44 17 / RX J0440.9+4431

We report on Imaging X-ray polarimetry explorer (IXPE) observations of the Be-transient X-ray pulsar LS V+44 17/RX J0440.9+4431 made at two luminosity levels during the giant outburst in January–February 2023. Considering the observed spectral variability and changes in the pulse profiles, the source was likely caught in supercritical and subcritical states with significantly different emission-region geometry, associated with the presence of accretion columns and hot spots, respectively. We focus here on the pulse-phase-resolved polarimetric analysis and find that the observed dependencies of the polarization degree and polarization angle (PA) on the pulse phase are indeed drastically different for the two observations. The observed differences, if interpreted within the framework of the rotating vector model (RVM), imply dramatic variations in the spin axis inclination, the position angle, and the magnetic colatitude by tens of degrees within the space of just a few days. We suggest that the apparent changes in the observed PA phase dependence are predominantly related to the presence of an unpulsed polarized component in addition to the polarized radiation associated with the pulsar itself. We then show that the observed PA phase dependence in both observations can be explained with a single set of RVM parameters defining the pulsar’s geometry. We also suggest that the additional polarized component is likely produced by scattering of the pulsar radiation in the equatorial disk wind.

RX J0440.9+4431↗
NASA NTRS2023

X-ray Pulsar GRO J1008-57 as an Orthogonal Rotator

X-ray polarimetry is a unique way to probe the geometrical configuration of highly magnetized accreting neutron stars (X-ray pulsars).GRO J1008−57 is the first transient X-ray pulsar observed at two different flux levels by the Imaging X-ray Polarimetry Explorer (IXPE) duringits outburst in November 2022. We find the polarization properties of GRO J1008−57 to be independent of its luminosity, with the polarization degree varying between nondetection and about 15% over the pulse phase. Fitting the phase-resolved spectro-polarimetric data with the rotatingvector model allowed us to estimate the pulsar inclination (130◦, which is in good agreement with the orbital inclination), the position angle (75◦)of the pulsar spin axis, and the magnetic obliquity (∼74◦). This makes GRO J1008−57 the first confidently identified nearly orthogonal rotator among X-ray pulsars. We discuss our results in the context of the neutron star atmosphere models and theories of the axis alignment of accreting pulsars.

GRO J1008-57↗
NASA NTRS2021

The Imaging X-Ray Polarimetry Explorer (IXPE): Technical Overview IV

Scheduled to launch in late 2021,the Imaging X-ray Polarimetry Explorer (IXPE) is a Small Explorer Mission designed to open up a new window of investigation --X-ray polarimetry. The IXPE observatory features 3 identical telescopes each consisting of a mirror module assembly with a polarization-sensitive imaging x-ray detector at its focus. An extending boom, deployed on orbit, provides the necessary 4 m focal length. The payload sits atop a 3-axis stabilized spacecraft which, among other things, provides power, attitude determination and control, commanding, and telemetry to the ground. During its 2-year baseline mission, IXPE will conduct precise polarimetry for samples of multiple categories of x-ray sources, with follow-on observations of selected targets. IXPE is a partnership between NASA and the Italian Space Agency (ASI).

X-ray polarimetry↗
NASA NTRS2021

Assembly of the IXPE Mirror Modules

Expected to launch in December 2021, the Imaging X-ray Polarimetry Explorer (IXPE) is a NASA Astrophysics Small Explorer Mission with significant contributions from the Italian space agency (ASI). Three identical x-ray telescopes combine to form the IXPE Observatory. Each is comprised of a 4-m-focal length mirror module assembly (MMA, provided by Marshall Space Flight Center) that focuses x-rays onto a polarization-sensitive, imaging detector (contributed by ASI-funded institutions). This paper describes the now-completed assembly process for the 3 flight and one spare mirror modules, and compares as-tested calibrated performance with as-built metrology data. Unexpected challenges and lessons-learned are also discussed.

X-ray optics IXPE polarimetry↗
NASA NTRS2016

Toward Large-Area Sub-Arcsecond X-Ray Telescopes II

In order to advance significantly scientific objectives, future x-ray astronomy missions will likely call for x-ray telescopes with large aperture areas (approx. = 3 sq m) and fine angular resolution (approx. = 1"). Achieving such performance is programmatically and technologically challenging due to the mass and envelope constraints of space-borne telescopes and to the need for densely nested grazing-incidence optics. Such an x-ray telescope will require precision fabrication, alignment, mounting, and assembly of large areas (approx. = 600 sq m) of lightweight (approx. = 2 kg/sq m areal density) high-quality mirrors, at an acceptable cost (approx. = 1 M$/sq m of mirror surface area). This paper reviews relevant programmatic and technological issues, as well as possible approaches for addressing these issues-including direct fabrication of monocrystalline silicon mirrors, active (in-space adjustable) figure correction of replicated mirrors, static post-fabrication correction using ion implantation, differential erosion or deposition, and coating-stress manipulation of thin substrates.

Shi Ye↗