Engineering Papers⌕ Search

Engineering topics

Bosshart, Nicholas W.

Publications and source records attributed to Bosshart, Nicholas W..

At least 19 records

Locating underground features with seismic data processing

Methods are presented for determining the location of underground features (e.g., CO 2 ). One method includes capturing, by sensors distributed throughout a region, seismic traces associated with seismic signals generated by a seismic source. For multiple sensors, active noise is identified or passive noise is measured within each seismic trace and values for attributes associated with the active or passive noise are determined. Further, an unsupervised machine-learning model, based on the values of the attributes, is utilized to determine noise characteristics for multiple sensors. The sensors are grouped in clusters based on the noise characteristics for each sensor. For multiple clusters, a noise filter is created based on the noise characteristics of the sensors in the cluster, and the noise filter of the cluster is applied, for multiple sensors, to the seismic traces of the sensor. Additionally, the filtered seismic traces are analyzed to determine a location of CO 2 underground.

47 OTHER INSTRUMENTATION↗

Optimizing conformance control for gas injection EOR in unconventional reservoirs

Field observations have shown that interference between wells caused by connected fractures commonly exists in unconventional reservoirs. The well interference effect and conformance issues could lead to minimal enhanced oil recovery response (EOR) in actual operations if they are not properly controlled. A series of data analysis, modeling, and experimental activities were performed in this study to investigate the gas EOR strategies in the Bakken Formation. Employing the embedded discrete fracture modeling technology, a multiple-well, multiple-fracture model was developed to capture the well interference and conformance issues in the Bakken. The model made it possible to investigate the complex flow behavior between wells in the EOR (huff ‘n’ puff) processes. Alternative EOR and conformance control strategies using water and surfactant injections were studied to improve oil production performance based on experimental observations. Results showed that water injection could be used for conformance control in the Bakken because of its relatively low mobility compared to gas; however, water could also block oil flow around the conformance control wells because of the high interfacial tension between oil and water. Adding surfactant to the injection water is more effective for improving gas EOR performance since surfactant reduces the oil–water interfacial tension and contact angle effectively. Up to 9.4% more oil could be produced from the huff ‘n’ puff wells in 2 years of EOR operations when rich gas was injected at only 3 MMscf/d with 6000 psi of surfactant injection in the offset wells for conformance control.

42 ENGINEERING↗

Findings on Subtask 3.1 - Bakken Rich Gas Enhanced Oil Recovery Project

Total in-place oil for the Bakken petroleum system (BPS) (which includes the Bakken and Three Forks Formations) has been estimated to be 600 billion barrels (bbl). However, BPS wells have decline rates as high as 85% over the first 3 years of their lives, and primary recovery factors typically range from 3% to 10% of original oil in place. Given the low initial recovery rates, even small incremental productivity improvements could dramatically increase technically recoverable oil in the BPS. One potential solution is enhanced oil recovery (EOR) using gas injection, such as carbon dioxide (CO2) or hydrocarbon (HC) gases. While commonly used in conventional reservoirs, CO2 EOR in unconventional tight oil reservoirs has been limited to pilot tests. EOR using rich gas (mixture of methane, ethane, and propane) has also been employed in numerous pilots in several unconventional plays and has recently been successfully applied in the Eagle Ford play. If successful, large-scale gas-based EOR in the BPS could dramatically increase oil productivity and recovery factors and extend the life of the play for decades. While CO2 may be a technically suitable working fluid for EOR in the BPS, supplies are limited and costs for using CO2 in EOR pilots are prohibitively high. Meanwhile, produced gas flaring has presented challenges for BPS operators in North Dakota. Analysis conducted by the North Dakota Pipeline Authority indicates that the current gas-gathering infrastructure in North Dakota is insufficient to accommodate all of the associated gas that is produced from the BPS. The geographically isolated location of North Dakota relative to large natural gas markets, combined with suppressed natural gas prices, has made it economically challenging for industry to invest capital in expanding gas-gathering infrastructure in the state. These circumstances led to a research program conducted by the Energy & Environmental Research Center (EERC) in partnership with Liberty Resources Management Company LLC (LR) to examine the potential to use rich gas injection for EOR and mitigate flaring. A rich gas EOR pilot test was designed and executed by LR at its Stomping Horse development area in Williams County, North Dakota. From July 2018 through May 2019, a total of 160 million standard cubic feet (MMscf) of rich produced gas was injected into the BPS using five different wells in a sequential injection strategy. LR’s Leon–Gohrick drill spacing unit (DSU) was used as the test site. Regulatory oversight was provided by the North Dakota Industrial Commission (NDIC). Technical support was provided by the EERC through a series of laboratory, modeling, and field-based activities, and additional post-pilot research activities incorporated learnings from the test, developed new laboratory data, improved fracture modeling methods, and developed machine learning and big data analytics. The results from the Stomping Horse rich gas EOR pilot activities indicate that developing an effective, economical EOR approach for the BPS will require more field tests. Another key lesson learned from the Stomping Horse tests is that detailed pre- and posttest data on reservoir conditions and fluids production are essential. Robust reservoir characterization provides information that is crucial to creating realistic geomodels and conducting valid dynamic simulations of potential EOR scenarios. A detailed understanding of the completions and production history of offset wells is also necessary for valid test result interpretations. This knowledge is essential to designing the operational parameters of injectivity tests and interpreting the results. A conformance control strategy is also essential to success. Laboratory-based examinations of rich gas interactions with reservoir fluids and rocks were conducted, with an emphasis on determining the ability to mobilize oil in the tight reservoir rocks and shales of the BPS. Injection fluid composition was shown to have a positive impact on reducing reservoir oil minimum miscibility pressure (MMP), reducing interfacial tension (IFT), and altering wettability. IFT and contact angle measurements demonstrated that wettability can be altered in the presence of rich gas, suggesting the potential to improve oil recovery. Iterative modeling of surface infrastructure and reservoir performance using data generated by the various project activities was conducted. A geologic model of the Stomping Horse area was built; history-matched oil, gas, and water production was used in simulations of various EOR scenarios. Early programmatic modeling results were used to support LR’s design and operation of the EOR pilot and to provide insight regarding optimization of future commercial-scale BPS EOR design and operations. Post-pilot modeling focused on alternative methods of understanding complex fracture networks and accelerating simulation time. These led to improved simulation run times and provide excellent history-matching results. Several of these iterative models were used as the bases for developing algorithms into machine learning and big data analytics. History matching in reservoir simulation is time-consuming and computer processing-intensive. Machine learning algorithms were created, and an automated history-matching tool was developed. A large set of synthetic reservoir simulations were created to generate well responses (oil, gas, and water production, well bottomhole pressure [BHP], and tracer or propane breakthrough) for a set of EOR operating parameters that included offset well status (open or closed), injectate (rich gas or propane), injection rate, and injection well BHP. A user interface was developed to provide real-time visualization. Machine learning-based models were developed to provide rapid forecasting of well performance given a set of user-defined EOR operating parameters. These predictive models allow the user to modify the offset well status, injection rate, and injection well BHP and rapidly forecast future production performance. The combination of real-time visualization tools with real-time forecasting tools provides a framework for real-time control—operational changes that the EOR site operator can enact (e.g., changing gas injection rates) to affect the observed performance and potentially improve the EOR outcome. There is great reason to be optimistic about the future of EOR in the Bakken. The results of the laboratory studies suggest significant potential for high rates of oil mobilization using produced field gas injection under the right conditions. The results of the lab studies, combined with rigorous statistical analysis of well production data and associated modeling efforts, confirm the notion that fluid mobility within the reservoir is controlled by fractures. As more knowledge is gained about the nature and distribution of fracture networks in the Bakken, the industry will be in a better position to predict and, ultimately, influence fluid mobility. New field tests are necessary to develop a more complete understanding of those conditions. Thoughtful and creatively engineered field tests within a well-characterized geologic setting will yield the fundamental knowledge needed to take Bakken oil production to the next level. This subtask was cofunded through the EERC–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission’s Oil and Gas Research Program and Computer Modelling Group.

04 OIL SHALES AND TAR SANDS↗

A simulation study of carbon storage with active reservoir management

As part of the Integrated Midcontinent Stacked Carbon Storage Hub (IMSCS-Hub) project led by Battelle Memorial Institute, a study was conducted to determine the feasibility of storing carbon dioxide (CO 2 ) in the stacked saline rock formations of the Sleepy Hollow Field (SHF), located in Red Willow County, southern Nebraska. A series of CO 2 injection simulation scenarios, with and without active reservoir management (ARM; brine extraction), were evaluated to investigate the feasibility of storing 50+ million tonnes (Mt) of CO 2 . The results indicated CO 2 injection combined with ARM may enable permanent storage of 50+ Mt of CO 2 . The area of review (AOR), the area in which underground sources of drinking water (USDWs) might be endangered during CO 2 injection, was assessed for the simulation scenarios. In comparison to a case without ARM, brine extraction resulted in a much smaller AOR, covering an area of 42 square miles (108.8 km 2 ), roughly one-fourth the size of an AOR resulting from CO 2 injection without ARM. Our findings, presented in this paper, indicate that CO 2 injection with ARM can improve the CO 2 storage capacity of a geologic storage complex up to 100% while also reduce the rate of pressure buildup in the subsurface, resulting in a 75% reduction in AOR. This may help in lowering carbon capture and storage project costs, risks, and effort needed to meet monitoring requirements for a storage project.

54 ENVIRONMENTAL SCIENCES↗

CO 2 Injection Monitoring with a Scalable, Automated Sparse Seismic Array

Conference presentation at American Institute of Chemical Engineers (AIChE) Annual Meeting, Virtual, November 16–20, 2020. The scalable, automated sparse seismic array (SASSA) method has been ideated as a cost-effective alternative or complementary to conventional 3D seismic methods. Based on a sparse array of receivers deployed strategically on Earth’s surface and one or more fixed seismic sources, the SASSA method can be used to study specific portions of the subsurface to detect the movement of CO 2 in a reservoir with lower environmental footprint and shorter turnaround time to deliver results than conventional 3D seismic methods. Energy & Environmental Research Center (EERC) carried out seismic monitoring of an oilfield undergoing CO 2 enhanced oil recovery in Montana, USA, using the SASSA method.

02 PETROLEUM↗

Technical Assessment of Geologic Carbon Dioxide (CO 2 ) Storage: Best Practices Derived from Phase III of the Plains CO 2 Reduction (PCOR) Partnership Program, 2007-2018

The Plains CO 2 Reduction (PCOR) Partnership, led by the Energy & Environmental Research Center (EERC), was formed as part of the U.S. Department of Energy (DOE) Regional Carbon Sequestration Partnerships (RCSP) Initiative in 2003. The RCSP Program supports deployment of carbon capture, utilization, and storage (CCUS) technologies—with primary focus on carbon utilization and geologic storage of carbon dioxide (CO 2 ) (hereafter referred to as storage)—as an essential means of reducing the carbon intensity of electricity generation and other CO 2 -emitting industrial processes. The PCOR Partnership has a growing membership, which has included over 120 industry, government, and research organizations, and over a decade of experience developing, testing, and validating methods and technologies for conducting CO 2 storage projects. Nine U.S. states and four Canadian provinces comprise the PCOR Partnership region, covering an area of 1.4 million square miles in the northern Great Plains.

02 PETROLEUM↗

Development of Intelligent Monitoring System (IMS) Modules for the Aquistore CO 2 Storage Project

The monitoring data generated at a CO 2 storage site can quickly result in large amounts of data, often requiring significant labor- and time-intensive efforts to process and analyze before being able to make operational decisions. Implementing an intelligent monitoring system (IMS) can reduce the associated data-processing and analysis costs, which can thereby improve the efficiency of the monitoring process and enable real-time operational decision-making. The Energy & Environmental Research Center (EERC) has completed a 3-year project focused on developing an IMS comprising new workflows, algorithms, and a user interface for the automation and integration of geologic carbon dioxide (CO 2 ) storage site-monitoring and simulation data. The design for the IMS was based on using injection and monitoring data acquired from Aquistore, an operating CO 2 storage project. Managed by the Petroleum Technology Research Centre, the Aquistore Project is injecting CO 2 captured from SaskPower’s coal-fired Boundary Dam Power Station into a deep saline formation for geologic storage. Using data from the Aquistore Project provided a real-world basis to develop an IMS.

47 OTHER INSTRUMENTATION↗

Statistical analysis of pulsed-neutron well logs in monitoring injected carbon dioxide

Pulsed-neutron well logs (PNLs) were acquired to monitor CO 2 storage associated with enhanced oil recovery. This work quantifies the precision of repeat PNLs using data from four wells and 15 repeat PNLs. Root-mean-square (RMS) precision for the repeat PNLs was less than 3%, indicating good agreement between the baseline and repeat PNLs. Evaluations of scaled relative difference (Scaled-D) showed variation in precision among individual wells and formations. Analysis of false-positive rates (FPRs) across the entire data set showed that a Scaled-D threshold in sandstone formations of approximately ±8% resulted in a 1% FPR. These Scaled-D precision thresholds were used to estimate the value of CO 2 saturation able to be confidently distinguished from baseline. The detection limit for CO 2 is lowest for high-porosity formations filled with saline water and is highest for low-porosity formations filled with fresh water. Thus, detection of vertical out-of-zone CO 2 migration using repeat PNLs is a function of instrument precision, petrophysical properties, and hydrology, all of which must be taken into account as part of the monitoring program. Here, the results of this work provide insight into how PNLs may be included within monitoring plans to detect vertical out-of-zone CO 2 migration along a wellbore or instances of wellbore failure and provide a quantitative basis for establishing detection limits of repeat PNLs to distinguish change from baseline conditions.

54 ENVIRONMENTAL SCIENCES↗

Best Practices for Modeling and Simulation of CO 2 Storage

The purpose of this best practices manual (BPM) is to describe lessons learned and best practices for modeling and simulation of carbon dioxide (CO 2 ) geologic storage (herein “storage”) projects. Information presented here is derived from laboratory and field storage project activities conducted by the Plains CO 2 Reduction (PCOR) Partnership. Modeling and simulation collectively comprise one of four technical elements of the adaptive management approach (AMA) formalized by the PCOR Partnership for storage project development. The other technical elements are site characterization; risk assessment; and monitoring, verification, and accounting (MVA) of injected CO 2 .

54 ENVIRONMENTAL SCIENCES↗

Quantifying CO 2 storage efficiency factors in hydrocarbon reservoirs. A detailed look at CO 2 Enhanced Oil Recovery

Carbon dioxide (CO 2 ) enhanced oil recovery (EOR) will likely be the primary means of geologic CO 2 storage during the early stages of commercial-scale carbon capture and storage (CCS) because of the inherent economic incentives as well as the abundant experience and demonstrated success in the United States, where CO 2 EOR has been employed since 1974. The work presented here estimates CO 2 storage efficiency factors in CO 2 EOR operations using a unique industry database of CO 2 EOR sites and 12 different reservoir simulation models. The simulation models encompass fluvial clastic and shallow shelf carbonate depositional environments for reservoir depths of 1219 and 2438 m (4000 and 8000 feet) and 7.6-, 20-, and 64-m (25-, 66-, and 209-foot)-thick pay zones. A novel statistical modeling technique incorporating the Michaelis–Menten function is used to generate empirical percentile estimates of CO 2 storage efficiency factors. West Texas San Andres dolomite water alternating gas (WAG) CO 2 flood performance data were used to derive P10, P50, and P90 CO 2 storage efficiency factors of 0.76, 1.28, and 1.74 Mscf/STB (stock tank barrel) of original oil in place. Median CO 2 storage efficiency factors from continuous CO 2 injection following conventional waterflood varied from 15% to 61% and 8% to 40% for fluvial clastic and shallow shelf carbonate simulation models, respectively, while those from WAG injection varied from 14% to 42% and 8% to 31%, respectively. Variation in the CO 2 storage efficiency factors was largely attributable to reservoir depth (a surrogate for reservoir pressure and temperature) and lithology (clastic versus carbonate). The results of this work provide practical information that can be used to quantify CO 2 storage resource estimates in oil reservoirs during CO 2 EOR operations (as opposed to storage following depletion) and the uncertainty associated with those estimates.

54 ENVIRONMENTAL SCIENCES↗

Aquistore CO 2 Storage Project: Numerical Modeling and Simulation Update

This updated simulation model at the EERC is now capable of reproducing (with a global history-matching error of around 7%) not only the continuous pressure response but also the well logging monitoring data such as CO 2 flow distributions at the injection well and the CO 2 breakthrough profile at the observation well. The first arrival of CO 2 at the observation well is not known. The PNL data collected in February 2016 showed clear evidence of CO 2 presence with saturation values as high as 60% at the observation well while a monitoring logging event (a pulsed-neutron decay [PND]) prior to that one, performed on December 4, 2015, showed no sign of CO 2 . The history-matching results indicate that CO 2 appears to have first arrived at the iv observation well around mid-December 2015, after approximately 8 months of injection. At the end of the history-matching process, the simulated CO 2 plume extent appears the largest in Perforation 2 with a diameter of 540 m around the injection well.

54 ENVIRONMENTAL SCIENCES↗

Subtask 1.3 – Integrated Carbon Capture and Storage for North Dakota Ethanol Production

Poster presented at Mastering the Subsurface Through Technology Innovation, Partnerships and Collaboration: Carbon Storage and Oil and Natural Gas Technologies Review Meeting, Pittsburgh, Pennsylvania, August 1–3, 2017. University of North Dakota Energy & Environmental Research Center (EERC), in partnership with the U.S. Department of Energy (DOE), North Dakota ethanol producer Red Trail Energy (RTE), and North Dakota Industrial Commission (NDIC), conducted a preliminary assessment for integrating small-scale carbon capture and storage (CCS) at an industrial ethanol production facility near Richardton, North Dakota. This preliminary assessment included a technical evaluation of CCS implementation at the RTE site, development of a provisional field implementation plan (FIP), and economic analysis. Results indicated that commercial CCS is a technically and economically viable option for the significant reduction of CO 2 emissions from ethanol generation at the RTE facility.

09 BIOMASS FUELS↗

Optimizing and Quantifying CO 2 Storage Resource in Saline Formations and Hydrocarbon Reservoirs

In an effort to reduce carbon dioxide (CO 2 ) emissions from large stationary sources, carbon capture and storage (CCS) is being investigated as one approach. This work assesses CO 2 storage resource estimation methods for deep saline formations (DSFs) and hydrocarbon reservoirs undergoing CO 2 enhanced oil recovery (EOR). Project activities were conducted using geologic modeling and simulation to investigate CO 2 storage efficiency. CO 2 storage rates and efficiencies in DSFs classified by interpreted depositional environment were evaluated at the regional scale over a 100-year time frame. A focus was placed on developing results applicable to future widespread commercial-scale CO 2 storage operations in which an array of injection wells may be used to optimize storage in saline formations. The results of this work suggest future investigations of prospective storage resource in closed or semiclosed formations need not have a detailed understanding of the depositional environment of the reservoir to generate meaningful estimates. However, the results of this work also illustrate the relative importance of depositional environment, formation depth, structural geometry, and boundary conditions on the rate of CO 2 storage in these types of systems. CO 2 EOR occupies an important place in the realm of geologic storage of CO 2 , as it is likely to be the primary means of geologic CO 2 storage during the early stages of commercial implementation, given the lack of a national policy and the viability of the current business case. This work estimates CO 2 storage efficiency factors using a unique industry database of CO 2 EOR sites and 18 different reservoir simulation models capturing fluvial clastic and shallow shelf carbonate depositional environments for reservoir depths of 1219 and 2438 meters (4000 and 8000 feet) and 7.6-, 20-, and 64-meter (25-, 66,- and 209-foot) pay zones. The results of this work provide practical information that can be used to quantify CO 2 storage resource estimates in oil reservoirs during CO 2 EOR operations (as opposed to storage following depletion) and the uncertainty associated with those estimates.

54 ENVIRONMENTAL SCIENCES↗

Plains CO 2 Reduction (PCOR) Partnership Phase III (Annual Assessment Report)

This report presents an update of Phase III PCOR Partnership activities from October 1, 2015, through September 30, 2016 (PY9) and planned activities for the following year. The Plains CO 2 Reduction (PCOR) Partnership is one of seven Regional Carbon Sequestration Partnerships (RCSPs) competitively awarded by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) in 2003 as part of a national plan to mitigate greenhouse gas emissions. The PCOR Partnership is led and managed by the Energy & Environmental Research Center (EERC) at the University of North Dakota in Grand Forks, North Dakota, and includes over 100 stakeholders from the public and private sector in Phase III. The PCOR Partnership region includes all or part of nine U.S. states and four Canadian provinces.

02 PETROLEUM↗