Engineering Papers⌕ Search

Engineering topics

Bortolon, A.

Publications and source records attributed to Bortolon, A..

At least 55 records · Page 3

Suppression of edge localized modes with real-time boron injection using the tungsten divertor in EAST

We report an observation of robust suppression of edge-localized modes (ELMs) in the Experimental Advanced Superconducting Tokamak (EAST), enabled by continuous boron (B) powder injection. Edge harmonic oscillations appear during B powder injection, providing sufficient particle transport to maintain constant density and avoid impurity accumulation in ELM-stable plasmas. Here, quasi-steady ELM suppression discharges are demonstrated with modest energy confinement improvement and over a wide range of conditions: heating power and technique variation, electron density range over a factor ~3.5, deuterium or helium ion species, and with either direction of the toroidal magnetic field. ELM suppression is observed above a threshold edge B intensity and ceases within 0.5 s of termination of the B injection. In contrast to ELM suppression accompanied by recycling reduction during Li powder injection in NSTX and EAST (Maingi et al 2018 Nucl. Fusion 58 024003), reduced recycling due to hydrogenic species retention is unnecessary for the ELM suppression with B powder injection, paving the way for its consideration as an ELM control tool for future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ELM Suppression by Boron Powder Injection and Comparison with Lithium Powder Injection on EAST

Type I edge-localized modes (ELMs) in the Experimental Advanced Superconducting Tokamak (EAST) were completely suppressed via boron powder injection into the X-point region of an upper-single null configuration over a wide range of operating conditions (2.8 < P aux < 7.5 MW, 3.8 × 10 19 < n e < 6 × 10 19 m -3 , RF-only and RF + NBI heating scenarios, both grad-B drift directions, and even He ion majority plasmas) (Sun et al. in Nucl. Fusion, 2020). A window of edge B concentration for stable long pulse operation was identified: too low and ELMs return, too high and the discharge suffers radiative collapse. The injection of boron powder above the minimum for ELM suppression coincided with the occurrence of an edge harmonic oscillation detected in magnetics (both on the high-field side and low-field side), in AXUV diodes near the upper X-point, divertor Dα emission, and in a range of other diagnostics (Diallo et al. in: Proceedings of 2020 IAEA fusion energy conference, 2021). Furthermore, no harmonic oscillation was observed when ELMs were present, and stored energy was slightly increased at constant density during ELM suppression. Core tungsten emission during ELM suppression either increased or decreased relative to ELMy H-mode, but the W emission was maintained at acceptable levels. The threshold B injection rate was measured for several conditions, and found to increase with heating power. Li powder injection into comparable discharges also resulted in a short phase of ELM suppression, but density and stored energy both decreased due to the strong pumping effect of lithium; no edge harmonic oscillation was observed with Li injection, indicating that the ELM suppression mechanisms differ. The new set of B-seeded, ELM-suppressed discharges exhibited certain characteristics of quiescent H-mode (Burrell et al. in Phys Plasmas 8:2153, 2001), but did not require high shear, counter beams, etc. The wide operating window and compatibility with RF-only discharges paves the way for future experiments targeting long pulse H-mode discharges with complete ELM suppression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observations of wall conditioning by means of boron powder injection in DIII-D H-mode plasmas

In this paper, we report observations from the DIII-D tokamak indicating that boron (B) powder injection in tokamak plasmas improves wall conditions similarly to glow discharge boronization (GDB). Isotopically enriched B powder (B 11 > 95%) was introduced gravitationally in a sequence of H-mode plasma discharges at rates up to ~160 mg s -1 for durations up to 3 s. Boron injection to cumulative amounts ≤0.1 g appeared to improve wall conditions similarly to boronization, with indications of reduced wall fueling, reduced recycling at the outer strike point and reduced impurity content at breakdown. Post-mortem analysis of graphite samples exposed to far scrape-off layer plasma fluxes during boron injection confirm the formation of a B-C layer, with average surface composition B:C ~ 1. The results suggest that injecting boron-rich powders in tokamak plasmas can effectively replenish boron films on carbon plasma facing components to improve wall conditions and extend the duration of the beneficial effects of GDB.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Divertor currents during type-I edge-localized modes on the DIII-D tokamak

Measurements of divertor currents on DIII-D lead to new insights in nonlinear edge-localized mode (ELM) dynamics and a possible mechanism to explain their explosive growth. Rapidly oscillating currents flowing into the divertor before a significant increase in divertor heat flux occurs are measured with an array of shunted tiles and characterized. Extrapolation results in total n = 0 currents of 5–10 kA flowing into a concentric circle near the strike point. The detected Fourier harmonics appear consistent with a mix of low- n modes ( n < 4) with currents up to 4 kA. A heuristic framework for ELM currents is developed based on thermoelectric origin of the tile currents with flow through regions inside of the nominal separatrix and found consistent with the current measurements. A current flow through the confined plasma leading to increased stochasticity and transport at the plasma edge could provide a mechanism for additional nonlinear growth as sought for in computational ELM simulations. Results also imply that ELM currents may open the possibility to manipulate the ELM character by perturbations through non-axisymmetric divertor bias or tile insulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview of physics studies on ASDEX Upgrade

The ASDEX Upgrade (AUG) programme, jointly run with the EUROfusion MST1 task force, continues to significantly enhance the physics base of ITER and DEMO. Here, the full tungsten wall is a key asset for extrapolating to future devices. The high overall heating power, flexible heating mix and comprehensive diagnostic set allows studies ranging from mimicking the scrape-off-layer and divertor conditions of ITER and DEMO at high density to fully non-inductive operation ( q 95 = 5.5, β N ≤ 2.8) at low density. Higher installed electron cyclotron resonance heating power ≤ 6 MW, new diagnostics and improved analysis techniques have further enhanced the capabilities of AUG.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ablation of solid pellets induced by supra-thermal ions in the far scrape-off layer of tokamak plasmas

Injection of solid pellets is a key element in several aspects of the operation of a magnetic confinement plasma reactor for fusion applications, including plasma fueling, control and diagnosis. This letter reports observations demonstrating that pellet ablation can begin outside the plasma boundary, by effect of supra-thermal ions, whose orbits, under appropriate conditions, can extend well into the vacuum region. The phenomenon was recorded during plasma discharges in the DIII-D tokamak, combining pulsed modulation of heating neutral beams, with high-frequency injection of sub-millimeter lithium pellets, and it is ascribed to the large fraction of trapped beam ions associated with counter current neutral beam injection. The effect was quantitatively evaluated by means of Monte-Carlo simulations of supra-thermal ion orbits, finding that the heat-deposition was of the order of 50-100 W/mm 2 , in the region traversed by the lithium pellets before reaching the plasma boundary, which is consistent with the severe pellet deterioration observed for low velocity pellets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Real-time wall conditioning by controlled injection of boron and boron nitride powder in full tungsten wall ASDEX Upgrade

In ASDEX Upgrade with full-tungsten wall, boronization is an important tool to control tungsten sources and allow reliable operation at low collisionality. The duration of the beneficial effects is limited by the erosion of the boron layer, in particular on the tungsten ion-cyclotron antenna limiters. We report results from experiments exploring injection boron-rich powders in tokamak plasmas as a way to replenish boron coating and extend the lifetime of boronization effects. Pure boron and boron nitride powders were introduced gravitationally in plasma discharges at rates up to 60 mg/s for durations up to 3 s. Boron injection with cumulative amounts >100 mg appeared to improve wall conditions similarly to boronization, with indications of reduced influx of oxygen and tungsten from the antenna limiter. Moreover, cumulative injection of 340 mg of B appeared sufficient to enable successful execution of low collisionality scenarios critically relying on freshly boronized walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A horizontal powder injector for W7-X

We report that injection of low-Z powders into fusion plasma has been used to improve wall conditions, similar to the standard boronization process using diborane. Powder injection has the advantage of being much simpler, non-toxic, and efficient. The W7-X stellarator is planning on utilizing powder injection in long pulse discharges; a proof-of-principle test for horizontal injection into the plasma was conceived, a Probe Mounted Particle Injector (PMPI). The PMPI concept is developed using a polyetheretherketone (PEEK) paddle wheel hub that is driven by a piezo motor, due to the high magnetic fields, that rotates at 100 deg/s. This small PMPI fits into an envelope of 120 mm diameter × 150 mm long, a standard size for Multi-Purpose Manipulator (MPM). The device is housed in a carbon cup mounted on a retractable probe that can be placed near the plasma edge, enabling powder injection ˜4–8 cm radially into the boundary plasma. The feed for the paddle is via piezo electric actuator that vibrates a funnel filled with powder into a trough for the paddle to push. The 8 paddle arms, 35 mm long and 10 mm wide, are made from 0.38 mm thick PEEK which drag slightly along the powder-filled trough bottom, becoming a spring-loaded paddle which accelerates the powder upon release. Finally, design challenges are the high ambient magnetic field, vacuum compatible materials, high temperature environment, limited rotary-drive options, and compact space. The design and testing of this new device will be presented.

36 MATERIALS SCIENCE↗

A multi-species powder dropper for magnetic fusion applications

Here, we present a device for controlled injection of a variety of materials in powder form. The system implements four independent feeder units, arranged to share a single vertical drop tube. Each unit consists of a 80 ml reservoir, coupled to a horizontal linear trough, where a layer of powder is advanced by piezo-electric agitation at a speed proportional to the applied voltage, until it falls into a drop tube. The dropper has been tested with a number of impurities of low (B, BN, C), intermediate (Si, SiC), and high Z (Sn) and a variety of microscopic structures (flakes, spheres, rocks) and sizes (5-200 μm). For low Z materials, drop rates ~2-200 mg/s have been obtained showing good repeatability and uniformity. A calibrated light-emitting diode (LED)-based flowmeter allows measuring and monitoring the drop rate during operation. The fast time-response of the four feeders allows combination of steady and pulsed injections, providing a flexible tool for controlled-dose, real-time impurity injection in fusion plasmas.

47 OTHER INSTRUMENTATION↗

Active spectroscopy measurements of the deuterium temperature, rotation, and density from the core to scrape off layer on the DIII-D tokamak (invited)

Main-ion charge exchange recombination spectroscopy (MICER) uses the neutral beam induced D α spectrum to measure the local deuterium ion ( D + ) temperature, rotation, and density, as well as parameters related to the neutral beams, fast ions, and magnetic field. An edge MICER system consisting of 16 densely packed chords was recently installed on DIII-D, extending the MICER technique from the core to the pedestal and steep gradient region of H-mode plasmas where the D + and commonly measured impurity ion properties can differ significantly. A combination of iterative collisional radiative modeling techniques and greatly accelerated spectral fitting allowed the extension of this diagnostic technique to the plasma edge where the steep gradients introduce significant diagnostic challenges. The importance of including the fast ion Dα emission in the fit to the spectrum for the edge system is investigated showing that it is typically not important except for cases which can have significant fast ion fractions near the plasma edge such as QH-mode. Example profiles from an Ohmic L-mode and a high power ITER baseline case show large differences in the toroidal rotation of the two species near the separatrix including a strong co-current D + edge rotation. As a result, the measurements and analysis demonstrate the state of the art in active spectroscopy and integrated modeling for diagnosing fusion plasmas and the importance of direct main ion measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the scattering correction of fast-ion D-alpha signals on NSTX-U

Analysis of fast-ion D-alpha (FIDA) data on National Spherical Torus Experiment-Upgrade (NSTX-U) shows that the cold Dα line contaminates the FIDA baseline. The scattered light is comparable to the FIDA emission. A scattering correction is required to extract the FIDA signal. Two methods that relate the scattered light contamination to the intensity of the cold Dα line are employed. Here, one method uses laboratory measurements with a calibration lamp; the other method uses data acquired during plasma operation and singular value decomposition analysis. Finally, after correction, both the FIDA spectra and spatial profile are in better agreement with theoretical predictions.

47 OTHER INSTRUMENTATION↗

A Quasi-Periodic Linear Feeder for the Impurity Granular Injection on DIII-D

Injection of solid nonfuel pellets has been actively used as a tool for pacing and mitigation of edge localized modes (ELMs). In DIII-D, effective ELM pacing has been demonstrated by the high-frequency injection of lithium and carbon submillimeter spheres, using the impurity granule injector (IGI). This device injects granules into the plasma at speeds up to 150 m/s, through impact with a rotating impeller. In the IGI, high-frequency granule delivery was accomplished through a vibrational granule dropper, in which high time-average rates are obtained at the cost of lack of period control. Here, we present a new in-line granule feeder, capable of delivering granules of size 0.2-2 mm with no restriction of material properties, at quasi-periodic rates of up to 150 Hz, for 0.7-mm diameter lithium granules (600 Hz using 0.3-mm granules). The new dropper mechanism combines two piezo-in-line units; one which feeds the impeller and one which circulates granules that are filtered out of the feeder path. A remotely adjustable filter eliminates granules that are stacked, oversized, or side by side allowing the formation of a single moving granule injection line. The granules fall off the in-line feeder exit one at a time, achieving a quasi-periodic delivery rate proportional to the exit speed. At higher rates, the periodicity deteriorates. This behavior was studied using high-speed cameras and electrostatic measurements, and it was found that at drop rates <60 Hz, the granule delivery period has a variation of ±25% which appears to be caused by gaps which develop in the last centimeter of the injection line, as granules exit off the moving track. The linear feeder concept is robust against bridge instabilities and clogging issues, thanks to the simple diverter filter and constant recirculation of granules. Furthermore, the open-top design of the device facilitates refilling the device from separate reservoirs and has easy access for directly monitoring operation and adjustment. This paper describes the details of the in-line feeder design, along with several design iterations. The goal is a robust in-vacuum mechanism that can deliver granule flow ranging from a single particle to a line of particles at 150 per second, using different sizes and materials from the same apparatus.

42 ENGINEERING↗

Measurement of the passive fast-ion D-alpha emission on the NSTX-U tokamak

On National Spherical Torus Experiment Upgrade, the passive fast-ion D-alpha (passive-FIDA) spectra from charge exchange (CX) between the beam ions and the background neutrals are measured and simulated. The results indicate that the passive-FIDA signal is measurable and comparable to the active-FIDA on several channels, such as at the major radius R = 117 cm. For this, active-FIDA means the active D-alpha emission from the fast ions that CX with the injected neutrals. The shapes of measured spectra are in agreement with FIDASIM simulations on many fibers. Furthermore, the passive-FIDA spatial profile agrees with the simulation. When making measurements of active-FIDA in the edge region using time-slice subtraction, variations in the passive-FIDA contribution to the signal should be considered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multi-species impurity granule injection and mass deposition projections in NSTX-U discharges

Here, by employing a neutral gas shielding (NGS) model to characterize impurity granule injection, the ablation rates for three different species of granule: lithium, boron, and carbon, are determined. Utilizing the duration of ablation events recorded on experiments performed at DIII-D to calibrate the NGS model, we quantify the ablation rate with respect to the plasma density profile. The species-specific granule shielding constant is then used to model granule ablation within NSTX-U discharges. Simulations of 300, 500 and 700 micron diameter granules injected at 50 m s –1 are presented for NSTX-U L-mode type plasmas, as well as H-mode discharges with low natural ELM frequency. Additionally, ablation calculations of 500 micron granules of each species are presented at velocities ranging from 50–150 m s –1 . In H-mode discharges these simulations show that the majority of the injected granule is ablated within or just past the edge steep gradient region. At this radial position, the perturbation to the background plasma generated by the ablating granule can lead to conditions advantageous for the rapid triggering of ELM crashes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mitigation of divertor heat flux by high-frequency ELM pacing with non-fuel pellet injection in DIII-D

Experiments have been conducted on DIII-D investigating high repetition rate injection of non-fuel pellets as a tool for pacing Edge Localized Modes (ELMs) and mitigating their transient divertor heat loads. Effective ELM pacing was obtained with injection of Li granules in different H-mode scenarios, at frequencies 3–5 times larger than the natural ELM frequency, with subsequent reduction of strike-point heat flux. However, in scenarios with high pedestal density (~6 × 10 19 m –3 ), the magnitude of granule triggered ELMs shows a broad distribution, in terms of stored energy loss and peak heat flux, challenging the effectiveness of ELM mitigation. Furthermore, transient heat-flux deposition correlated with granule injections was observed far from the strike-points. As a result, field line tracing suggest this phenomenon to be consistent with particle loss into the mid-plane far scrape-off layer, at toroidal location of the granule injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗