Engineering topics

Bowles, D. E.

Publications and source records attributed to Bowles, D. E..

At least 19 records

NASA NTRS1992

Designing for time-dependent material response in spacecraft structures

To study the influence on overall deformations of the time-dependent constitutive properties of fiber-reinforced polymeric matrix composite materials being considered for use in orbiting precision segmented reflectors, simple sandwich beam models are developed. The beam models include layers representing the face sheets, the core, and the adhesive bonding of the face sheets to the core. A three-layer model lumps the adhesive layers with the face sheets or core, while a five-layer model considers the adhesive layers explicitly. The deformation response of the three-layer and five-layer sandwich beam models to a midspan point load is studied. This elementary loading leads to a simple analysis, and it is easy to create this loading in the laboratory. Using the correspondence principle of viscoelasticity, the models representing the elastic behavior of the two beams are transformed into time-dependent models. Representative cases of time-dependent material behavior for the facesheet material, the core material, and the adhesive are used to evaluate the influence of these constituents being time-dependent on the deformations of the beam. As an example of the results presented, if it assumed that, as a worst case, the polymer-dominated shear properties of the core behave as a Maxwell fluid such that under constant shear stress the shear strain increases by a factor of 10 in 20 years, then it is shown that the beam deflection increases by a factor of 1.4 during that time. In addition to quantitative conclusions, several assumptions are discussed which simplify the analyses for use with more complicated material models. Finally, it is shown that the simpler three-layer model suffices in many situations.

Hyer, M. W.↗

NASA NTRS1992

High performance polymers and polymer matrix composites for spacecraft structural applications

A program implemented by NASA Langley Research Center to develop and evaluate new polymers and polymer matrix composites for spacecraft structural applications is examined. Various polymeric films, moldings, and adhesives are evaluated for resistance to atomic oxygen and high energy electron and UV radiation. Thin films from the poly(arylene ether)s containing phenylphosphine oxide groups and the siloxane-epoxies exhibited minor weight loss compared to Kapton polyimide after exposure. Large doses (greater than 10 exp 9 rads) of electron radiation, simulating 30 yr of exposure in GEO, are found to alter the chemical structure of epoxies by both chain scission and cross-linking. The thermal cycling representative of both LEO and GEO environments can cause microcracking in composites which can in turn affect the dimensional stability and produce mechanical property reductions. The processing and fabrication issues associated with precision composite spacecraft components are also addressed.

Bowles, D. E.↗

NASA NTRS1992

The time-dependent response of 3- and 5-layer sandwich beams

Simple sandwich beam models have been developed to study the effect of the time-dependent constitutive properties of fiber-reinforced polymer matrix composites, considered for use in orbiting precision segmented reflectors, on the overall deformations. The 3- and 5-layer beam models include layers representing the face sheets, the core, and the adhesive. The static elastic deformation response of the sandwich beam models to a midspan point load is studied using the principle of stationary potential energy. In addition to quantitative conclusions, several assumptions are discussed which simplify the analysis for the case of more complicated material models. It is shown that the simple three-layer model is sufficient in many situations.

Hyer, M. W.↗

NASA NTRS1988

Response of composite materials to the Space Station orbit environment

The rationale for selecting composite materials with an anodized aluminum foil coating for the Space Station is presented. Data on the effects of the space service environment on these materials are given. Results are also presented on the effect of optical properties of an aluminum/aluminum oxide coating on the thermal balance of the cylindrical structural members. The resistance of this coating to solar ultraviolet degradation is discussed.

Tompkins, S. S.↗

NASA NTRS1986

Thermally induced transverse cracking in graphite-epoxy cross-ply laminates

Thermally induced transverse cracking in T300/5208 graphite-epoxy cross-ply laminates was investigated experimentally and theoretically. The six laminate configurations studied were: 0/90(3)s, 0(2)/90(2)s, 0(3)/90s, 90/0(3)s, 90(2)/0(2)s, and 90(3)/0s. The thermal load required to initiate transverse cracking was determined experimentally and compared to a theoretical prediction. Experimental results for the accumulation of transverse cracks under cyclic thermal loading between - 250 and 250 F for up to 500 thermal cycles are presented. The calculated in situ transverse-lamina strength was determined to be at least 1.9 times the unidirectional-lamina transverse tensile strength. All laminate configurations exhibited an increase in crack density with increasing thermal cycles.

Adams, D. S.↗

NASA NTRS1986

Space radiation effects on the dimensional stability of a toughened epoxy graphite composite

The effects of a simulated space radiation environment on the dimensional stability of an elastomer-toughened epoxy-graphite composite were determined. The response of the material was characterized following exposure to radiation doses equivalent to geosynchronous orbit lifetimes ranging from 6 months to 30 years. The results show that radiation interacts with the epoxy matrix to embrittle the composite, beginning at relatively low total doses (10 to the 7th power rads). The embrittlement results in thermal expansion changes and significant laminate microcracking during thermal cycling. These property changes could limit the service life of this material in some spacecraft applications.

Sykes, G. F.↗

NASA NTRS1985

The thermal and mechanical stability of composite materials for space structures

A continuing research objective of the National Aeronautical and Space Administration (NASA) is to develop advanced composite materials for space structures. The thrust of this research is to gain fundamental understanding of the performance of advanced composites in the space environment. The emphasis has been to identify and model changes in the thermal-physical properties due to induced damage and develop improved materials.

Tompkins, S. S.↗

NASA NTRS1984

Electron radiation effects on the thermal expansion of graphite/resin composites

The effects of 1 MeV electron radiation on the thermal expansion characteristics of two graphite reinforced resin matrix composite systems were studied. Specimens of both graphite/epoxy (T300/5208) and graphite/polyimide (C6000/PMR15) were irradiated to a total dose of 6 x 10 to the 9th rads at two different rates. Dynamic mechanical analyses (DMA) were performed to study changes in resin chemistry. Thermal expansion results indicate that radiation did produce permanent residual strains of up to -70 x 10 to the -6th for the graphite/epoxy when exposed to temperatures up to +280 F. However, no permaanent changes in the coefficient of thermal expansion (CTE) were observed. No permanent residual strains or changes in the CTE attributable to radiation were observed for the graphite/polyimide specimens. DMA results indicate that electron radiation caused chemical changes in the epoxy matrix. These changes resulted in a lower glass transition temperature and broader 'rubbery region' which extended into the temperature range of the thermal expansion tests.

Bowles, D. E.↗

NASA NTRS1984

Effect of microcracks on the thermal expansion of composite laminates

A finite element analysis was used to quantitatively predict the effect of matrix microcracks in the 90 deg plies of graphite/epoxy composites on the coefficient of thermal expansion in the 0 deg direction, alpha (y) (perpendicular to the cracks). Results were generated for (0m/90n)s, (0/+ or 45/90)s and (0/90/ + or - 45)s graphite/epoxy laminate configurations. Analytical predictions were compared with experimental results for the two quasi-isotropic laminate configurations. Both analytical and experimental results showed that microcracks reduced the effective stiffness of the 90 deg plies, thus causing the laminates, thermal response to be more like that of a (0) laminate. The change in alpha(y) was a function of lamina material properties, microcrack density, fiber orientation, and stacking sequence. A combination of classical lamination theory and finite element analysis was used to predict the effect of microcracks in both the 90 deg and 0 deg plies. Analytical results showed that the addition of microcracks in the 0 deg plies do affect alpha(y), but to a lesser extent than those in the 90 deg plies.

Bowles, D. E.↗

NASA NTRS1984

A laser interferometer dilatometer for thermal expansion measurements of composites

A high precision Fizeau type, laser interferometer dilatometer system has been developed for low expansion composite materials. The strain resolution is about 1 microstrain. The system is automated to operate over a large temperature range and record data during the test in real time. A technique has been developed to reduce the fringe data in real time to length changes. The dilatometer system is described and thermal expansion measurements for several fiber-reinforced and particle filled composites are presented.

Tompkins, S. S.↗

NASA NTRS1983

Characteristics of thermally-induced transverse cracks in graphite epoxy composite laminates

The characteristics of thermally induced transverse cracks in T300/5208 graphite-epoxy cross-ply and quasi-isotropic laminates were investigated both experimentally and analytically. The formation of transverse cracks and the subsequent crack spacing present during cool down to -250 F (116K) and thermal cycling between 250 and -250 F (116 and 394K) was investigated. The state of stress in the vicinity of a transverse crack and the influence of transverse cracking on the laminate coefficient of thermal expansion (CTE) was predicted using a generalized plane strain finite element analysis and a modified shear lag analysis. A majority of the cross-ply laminates experienced transverse cracking during the initial cool down to -250 F whereas the quasi-isotropic laminates remained uncracked. The in situ transverse strength of the 90 degree layers was more than 1.9 times greater than the transverse strength of the unidirectional 90 degree material for all laminates investigated.

Adams, D. S.↗

NASA NTRS1983

Space environmental effects on materials

Research efforts at NASA-Langley to characterize the durability of composite materials which are candidates or use as components on various space hardware systems are reviewed. The material applications include large space structures, antennas, cables, thermal control coatings, solar reflectors, and satellite power systems. Simulation facilities have been built to study radiation effects on polymer matrix composites, and the dimensional stability of the matrix composites and tension stabilized.

Tenny, D. R.↗

NASA NTRS1982

Development of a Priest interferometer for measurement of the thermal expansion of a graphite epoxy in the temperature range 116-366 K

The thermal expansion behavior of graphite epoxy laminates between 116 and 366 degrees Kelvin was investigated using as implementation of the Priest interferometer concept. The design, construction and use of the interferometer along with the experimental results it was used to generate are described. The experimental program consisted of 25 tests on 25.4 mm and 6.35 mm wide, 8 ply pi/4 quasi-isotropic T300-5208 graphite/epoxy specimens and 3 tests on a 25.4 mm wide unidirectional specimen. Experimental results are presented for all tests along with a discussion of the interferometer's limitations and some possible improvements in its design.

Short, J. S.↗

NASA NTRS1982

Space environmental effects on materials

Research efforts at NASA-Langley to characterize the durability of composite materials which are candidates for use as components on various space hardware systems are reviewed. The material applications include large space structures, antennas, cables, thermal control coatings, solar reflectors, and satellite power systems. Simulation facilities have been built to study radiation effects on polymer matrix composites, and the dimensional stability of the matrix composites and tension stabilized cables. Numerical models are being developed for radiation effects on the mechanical, physical, and optical properties. Additionally, chemical and microstructural analyses are performed to identify damage mechanisms and the limits of effectiveness of accelerating life tests. It is noted that no residual strength reduction has been detected in polymer films after dosages of 5 billion rads of electron radiation.

Tenney, D. R.↗

NASA NTRS1982

The effects of microcracking on the thermal expansion of graphite-epoxy composites

A study of the effects of thermal environment and microcracking in graphite epoxy composites was made. Research indicates that microcracking does affect the thermal expansion of composite laminates. The amount of reduction in thermal expansion was a function of the crack density. A maximum reduction of approximately 25% occurred in a quasi-isotropic specimen with a crack density of 2.05 mm 1 in the 90 deg plies. Laminate analysis with appropriate reductions in E sub 2 and Alpha sub 2 of the damaged plies appears to be capable of modeling the observed

Bowles, D. E.↗

NASA NTRS1982

Thermal expansion of graphite-epoxy between 116 K and 366 K

A Priest laser interferometer was developed to measure the thermal strain of composite laminates. The salient features of this interferometer are that: (1) it operates between 116 K and 366 K; (2) it is easy to operate; (3) minimum specimen preparation is required; (4) coefficients of thermal expansion in the range of 0-5 micro epsilon/K can be measured; and (5) the resolution of thermal strain is on the order of micro epsilon. The thermal response of quasi-isotropic, T300/5208, grahite-epoxy composite material was studied with this interferometer. The study showed that: (1) for the material tested, thermal cycling effects are negligible; (2) variability of thermal response from specimen to specimen may become significant at cryogenic temperatures; and (3) the thermal response of 0.6 cm and 2.5 cm wide specimens are the same above room temperature.

Short, J. S.↗

NASA NTRS1982

Moire interferometry for thermal expansion of composites

Moire interferometry by reflection is described and demonstrated for the case of a real reference grating of 1200 lines/mm. Extraneous beams can be displaced and stopped by using a wedge-shaped air gap between reference and specimen gratings. Double-order dominance, the use of diffraction sequences for reflection, the isolation of preferred sequences, and the use of two-beam interference are discussed. Experimental accuracy is enhanced significantly by using several data points to establish displacements along a line, and random errors characterized by one standard deviation can be as small as one microstrain. The method is well adapted to thermal environments, coefficients of thermal expansion of selected graphite-epoxy laminates being determined in the temperature range of 297-422 K. Very good precision was achieved for a wide range of thermal expansion coefficients, from approximately zero to 27 microstrains/K.

Bowles, D. E.↗

NASA NTRS1981

Moire interferometry for thermal expansion of composites

Moire interferometry by reflection has been demonstrated using a real reference grating of 1200 lines/mm. The method is shown to be well adapted to thermal environments. Thermal expansion coefficients of graphite-epoxy composites have been measured with high precision over a wide range from nearly zero to 3300 microstrains in the temperature range 297-422 K. Random errors characterized by one standard deviation can be as small as one microstrain.

Bowles, D. E.↗