Engineering PapersSearch

Engineering topics

Bowles, J. V.

Publications and source records attributed to Bowles, J. V..

At least 19 records

Near-Optimal Re-Entry Trajectories for Reusable Launch Vehicles

A near-optimal guidance law for the descent trajectory for earth orbit re-entry of a fully reusable single-stage-to-orbit pure rocket launch vehicle is derived. A methodology is developed to investigate using both bank angle and altitude as control variables and selecting parameters that maximize various performance functions. The method is based on the energy-state model of the aircraft equations of motion. The major task of this paper is to obtain optimal re-entry trajectories under a variety of performance goals: minimum time, minimum surface temperature, minimum heating, and maximum heading change; four classes of trajectories were investigated: no banking, optimal left turn banking, optimal right turn banking, and optimal bank chattering. The cost function is in general a weighted sum of all performance goals. In particular, the trade-off between minimizing heat load into the vehicle and maximizing cross range distance is investigated. The results show that the optimization methodology can be used to derive a wide variety of near-optimal trajectories.

Chou, H.-C.

Near-Optimal Operation of Dual-Fuel Launch Vehicles

A near-optimal guidance law for the ascent trajectory from earth surface to earth orbit of a fully reusable single-stage-to-orbit pure rocket launch vehicle is derived. Of interest are both the optimal operation of the propulsion system and the optimal flight path. A methodology is developed to investigate the optimal throttle switching of dual-fuel engines. The method is based on selecting propulsion system modes and parameters that maximize a certain performance function. This function is derived from consideration of the energy-state model of the aircraft equations of motion. Because the density of liquid hydrogen is relatively low, the sensitivity of perturbations in volume need to be taken into consideration as well as weight sensitivity. The cost functional is a weighted sum of fuel mass and volume; the weighting factor is chosen to minimize vehicle empty weight for a given payload mass and volume in orbit.

Ardema, M. D.

Propellant production from the Martian atmosphere

Results are presented from a calculation of the specific impulses that can be generated through the combustion of cryogenic CO and O2 over a range of fuel/oxidizer ratios, chamber pressures, nozzle expansion ratios, freestream pressures representative of Mars, and the limiting conditions of equilibrium and frozen nozzle flow. For an expansion ratio of 80 and 100-atm. chamber pressure, a specific impulse of 298 sec was obtained; this is comparable to the best solid rocket propellants.

Bowles, J. V.

Near-optimal energy transitions for energy-state trajectories of hypersonic aircraft

A problem of the instantaneous energy transition that occurs in energy-state approximation is considered. The transitions are modeled as a sequence of two load-factor bounded paths (either climb-dive or dive-climb). The boundary-layer equations associated with the energy-state dynamic model are analyzed to determine the precise location of the transition.

Ardema, M. D.

The use of atmospheric braking during Mars missions

The use of a high-lift, winged atmospheric entry-glide vehicle by an early Mars manned mission lasting 14-16 months allows the effective use of atmospheric braking to decelerate upon arrival at Mars. Following nearly-constant deceleration, the vehicle skips out of the atmosphere into a low planetary orbit. The maximum atmospheric heating rate thus generated is of the order of 100 W/sq cm at the stagnation point for a fully catalytic surface; the corresponding equilibrium wall temperature was 2150 K. The vehicle envisioned could be radiatively cooled to an entry speed of over 8 km/sec.

Tauber, M. E.

Helicopter rotor and engine sizing for preliminary performance estimation

Methods are presented for estimating some of the more fundamental design variables of single-rotor helicopters (tip speed, blade area, disk loading, and installed power) based on design requirements (speed, weight, fuselage drag, and design hover ceiling). The well-known constraints of advancing-blade compressibility and retreating-blade stall are incorporated into the estimation process, based on an empirical interpretation of rotor performance data from large-scale wind-tunnel tests. Engine performance data are presented and correlated with a simple model usable for preliminary design. When approximate results are required quickly, these methods may be more convenient to use and provide more insight than large digital computer programs.

Talbot, P. D.

Folding tilt rotor demonstrator feasibility study

This study considers the modification of existing aircraft to the folding tilt rotor (FTR) design configuration, and then addresses the vehicle design requirements necessary to demonstrate the FTR concept throughout the hover/transition high-speed envelope. Three potential candidates are considered: (1) the Bell/Boeing V-22 Osprey combined with either the existing TF-34 convertible engine or a conceptual convertible engine utilizing the torque-converter-coupled fan configuration; (2) a combination of the same powerplants with a modified Lockheed S-3A Viking; and (3) the NASA/Army/BELL XV-15 airframe mated with a conceptual generic turbofan engine with a fixed-pitch fan coupled to the engine by means of a torque converter. Required aircraft modifications are identified and recommended R&D efforts for engine/rotor/airframe integration are presented.

Eisenberg, J. D.

Analysis of selected VTOL concepts for a civil transportation mission

As part of defining the needs and technology requirements for VTOL aircraft research and development, the objective of this paper is to study the application of two tilt propulsion concept VTOL aircraft to the business/executive transport mission. The two concepts selected for study are the tilt jet concept utilizing rotating turbofan engines for both vertical lift and cruise thrust, and the tilt rotor concept using relatively low disc loading propellers for hover and cruise. Overall mission costs, including the time-value cost of the executives, was computed for a selected range of mission distances, up to the design mission range of 750 nm (1400 km). The total trip cost was also compared to that of a conventional helicopter/business jet combination for a typical executive transport mission.

Wilson, S. B., III

Potential benefits for propfan technology on derivatives of future short- to medium-range transport aircraft

It is noted that several NASA-sponsored studies have identified a substantial potential fuel savings for high subsonic speed aircraft utilizing the propfan concept compared to the equivalent technology turbofan aircraft. Attention is given to a feasibility study for propfan-powered short- to medium-haul commercial transport aircraft conducted to evaluate potential fuel savings and identify critical technology requirements using the latest propfan performance data. An analysis is made of the design and performance characteristics of a wing-mounted and two-aft-mounted derivative propfan aircraft configurations, based on a DC-9 Super 80 airframe, which are compared to the baseline turbofan design. Finally, recommendations for further research efforts are also made.

Goldsmith, I. M.

Requirements for regional short-haul air service and the definition of a flight program to determine neighborhood reactions to small transport aircraft

An evaluation of the current status and future requirements of an intraregional short haul air service is given. A brief definition of the different types of short haul air service is given. This is followed by a historical review of previous attempts to develop short haul air service in high density urban areas and an assessment of the current status. The requirements for intraregional air service, the need for economic and environmental viability and the need for a flight research program are defined. A detailed outline of a research program that would determine urban community reaction to frequent operations of small transport aircraft is also given. Both the operation of such an experiment in a specific region (San Francisco Bay area) and the necessary design modifications of an existing fixed wing aircraft which could be used in the experiment are established. An estimate is made of overall program costs.

Feher, K.

Application of advanced high speed turboprop technology to future civil short-haul transport aircraft design

With an overall goal of defining the needs and requirements for short-haul transport aircraft research and development, the objective of this paper is to determine the performance and noise impact of short-haul transport aircraft designed with an advanced turboprop propulsion system. This propulsion system features high-speed propellers that have more blades and reduced diameters. Aircraft are designed for short and medium field lengths; mission block fuel and direct operating costs (DOC) are used as performance measures. The propeller diameter was optimized to minimize DOC. Two methods are employed to estimate the weight of the acoustic treatment needed to reduce interior noise to an acceptable level. Results show decreasing gross weight, block fuel, DOC, engine size, and optimum propfan diameter with increasing field length. The choice of acoustic treatment method has a significant effect on the aircraft design.

Conlon, J. A.

Application of powered lift and mechanical flap concepts for civil short-haul transport aircraft design

The objective of this paper is to determine various design and performance parameters, including wing loading and thrust loading requirements, for powered-lift and mechanical flap conceptual aircraft constrained by field length and community noise impact. Mission block fuel and direct operating costs (DOC) were found for optimum designs. As a baseline, the design and performance parameters were determined for the aircraft using engines without noise suppression. The constraint of the 90 EPNL noise contour being less than 2.6 sq km (1.0 sq mi) in area was then imposed. The results indicate that for both aircraft concepts the design gross weight, DOC, and required mission block fuel decreased with field length. At field lengths less than 1100 m (3600 ft) the powered lift aircraft had lower DOC and block fuel than the mechanical flap aircraft but produced higher unsuppressed noise levels. The noise goal could easily be achieved with nacelle wall treatment only and thus resulted in little or no performance or weight penalty for all studied aircraft.

Conlon, J. A.

Study of a very low cost air combat maneuvering trainer aircraft

A very low cost aircraft for performing Air Combat Maneuvering (ACM) training was studied using the BD-5J sport plane as a point of departure. The installation of a larger engine and increased fuel capacity were required to meet the performance and mission objectives. Reduced wing area increased the simulation of the ACM engagement, and a comparison with current tactical aircraft is presented. Other factors affecting the training transfer are considered analytically, but a flight evaluation is recommended to determine the concept utility.

Hill, G. C.

Thrust and wing loading requirements for short haul aircraft constrained by engine noise and field length

Propulsion system and wing loading requirements are determined for a mechanical flap and an externally blown flap aircraft for various engine noise levels and two engine cycles. Both aircraft are sized to operate from a 914m (3000 ft) runway and perform the same mission. For each aircraft concept, propulsion system sizing is demonstrated for two different engine cycles - one having a fan pressure ratio of 1.5 and a bypass ratio of 9, and the other having a fan pressure ratio of 1.25 and a bypass ratio of 17.8. The results presented include the required thrust-to-weight ratio, wing loading, resulting gross weight, and direct operating costs, as functions of the engine noise level, for each combination of engine cycle and aircraft concept.

Bowles, J. V.

Evaluation of methods of reducing community noise impact around San Jose municipal airport

A computer simulation of the airport noise impact on the surrounding communities was used to evaluate alternate operational procedures, improved technology, and land use conversion as methods of reducing community noise impact in the airport vicinity. In addition, a constant density population distribution was analyzed for possible application to other airport communities with fairly uniform population densities and similar aircraft operational patterns. The introduction of sound absorption material (SAM) was found to reduce community noise annoyance by over 25 percent, and the introduction of refan was found to reduce community annoyance by over 60 percent. Replacing the present aircraft was found to reduce the noise problem to very small proportions, and the introduction of an advanced technology twin was found to essentially eliminate the community noise problem.

Glick, J. M.

Computer programs for estimating aircraft takeoff performance in three dimensional space

A set of computer programs has been developed to estimate the takeoff and initial climb-out maneuver of a given aircraft in three-dimensional space. The program is applicable to conventional, vectored lift and power-lift concept aircraft. The aircraft is treated as a point mass flying over a flat earth with no side slip, and the rotational dynamics have been neglected. The required input is described and a sample case presented.

Bowles, J. V.

Propulsion system sizing for powered lift and mechanical flap quiet aircraft

A method of propulsion system sizing for mechanical flap and externally blown flap aircraft is demonstrated. Included in this study is the effect of various levels of noise suppression on the aircraft final design characteristics. Both aircraft are sized to operate from a 3000-ft runway and perform the same mission. For each aircraft concept, propulsion system sizing is demonstrated for two different engine cycles - one having a fan pressure ratio of 1.5 and a bypass ratio of 9 and the other having a fan pressure ratio of 1.25 and a bypass ratio of 17.8. The results presented include the required thrust to weight ratio and wing loading and the resulting gross weight and direct operating costs as functions of the engine noise level for each of the four combinations of engine cycles and aircraft concepts.

Bowles, J. V.