Engineering Papers⌕ Search

Engineering topics

Braun, M. J.

Publications and source records attributed to Braun, M. J..

61 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Plastic flow of plasma sprayed ceramics

The plastic flow of plasma-sprayed ZrO2-8Y2O3 ceramic has been measured at temperatures up to 1250 C and compared to the plastic flow of pressed and sintered ZrO2-8Y2O3. Plasma spraying of binary oxide ceramics is found to result in a metastable state which is inelastic at high temperature but can also be stabilized or devitrified through heat treating so as to decrease plastic properties. The mechanical properties of the as-plasma sprayed and devitrified ceramic sheet material was measured. An improved algorithm that incorporates the inherently nonlinear thermomechanical field equations was used to determine the influence of inelastic material behavior on the thermomechanical response of ceramic coated seal components. Significant creep was found during the thermal shock and steady heating periods with insufficient time during thermal quench to reverse the process, thereby inducing significant residual stresses into the components.

Padovan, J.↗
NASA NTRS1983

A thermomechanical model for energy propagation in a solid-fluid-solid system with one boundary in relative motion

A model is developed to predict the behavior of a thin fluid film in the wake of a tool in relative motion with respect to the table. Computational procedures are developed and limitations of the model are discussed. In general the fluid-interface temperature is controlled by conduction into the table. From the numerical results four regimes are identified: convective cooling, partial evaporation of the fluid film, extended evaporation due to a limiting evaporative heat flux, and surface dryout due to total evaporation of the fluid layer. These regimes are qualitatively illustrated in terms of the parameters film thickness, viscosity, and relative velocity.

Braun, M. J.↗
NASA NTRS1983

Thermomechanical loading of multilayered cylindrical geometries in thermal cycling from 300 to 1300 K

The principal of multiple material layering is well known as an effective method of reducing heat transfer; however, thermal gradients can impose significant loads and lead to delamination and subsequent component failure. An analysis is developed and experimental data are discussed for the thermomechanical effects of multilayered materials on a heat sink substrate of cylindrical geometry subject to thermal cycling. The geometry is heated in cross-flow by a high-velocity flame and cooled in crossflow by ambient-temperature air from a critical flow orifice. Each layer of material possesses a threshold beyond which small changes in temperature or mechanical loading greatly influence the life in thermal cycling of the layered materials. Comparisons are made between the thermomechanical loads predicted by various numerical codes for the linear case and by a simplified analytic model.

Hendricks, R. C.↗
NASA NTRS1983

Analogy between fluid cavitation and fracture mechanics

When the stresses imposed on a fluid are sufficiently large, rupture or cavitation can occur. Such conditions can exist in many two-phase flow applications, such as the choked flows, which can occur in seals and bearings. Nonspherical bubbles with large aspect ratios have been observed in fluids under rapid acceleration and high shear fields. These bubbles are geometrically similar to fracture surface patterns (Griffith crack model) existing in solids. Analogies between crack growth in solid and fluid cavitation are proposed and supported by analysis and observation (photographs). Healing phenomena (void condensation), well accepted in fluid mechanics, have been observed in some polymers and hypothesized in solid mechanics. By drawing on the strengths of the theories of solid mechanics and cavitation, a more complete unified theory can be developed.

Hendricks, R. C.↗
NASA NTRS1982

An experimental investigation of the vaporous/gaseous cavity characteristics of an eccentric journal bearing

This paper describes the experimental pressure and temperature results obtained when rotating a shaft in an eccentric lucite casing at velocities ranging from 209 to 628 rad/s (2000 to 6000 rpm). The results are presented in terms of three-dimensional plots and contour maps. Photographic evidence is presented to illustrate how the downstream and upstream regions of the cavity develop and evolve into the well-known finger patterns. A comparison between pressure and temperature profiles in air-saturated oil and carbon dioxide-saturated oil is presented; the origin and nature of the gases contained in the cavity are discussed. Three analytical models (Swift-Stieber, separation, Floberg) predicting the formation of the cavitation zone are presented and evaluated in light of the experimental results. A motion-picture supplement depicting these results is available upon request.

Braun, M. J.↗