Engineering topics

Brewe, D. E.

Publications and source records attributed to Brewe, D. E..

At least 37 records · Page 2

NASA NTRS1986

Thermohydrodynamic analysis for laminar lubricating films

A Galerkin-type analysis to include thermal effects in laminar lubricating films was performed. The lubricant properties were assumed constant except for a temperature-dependent Newtonian viscosity. The cross-film temperature profile is established by collocation at the film boundaries and two interior Lobatto points. The interior temperatures are determined by requiring that the zeroth and first moment of the energy equation be satisfied across the film. The fluidity is forced to conform to a third--degree polynomial appropriate to the Lobatto-point temperatures. Preliminary indications are that the use of just two such sampling points enables satisfactory prediction of bearing performance even in the presence of substantial viscosity variation.

Elrod, H. G.↗

NASA NTRS1986

Effect of vibration amplitude on vapor cavitation in journal bearings

Computational movies were used to analyze the formation and collapse of vapor cavitation bubbles in a submerged journal bearing. The effect of vibration amplitude on vapor cavitation was studied for a journal undergoing circular whirl. The boundary conditions were implemented using Elrod's algorithm, which conserves mass flow through the cavitation bubble as well as through the oil-film region of the bearing. The vibration amplitudes for the different cases studied resulted in maximum eccentricity ratios ranging from 0.4 to 0.9. The minimum eccentricity ratio reached in each case was 0.1. For the least vibration amplitude studied in which the eccentricity ratio varied between 0.1 and 0.4, no vapor cavitation occurred. The largest vibration amplitude (i.e., eccentricity ratios of 0.1 to 0.9) resulted in vapor cavitation present 76 percent of one complete orbit.

Brewe, D. E.↗

NASA NTRS1985

Study of journal bearing dynamics using 3-dimensional motion picture graphics

Computer generated motion pictures of three dimensional graphics are being used to analyze journal bearings under dynamically loaded conditions. The motion pictures simultaneously present the motion of the journal and the pressures predicted within the fluid film of the bearing as they evolve in time. The correct prediction of these fluid film pressures can be complicated by the development of cavitation within the fluid. The numerical model that is used predicts the formation of the cavitation bubble and its growth, downstream movement, and subsequent collapse. A complete physical picture is created in the motion picture as the journal traverses through the entire dynamic cycle.

Brewe, D. E.↗

NASA NTRS1985

Theoretical modeling of the vapor cavitation in dynamically loaded journal bearings

A theoretical investigation is made of the evolution of a vapor-bubble for a submerged journal bearing under dynamically loaded conditions using the Elrod algorithm. This method conserves mass throughout the computational domain. A comparison study is performed to determine some of the consequences of applying a nonconservative theory (pseudo-Gumbel BC) to a dynamic problem. A complete dynamic cycle of a journal whirling in a circular path is chosen for the basis of comparison. Significant differences are observed in the load components near the end of the cycle. Further, good agreement with experiment is found for stationary and nonstationary cavitation.

Brewe, D. E.↗

NASA NTRS1985

Piezoviscous effects in nonconformal contacts lubricated hydrodynamically

The analysis is concerned with the piezoviscous-rigid regime of lubrication for the general case of elliptical contacts. In this regime several formulas of the lubricant film thickness have been proposed by Hamrock and Dowson, by Dowson et al., and more recently by Houpert. However, either they do not include the load parameter W, which has a strong effect on film thickness, or they overestimate the film thickness by using the Barus formula for pressure-viscosity characteristics. The Roelands formula was used for the pressure-viscosity relationship. The effects of the dimensionless load, speed, and materials parameters, the radius ratio, and the lubricant entrainment direction were investigated. The dimensionless load parameter was varied over a range of one order of magnitude. The dimensionless speed parameter was varied by 5.6 times the lowest value. Conditions corresponding to the use of solid materials of steel, bronze, and silicon nitride and lubricants of paraffinic and naphthenic mineral oil were considered in obtaining the exponent in the dimensionless materials parameter. The radius ratio was varied from 0.2 to 64 (a configuration approaching a line contact). Forty-one cases were used in obtaining a minimum film thickness formula. Contour plots indicate in detail the pressure developed between the contacting solids.

Jeng, Y. R.↗

NASA NTRS1985

Theoretical modeling of the vapor cavitation in dynamically loaded journal bearings

Brewe, D. E.↗

NASA NTRS1985

Theoretical and experimental comparison of vapor cavitation in dynamically loaded journal bearings

Vapor cavitation for a submerged journal bearing under dynamically loaded conditions was investigated. The observation of vapor cavitation in the laboratory was done by high-speed photography. It was found that vapor cavitation occurs when the tensile stress applied to the oil exceeded the tensile strength of the oil or the binding of the oil to the surface. The theoretical solution to the Reynolds equation is determined numerically using a moving boundary algorithm. This algorithm conserves mass throughout the computational domain including the region of cavitation and its boundaries. An alternating direction implicit (MDI) method is used to effect the time march. A rotor undergoing circular whirl was studied. Predicted cavitation behavior was analyzed by three-dimensional computer graphic movies. The formation, growth, and collapse of the bubble in response to the dynamic conditions is shown. For the same conditions of dynamic loading, the cavitation bubble was studied in the laboratory using high-speed photography.

Brewe, D. E.↗

NASA NTRS1984

Hydrodynamic lubrication of rigid nonconformal contacts in combined rolling and normal motion

A numerical solution to the problem of hydrodynamic lubrication of rigid point contacts with an isoviscous, incompressible lubricant was obtained. The hydrodynamic load-carrying capacity under unsteady (or dynamic) conditions arising from the combined effects of squeeze motion superposed upon the entraining motion was determined for both normal approach and separation. Superposed normal motion considerably increases net load-carrying capacity during normal approach and substantially reduces net load-carrying capacity during separation. Geometry was also found to have a significant influence on the dynamic load-carrying capacity. The ratio of dynamic to steady state load-carrying capacity increases with increasing geometry parameter for normal approach and decreases during separation. The cavitation (film rupture) boundary is also influenced significantly by the normal motion, moving downstream during approach and upstream during separation. For sufficiently high normal separation velocity the rupture boundary may even move upstream of the minimum-film-thickness position. Sixty-three cases were used to derive a functional relationship for the ratio of the dynamic to steady state load-carrying capacity in terms of the dimensionless normal velocity parameter (incorporating normal velocity, entraining velocity, and film thickness) and the geometry parameter.

Ghosh, M. K.↗

NASA NTRS1982

Geometry and starvation effects in hydrodynamic lubrication

Numerical methods were used to determine the effects of lubricant starvation on the minimum film thickness under conditions of a hydrodynamic point contact. Starvation was effected by varying the fluid inlet level. The Reynolds boundary conditions were applied at the cavitation boundary and zero pressure was stipulated at the meniscus or inlet boundary. A minimum-film-thickness equation as a function of both the ratio of dimensionless load to dimensionless speed and inlet supply level was determined. By comparing the film generated under the starved inlet condition with the film generated from the fully flooded inlet, an expression for the film reduction factor was obtained. Based on this factor a starvation threshold was defined as well as a critically starved inlet. The changes in the inlet pressure buildup due to changing the available lubricant supply are presented in the form of three dimensional isometric plots and also in the form of contour plots.

Brewe, D. E.↗

NASA NTRS1981

Analysis of starvation effects on hydrodynamic lubrication in nonconforming contacts

The effects of lubricant starvation on minimum film thickness, under conditions of a hydrodynamic point contact, are determined by numerical methods where: (1) starvation is effected by varying the fluid inlet level; (2) the Reynolds boundary conditions are applied at the cavitation boundary; and (3) zero pressure is stipulated at the meniscus or inlet boundary. Seventy-four cases were used to numerically determine a minimum-film-thickness equation, as a function of the ratio of dimensionless load to dimensionless speed for varying degrees of starvation. A film reduction factor was in turn determined as a function of the fluid inlet level, and a starved, fully-flooded boundary was defined along with an expression determining the onset of starvation. It is found that as the degree of starvation increases, the minimum film thickness decreases gradually until the fluid inlet becomes critical. The changes in the inlet pressure buildup due to changing the available lubricant supply are presented in the form of three-dimensional isometric plots.

Brewe, D. E.↗

NASA NTRS1981

Simplified solution for stresses and deformation

Conventional contact deformation analysis for ball bearings, gears, and cams involves tedious iterative procedures or the use of design charts. A simplified approach that makes the elastic deformation at the center of contact easy to calculate was previously reported. The range of validity in which these equations can be used is extended. A simplified approach to the calculation of the location and magnitude of subsurface stresses developed in machine element applications is included.

Hamrock, B. J.↗

NASA NTRS1981

Analysis of starvation effects on hydrodynamic lubrication in nonconforming contacts

Numerical methods were used to determine the effects of lubricant starvation on the minimum film thickness under conditions of a hydrodynamic point contact. Starvation was effected by varying the fluid inlet level. The Reynolds boundary conditions were applied at the cavitation boundary and zero pressure was stipulated at the meniscus or inlet boundary. A minimum-fill-thickness equation as a function of both the ratio of dimensionless load to dimensionless speed and inlet supply level was determined. By comparing the film generated under the starved inlet condition with the film generated from the fully flooded inlet, an expression for the film reduction factor was obtained. Based on this factor a starvation threshold was defined as well as a critically starved inlet. The changes in the inlet pressure buildup due to changing the available lubricant supply are presented in the form of three dimensional isometric plots and also in the form of contour plots.

Brewe, D. E.↗

NASA NTRS1979

Elastic deformation of ball bearings, gears, and cams

Simplified technique aids designers in calculation of elastic deformation at center of contact area for ball bearings, gears, cams, and similar components.

Hamrock, B. J.↗

NASA NTRS1978

Effect of geometry on hydrodynamic film thickness

The influence of geometry on the isothermal hydrodynamic film separating two rigid solids was investigated. Pressure-viscosity effects were not considered. The minimum film thickness is derived for fully flooded conjunctions by using the Reynolds boundary conditions. It was found that the minimum film thickness had the same speed, viscosity, and load dependence as Kapitza's classical solution. However, the incorporation of Reynolds boundary conditions resulted in an additional geometry effect. Solutions using the parabolic film approximation are compared with those using the exact expression for the film in the analysis. Contour plots are shown that indicate in detail the pressure developed between the solids.

Brewe, D. E.↗

NASA NTRS1978

Effect of geometry on hydrodynamic film thickness

The influence of geometry on the isothermal hydrodynamic film separating two rigid solids was investigated. Pressure-viscosity effects were not considered. The minimum film thickness is derived for fully flooded conjunctions by using the Reynolds conditions. It was found that the minimum film thickness had the same speed, viscosity, and load dependence as Kapitza's classical solution. However, the incorporation of Reynolds boundary conditions resulted in an additional geometry effect. Solutions using the parabolic film approximation are compared with those using the exact expression for the film in the analysis. Contour plots are shown that indicate in detail the pressure developed between the solids.

Brewe, D. E.↗

NASA NTRS1978

Simplified contact analysis

A simple and straightforward method for calculating the elastic deformation at the center of contact between two solids with different radii of curvature is proposed instead of the conventional contact deformation analysis for ball bearings, gears, and cams, which usually involves tedious iterative procedures or the use of design charts. Ellipticity of the contact is approximated from a least-squares power fit. Simplified expressions are derived which allow rapid calculation of deformation from the material properties and geometry of the contacting elements.

Brewe, D. E.↗

NASA NTRS1977

Simplified solution for elliptical-contact deformation between two elastic solids

A linear regression by the method of least squares is made on the geometric variables that occur in the equation for elliptical-contact deformation. The ellipticity and the complete elliptic integrals of the first and second kind are expressed as a function of the x,y-plane principal radii. The ellipticity was varied from 1 (circular contact) to 10 (a configuration approaching line contact). The procedure for solving these variables without the use of charts or a high-speed computer would be quite tedious. These simplified equations enable one to calculate easily the elliptical-contact deformation to within 3 percent accuracy without resorting to charts or numerical methods.

Brewe, D. E.↗

NASA NTRS1976

Simplified solution for point contact deformation between two elastic solids

A linear-regression by the method of least squares is made on the geometric variables that occur in the equation for point contact deformation. The ellipticity and the complete eliptic integrals of the first and second kind are expressed as a function of the x, y-plane principal radii. The ellipticity was varied from 1 (circular contact) to 10 (a configuration approaching line contact). These simplified equations enable one to calculate easily the point-contact deformation to within 3 percent without resorting to charts or numerical methods.

Brewe, D. E.↗