Engineering Papers⌕ Search

Engineering topics

Boltz, F. W.

Publications and source records attributed to Boltz, F. W..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Second-order p-iterative solution of the Lambert/Gauss problem

An algorithm is presented for efficient p-iterative solution of the Lambert/Gauss orbit-determination problem using second-order Newton iteration. The algorithm is based on a universal transformation of Kepler's time-of-flight equation and approximate inverse solutions of this equation for short-way and long-way flight paths. The approximate solutions provide both good starting values for iteration and simplified computation of the second-order term in the iteration formula. Numerical results are presented which indicate that in many cases of practical significance (except those having collinear position vectors) the algorithm produces at least eight significant digits of accuracy with just two or three steps of iteration.

Boltz, F. W.↗
NASA NTRS1977

Aerodynamic characteristics of an F-8 aircraft configuration with a variable camber wing at Mach numbers from 0.70 to 1.15

A 0.1-scale model of an F-8 aircraft was tested in the Ames 14-Foot Transonic Wind Tunnel at Mach numbers from 0.7 to 1.15. Angle of attack was varied from -2 deg. to 22 deg. at sideslip angles of 0 deg and -5 deg. Reynolds number, dictated by the atmospheric stagnation pressure, varied with Mach number from 3.4 to 4.0 million based on mean aerodynamic chord. The model was configured with a wing designed to simulate the downward deflection of the leading and trailing edges of an advanced-technology-conformal-variable camber wing. This wing was also equipped with conventional (simple hinge) flaps. In addition, the model was tested with the basic F-8 wing to provide a reference for extrapolating to flight data. In general, at all Mach numbers the use of conformal flap deflections at both the leading edge and trailing edge resulted in slightly higher maximum lift coefficients and lower drag coefficients than with the use of simple hinge flaps. There were also found to be small improvements in the pitching-moment characteristics with the use of conformal flaps.

Boltz, F. W.↗
NASA NTRS1977

Aerodynamic characteristics of an F-8 aircraft configuration with a variable camber wing at Mach numbers from 1.5 to 2.0

A 0.1-scale model of an F-8 aircraft was tested over a range of Mach numbers from 1.5 to 2.0. Reynolds number of 4.12 million was based on wing mean-aerodynamic chord for angles of attack varying from -2 deg to +12 deg. The model was equipped with an advanced-technology-conformal-variable-camber wing (ATCVCW) having simple hinge flaps. Data were also obtained for the model equipped with the basic F-8 wing and conventional flaps. Model variables included aileron and wing trailing edge deflections and horizontal tail incidence. The ATCVCW configuration produced slight improvements in lift-curve slope, drag, and static longitudinal stability over that of the basic F-8 wing configuration. Flap effectiveness was essentially the same for both wings.

Boltz, F. W.↗
NASA NTRS1974

Autonomous orbital navigation using Kepler's equation

A simple method of determining the six elements of elliptic satellite orbits has been developed for use aboard manned and unmanned spacecraft orbiting the earth, moon, or any planet. The system requires the use of a horizon sensor or other device for determining the local vertical, a precision clock or timing device, and Apollo-type navigation equipment including an inertial measurement unit (IMU), a digital computer, and a coupling data unit. The three elements defining the in-plane motion are obtained from simultaneous measurements of central angle traversed around the planet and elapsed flight time using a linearization of Kepler's equation about a reference orbit. It is shown how Kalman filter theory may also be used to determine the in-plane orbital elements. The three elements defining the orbit orientation are obtained from position angles in celestial coordinates derived from the IMU with the spacecraft vertically oriented after alignment of the IMU to a known inertial coordinate frame.

Boltz, F. W.↗
NASA NTRS1973

An experimental investigation of three oblique-wing and body combinations at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to determine the aerodynamic characteristics of three oblique high aspect ratio wings in combination with a high fineness-ratio Sears-Haack body. The three wings had the same elliptical planform and base line curvature but had different airfoil sections. One wing had an airfoil section designed to have a lift coefficient of 1.0 at a Mach number of 0.7, another to have shock-free supersonic flow over the upper surface, and the other to have a lift coefficient of 1.3 at a Mach number of 0.6. Longitudinal and lateral-directional stability data were obtained at wing yaw angles of 0 deg, 45 deg, 50 deg, and 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 7 deg and 9 deg. Reynolds numbers for the study were 4 and 6 million per foot. Flow-visualization studies were made to examine the nature of the flow on the wing surfaces. Notable differences were found in the aerodynamic characteristics of the three wing-body combinations, particularly in the lateral-directional characteristics.

Graham, L. A.↗
NASA NTRS1972

An experimental investigation of an oblique-wing and body combination at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot wind tunnel to determine the aerodynamic characteristics of an oblique high aspect ratio wing in combination with a high fineness-ratio Sears-Haack body. Longitudinal and lateral-directional stability data were obtained at wing yaw angles from 0 deg to 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 6 deg and 9 deg. The effects of changes in Reynolds number, dihedral, and trailing-edge angle were studied along with the effects of a roughness strip on the upper and lower surfaces of the wing. Flow-visualization studies were made to determine the nature of the flow on the wing surfaces.

Graham, L. A.↗