Engineering Papers⌕ Search

Engineering topics

Bracco, F. V.

Publications and source records attributed to Bracco, F. V..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Fuel-air mixing and distribution in a direct-injection stratified-charge rotary engine

A three-dimensional model for flows and combustion in reciprocating and rotary engines is applied to a direct-injection stratified-charge rotary engine to identify the main parameters that control its burning rate. It is concluded that the orientation of the six sprays of the main injector with respect to the air stream is important to enhance vaporization and the production of flammable mixture. In particular, no spray should be in the wake of any other spray. It was predicted that if such a condition is respected, the indicated efficiency would increase by some 6 percent at higher loads and 2 percent at lower loads. The computations led to the design of a new injector tip that has since yielded slightly better efficiency gains than predicted.

Abraham, J.↗
NASA NTRS1985

Two dimensional, transient catalytic combustion of CO-air on platinum

The light off transient of catalytic combustion of lean CO-air mixtures in a platinum coated channel of a honeycomb monolith is studied with a model that resolves transient radial and axial gradients in both the gas and the solid. For the conditions studied it is concluded that: the initial heat release occurs near the entrance at the gas-solid interface and is controlled by heterogeneous reactions; large spatial and temporal temperature gradients occur in the solid near the entrance controlled mostly by the availability of fuel; the temperature of the solid near the entrance achieves almost its steady state value before significant heating of the back; heterogeneous reactions and the gas heated up front and flowing downstream heat the back of the solid; the overall transient time is controlled by the thermal inertia of the solid and by forced convection; radiation significantly influences both transient and steady state particularly near the entrance; the oxidation of CO occurs mostly on the catalyst and becomes diffusion controlled soon into the transient.

Sinha, N.↗
NASA NTRS1983

Computed and measured turbulence in axisymmetric reciprocating engines

The turbulent flowfield of a spark-ignition engine affects strongly the combustion characteristics of the engine. The flowfield depends on the design of the combustion chamber and the intake system. The present investigation is concerned with the effect of chamber design, and engine operating conditions on top dead center turbulence prior to ignition. It is shown that many of the trends which were identified in earlier studies can be obtained from a single model. The employed model takes into account a two-dimensional axisymmetric flowfield. Attention is given to governing equations, boundary and initial conditions, a comparison of the computed results with measurements, and the effect of swirl and squish.

Grasso, F.↗
NASA NTRS1983

Coupling of Transport and Chemical Processes in Catalytic Combustion

Catalytic combustors have demonstrated the ability to operate efficiently over a much wider range of fuel air ratios than are imposed by the flammability limits of conventional combustors. Extensive commercial use however needs the following: (1) the design of a catalyst with low ignition temperature and high temperature stability, (2) reducing fatigue due to thermal stresses during transient operation, and (3) the development of mathematical models that can be used as design optimization tools to isolate promising operating ranges for the numerous operating parameters. The current program of research involves the development of a two dimensional transient catalytic combustion model and the development of a new catalyst with low temperature light-off and high temperature stablity characteristics.

Bracco, F. V.↗
NASA NTRS1983

Catalytic Combustion of Propane/Air Mixtures on Platinum

A honeycomb catalyst of platinum (4.2 kg/cu m loading) over cordierite, with gamma-alumina washcoat, a cross section of 2.4 x 2.4 sq cm, a length of 7.6 cm, and a characteristic channel diameter of 1.4 mm is used as a steady flow reactor. Measurements are made with C3H8/air mixtures at 650 to 800 K inlet temperatures, 110 KPa pressure, 10 to 40 m/s inlet velocity, 0.19 to 0.32 equivalence ratios, and approximately 1.5 mole percent water content. The measured quantities are the substrate tempeature at ten axial locations, the exhaust gas temperature, the exhaust concentrations of CO, CO2, O2, and total hydrocarbons, and the pressure drop across the monolith. The measured quantities are compared with those computed with a two-dimensional steady-state model for axial and radial convection and diffusion of mass, momentum, energy and homogeneous (three overall reactions) and heterogeneous (infinitely fast) reactions. It is found that, under the tested conditions, most of the fuel is converted to CO2 and H2O at the surface. Gas-phase reactions tend rapidly to become more important as the temperature and equivalence ratio are increased and the flow velocity is decreased. Surface fuel conversion is much more rapid than fuel diffusion, resulting in diffusion-controlled oxidation.

Bruno, C.↗
NASA NTRS1973

An experimental-analytical method to study steady spray combustion.

Description of a method for determining the local parameters of the gas mixture resulting from the combustion of sprayed fuel in a gaseous oxidizer. The method is based on the measurement of local static pressures in the gas mixture and does not require the knowledge of the droplet distribution function, drag, and vaporization characteristics. A set of equations with substituted local pressure values is used for calculations. Application of the method is demonstrated on a liquid oxygen-ethanol rocket fuel.

Bracco, F. V.↗
NASA NTRS1972

A study of the steady state spray equation.

A constant cross-sectional area rocket motor was used to study the combustion of a spray of ethanol in gaseous oxygen. The variables of the combustion gas and the flux of liquid ethanol versus the distance from the injector, were determined by an experimental-analytical method which did not require any assumption about the distribution, drag, and vaporization of the fuel drops (static pressure measurements were used instead). The steady-state spray equation is solved, for various drag and vaporization models, and the local flux of liquid ethanol thus calculated is compared with the experimentally determined one for the purpose of selecting a proper spray combustion model.

Bracco, F. V.↗
NASA NTRS1967

Nonlinear acoustics

Derivation of equations describing nonlinear acoustics with emphasis on effect of first, second and bulk viscosity coefficients

Bracco, F. V.↗