Engineering Papers⌕ Search

Engineering topics

Boyle, Devin K.

Publications and source records attributed to Boyle, Devin K..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Transfer-Function Determination for Infinite-Tube-Probe Pressure Transducers with Application to Turbofan Core/Combuster Noise

Turbofan hot-section unsteady pressure measurements are complicated by environmental limitations of current-generation sensors. Accurate direct measurements are normally not possible and engine-external measurement techniques, using sufficiently long sense lines, are utilized instead. Remote measurement comes at a cost, however, as it introduces a magnitude reduction within the line as well as a phase lag relative to the desired engine-internal measurement location. Determination, or validation, of a transfer function relating the engine internal pressure to the observed remote value is necessary. Transfer functions are examined for various configurations of the so-called infinite-tube-probe arrangement in order to optimize measurement performance. The experimental setup uses a normal-incidence tube that ordinarily is utilized for impedance eduction. Here, its downstream end instead is made up of a hard-wall termination instrumented with a flush-mounted microphone and a Kulite pressure transducer as well as a sense line connection. This allows the remote and direct measurements to be related under controlled conditions. Transfer-function measurements are presented and compared to predictions for several parametric variations.

Turbomachinery Noise↗
NASA NTRS2019

Transfer-Function Determination for Infinite-Tube-Probe Pressure Transducers with Application to Turbofan Core/Combustor Noise

Turbofan hot-section unsteady pressure measurements are complicated by environmental limitations of current-generation sensors. Accurate direct measurements are normally not possible and engine-external measurement techniques, using sufficiently long sense lines, are utilized instead. Remote measurement comes at a cost, however, as it introduces a magnitude reduction within the line as well as a phase lag relative to the desired engine-internal measurement location. Determination, or validation, of a transfer function relating the engine internal pressure to the observed remote value is necessary. Transfer functions are examined for various configurations of the so-called infinite-tube-probe arrangement in order to optimize measurement performance. The experimental setup uses a normal-incidence tube that ordinarily is utilized for impedance eduction. Here, its downstream end instead is made up of a hard-wall termination instrumented with a flush-mounted microphone and a Kulite pressure transducer as well as a sense line connection. This allows the remote and direct measurements to be related under controlled conditions. Transfer-function measurements are presented and compared to predictions for several parametric variations.

Combustor Noise↗
NASA NTRS2019

1/3-Octave Analysis of Core/Combustor-Noise Measurements for the DGEN Aeropropulsion Research Turbofan with Application to Noise Prediction

This work continues the analysis of data obtained during a 2017 NASA DGEN Aeropropulsion Research Turbofan (DART) core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). The DART is a cost-efficient testbed for the study of core-noise physics and mitigation. Acoustic data were simultaneously acquired using the AAPL overhead microphone array in the engine aft-quadrant farfield, a single midfield microphone, and two infinite-tube-probe sensors for unsteady pressures at the core-nozzle exit. The data are here examined on an 1/3-octave basis as a first step in extending and improving core-noise prediction capability.

Hultgren, Lennart S.↗
NASA NTRS2019

One-Third-Octave Analysis of Core/Combustor-Noise Measurements for the DGEN Aeropropulsion Research Turbofan with Application to Noise Prediction

This work continues the analysis of data obtained during a 2017 NASA DGEN Aeropropulsion Research Turbofan (DART) core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). The DART is a cost-efficient testbed for the study of core-noise physics and mitigation. Acoustic data were simultaneously acquired using the AAPL overhead microphone array in the engine aft-quadrant farfield, a single midfield microphone, and two infinite-tube-probe sensors for unsteady pressures at the core-nozzle exit. The data are here examined on an 1/3-octave basis as a first step in extending and improving core-noise prediction capability.

Combustor Noise↗
NASA NTRS2019

Plans for Upcoming DGEN Aeropropulsion Research Turbofan (DART) Testing

This presentation serves as an overview of test plans for an upcoming DGEN Aeropropulsion Research Turbofan (DART) test entry at the NASA GRC AeroAcoustic Propulsion Laboratory (AAPL). The test entry includes: (1)a fan intra-stage velocity field survey, which will be compared to a Computational Fluid Dynamics (CFD) survey of DART, (2) an exploratory noise study of DART with several objectives focused on measurement projection to the far-field, source identification improvements and development of a barrier wall for isolation of various sources, (3) advancement of core/combustor noise research on DART using more extensive engine-mounted instrumentation, and (4) high-temperature pressure sensor technology-readiness-level (TRL) advancement.

Boyle, Devin K.↗
NASA NTRS2018

DGEN Aeropropulsion Research Turbofan (DART) Core/Combustor-Noise Infinite-Tube-Probe (ITP) Transfer Function

Direct measurements of turbofan engine core unsteady pressure is complicated by the extreme thermal environment within the engine, preventing currently available transducers from operating. It is necessary to use a remote measurement configuration such as an infinite-tube-probe (ITP) configuration in which the transducer is teed into a line pneumatically coupled with the location of interest and the other end of the ITP contains an "infinite" waveguide designed to prevent any reflections. This configuration has become a standard method for experiments concerning core noise. In order to relate the spectral pressure measurements obtained remotely with the ITP, a transfer (frequency response) function needs to be calculated based on a known pressure field. This is accomplished using a normal impedance tube at Glenn Research Center, where a flush-mounted microphone is used as a reference to the ITP signal in the calculation of the ITP's transfer function.

Boyle, Devin K.↗
NASA NTRS2018

DGEN Aeropropulsion Research Turbofan (DART) Test Plans

This presentation serves as an overview of test plans for an upcoming DGEN Aeropropulsion Research Turbofan (DART) test entry at the NASA GRC AeroAcoustic Propulsion Laboratory (AAPL). The test entry includes: (1) a fan intra-stage velocity field survey, which will be compared to a Computational Fluid Dynamics (CFD) survey of DART, (2) an exploratory noise study of DART with several objectives focused on measurement projection to the far-field, source identification improvements and development of a barrier wall for isolation of various sources, (3) advancement of core/combustor noise research on DART using more extensive engine-mounted instrumentation, and (4) high-temperature pressure sensor technology-readiness-level (TRL) advancement.

Boyle, Devin K.↗
NASA NTRS2018

Core/Combustor-Noise Baseline Measurements for the DGEN Aeropropulsion Research Turbofan

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-reduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aeropropulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This paper describes the recently completed DART core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data were simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant farfield, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. Combustor-noise components of measured total-noise signatures were educed using a two-signal source-separation method and are found to occur in the expected frequency range. The acoustic data compare well with results from a limited 2014 feasibility test and will serve as a high-quality baseline for future research using the DART. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Turbomachinery Noise↗
NASA NTRS2018

Core/Combustor-Noise Baseline Measurements for the DGEN Aeropropulsion Research Turbofan

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-eduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aeropropulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This paper describes the recently completed DART core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data was simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant far field, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. Combustor-noise components of measured total-noise signatures were educed using a two-signal source-separation method and are found to occur in the expected frequency range. The acoustic data compares well with results from a limited 2014 feasibility test and will serve as a high-quality baseline for future research using the DART. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Aeroacoustics↗
NASA NTRS2018

Core/Combuster-Noise: Preparations for Future DART Tests

The DGEN AeroPropulsion Research Turbofan (DART) is a small engine representative of commercial transport propulsors. It is used at NASA to study, among other topics, core and combustor noise production mechanisms and propagation. This includes development/validation of robust and accurate instrumentation/techniques for evaluating noise production in the extreme environment of a turbofan core. This presentation highlights upcoming core-noise research activities contributing to or directly utilizing the DART facility during the remaining CY2018 and First Quarter CY 2019 period. The near-term aim is to further investigate features seen in the baseline DART core/combustor-noise test performed in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL) during 2017 as well as to provide an improved documentation of the core noise emanating from the turbofan engine. The research is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Turbofan Combustor Noise↗
NASA NTRS2017

DART Core/Combustor-Noise Initial Test Results

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-reduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aero0propulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This presentation gives a brief description of the recently completed DART core combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data was simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant far field, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. An initial assessment shows that the data is of high quality and compares well with results from a quick 2014 feasibility test. Combustor noise components of measured total-noise signatures were educed using a two-signal source-separation method an dare found to occur in the expected frequency range. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

Aeroacoustics↗
NASA NTRS2017

Acoustic Detection of Faults and Degradation in a High-Bypass Turbofan Engine during VIPR Phase III Testing

The Vehicle Integrated Propulsion Research (VIPR) Phase III project was executed at Edwards Air Force Base, California, by the National Aeronautics and Space Administration and several industry, academic, and government partners in the summer of 2015. One of the research objectives was to use external radial acoustic microphone arrays to detect changes in the noise characteristics produced by the research engine during volcanic ash ingestion and seeded fault insertion scenarios involving bleed air valves. Preliminary results indicate the successful acoustic detection of suspected degradation as a result of cumulative exposure to volcanic ash. This detection is shown through progressive changes, particularly in the high-frequency content, as a function of exposure to greater cumulative quantities of ash. Additionally, detection of the simulated failure of the 14th stage stability bleed valve and, to a lesser extent, the station 2.5 stability bleed valve, to their fully-open fail-safe positions was achieved by means of spectral comparisons between nominal (normal valve operation) and seeded fault scenarios.

noise spectra↗
NASA NTRS2014

Preliminary Study on Acoustic Detection of Faults Experienced by a High-Bypass Turbofan Engine

The vehicle integrated propulsion research (VIPR) effort conducted by NASA and several partners provided an unparalleled opportunity to test a relatively low TRL concept regarding the use of far field acoustics to identify faults occurring in a high bypass turbofan engine. Though VIPR Phase II ground based aircraft installed engine testing wherein a multitude of research sensors and methods were evaluated, an array of acoustic microphones was used to determine the viability of such an array to detect failures occurring in a commercially representative high bypass turbofan engine. The failures introduced during VIPR testing included commanding the engine's low pressure compressor (LPC) exit and high pressure compressor (HPC) 14th stage bleed values abruptly to their failsafe positions during steady state

acoustics↗